Slotted ALOHA Overlay on LoRaWAN: a Distributed Synchronization Approach

LoRaWAN is one of the most promising standards for IoT applications. Nevertheless, the high density of end-devices expected for each gateway, the absence of an effective synchronization scheme between gateway and end-devices, challenge the scalability of these networks. In this article, we propose to regulate the communication of LoRaWAN networks using a Slotted-ALOHA (S-ALOHA) instead of the classic ALOHA approach used by LoRa. The implementation is an overlay on top of the standard LoRaWAN; thus no modification in pre-existing LoRaWAN firmware and libraries is necessary. Our method is based on a novel distributed synchronization service that is suitable for low-cost IoT end-nodes. S-ALOHA supported by our synchronization service significantly improves the performance of traditional LoRaWAN networks regarding packet loss rate and network throughput.Comment: 4 pages, 8 figure

Software Defined Radio Implementation of Carrier and Timing Synchronization for Distributed Arrays

The communication range of wireless networks can be greatly improved by using distributed beamforming from a set of independent radio nodes. One of the key challenges in establishing a beamformed communication link from separate radios is achieving carrier frequency and sample timing synchronization. This paper describes an implementation that addresses both carrier frequency and sample timing synchronization simultaneously using RF signaling between designated master and slave nodes. By using a pilot signal transmitted by the master node, each slave estimates and tracks the frequency and timing offset and digitally compensates for them. A real-time implementation of the proposed system was developed in GNU Radio and tested with Ettus USRP N210 software defined radios. The measurements show that the distributed array can reach a residual frequency error of 5 Hz and a residual timing offset of 1/16 the sample duration for 70 percent of the time. This performance enables distributed beamforming for range extension applications.Comment: Submitted to 2019 IEEE Aerospace Conferenc

Software Defined Radio Localization using 802.11-style Communications

This major qualifying project implements a simple indoor localization system using software defined radio. Both time of arrival and received signal strength methods are used by an array of wireless receivers to trilaterate a cooperative transmitter. The implemented system builds upon an IEEE 802.11b-like communications platform implemented in GNU Radio. Our results indicate substantial room for improvement, particularly in the acquisition of time data. This project contributes a starting point for ongoing research in indoor localization, both through our literature review and system implementation

Location based mobile computing - a tuplespace perspective

This is the post-print version of the Article. The official published version can be accessed from the link below - Copyright @ 2006 IOS PressLocation based or "context aware" computing is becoming increasingly recognized as a vital part of a mobile computing environment. As a consequence, the need for location-management middleware is widely recognized and actively researched. Location-management is frequently offered to the application through a "location API" (e.g. JSR 179) where the mobile unit can find out its own location as coordinates or as "building, floor, room" values. It is then up to the application to map the coordinates into a set of localized variables, e.g. direction to the nearest bookshop or the local timezone. It is the opinion of the authors that a localization API should be more transparent and more integrated: The localized values should be handed to the application directly, and the API for doing so should be the same as the general storage mechanisms. Our proposed middleware for location and context management is built on top of Mobispace. Mobispace is a distributed tuplespace made for mobile units (J2me) where replication between local replicas takes place with a central server (over GPRS) or with other mobile units (using Bluetooth). Since a Bluetooth connection indicates physical proximity to another node, a set of stationary nodes may distribute locality information over Bluetooth connections, and this information may be retrieved through the ordinary tuplespace API. Besides the integration with the general framework for communication and coordination the middleware offers straightforward answers to questions like: Where is node X located? Which nodes are near me? What is the trace of node Y

Synchronization of multihop wireless sensor networks at the application layer

Time synchronization is a key issue in wireless sensor networks; timestamping collected data, tasks scheduling, and efficient communications are just some applications. From all the existing techniques to achieve synchronization, those based on precisely time-stamping sync messages are the most accurate. However, working with standard protocols such as Bluetooth or ZigBee usually prevents the user from accessing lower layers and consequently reduces accuracy. A receiver-to-receiver schema improves timestamping performance because it eliminates the largest non-deterministic error at the sender’s side: the medium access time. Nevertheless, utilization of existing methods in multihop networks is not feasible since the amount of extra traffic required is excessive. In this article, we present a method that allows accurate synchronization of large multihop networks, working at the application layer while keeping the message exchange to a minimum. Through an extensive experimental study, we evaluate the protocol’s performance and discuss the factors that influence synchronization accuracy the most.Ministerio de Ciencia y Tecnología TIN2006-15617-C0