A Bang-Bang All-Digital PLL for Frequency Synthesis

abstract: Phase locked loops are an integral part of any electronic system that requires a clock signal and find use in a broad range of applications such as clock and data recovery circuits for high speed serial I/O and frequency synthesizers for RF transceivers and ADCs. Traditionally, PLLs have been primarily analog in nature and since the development of the charge pump PLL, they have almost exclusively been analog. Recently, however, much research has been focused on ADPLLs because of their scalability, flexibility and higher noise immunity. This research investigates some of the latest all-digital PLL architectures and discusses the qualities and tradeoffs of each. A highly flexible and scalable all-digital PLL based frequency synthesizer is implemented in 180 nm CMOS process. This implementation makes use of a binary phase detector, also commonly called a bang-bang phase detector, which has potential of use in high-speed, sub-micron processes due to the simplicity of the phase detector which can be implemented with a simple D flip flop. Due to the nonlinearity introduced by the phase detector, there are certain performance limitations. This architecture incorporates a separate frequency control loop which can alleviate some of these limitations, such as lock range and acquisition time.Dissertation/ThesisM.S. Electrical Engineering 201

Novel structures for high-speed delta-sigma data converters

As CMOS processes keep scaling down devices, the maximum operating frequencies of CMOS devices increase, and hence circuits can process very wide band signals. Moreover, the small physical dimensions of transistors allow the placing of many more blocks into a single chip, including highly accurate analog blocks and complicated digital blocks, which can process audio to communication data. Nowadays, wideband and low-power data converter is mandatory for mobile applications which need a bridge between analog and digital blocks. In this dissertation, low-power and wideband techniques are proposed. An embedded-adder quantizer with dynamic preamplifier is proposed to achieve power-efficient operation. Various double-sampling schemes are studied, and novel schemes are presented to achieve wideband operation without noise folding effect. To reduce timing delay and idle tones, a high speed DEM which alternates two sets of comparator references is proposed. Multi-cell architecture is studied to insure higher performance when the number of modulators increases. 0.18 um double-poly/4-metal CMOS process was used to implement a prototype IC. 20 MHz signal bandwidth was achieved with a 320 MHz sampling clock. The peak SNDR was 63 dB. The figure-of-merit FoM = P/(2*BW*2[superscript ENOB]) was 0.35 pJ/conversion, with a 16 mW power consumption. Measurement results show that the proposed design ideas are useful for low-power and wideband delta-sigma modulators which have low OSR. A second-order noise-coupled modulator with an embedded-zero optimization was proposed to reduce power consumption by eliminating some of the integrators. This architecture makes easier the implementation of the small feedback capacitors for high OSR modulators

High-Speed Delta-Sigma Data Converters for Next-Generation Wireless Communication

In recent years, Continuous-time Delta-Sigma(CT-ΔΣ) analog-to-digital converters (ADCs) have been extensively investigated for their use in wireless receivers to achieve conversion bandwidths greater than 15 MHz and higher resolution of 10 to 14 bits. This dissertation investigates the current state-of-the-art high-speed single-bit and multi-bit Continuous-time Delta-Sigma modulator (CT-ΔΣM) designs and their limitations due to circuit non-idealities in achieving the performance required for next-generation wireless standards. Also, we presented complete architectural and circuit details of a high-speed single-bit and multi-bit CT-ΔΣM operating at a sampling rate of 1.25 GSps and 640 MSps respectively (the highest reported sampling rate in a 0.13 μm CMOS technology node) with measurement results. Further, we propose novel hybrid ΔΣ architecture with two-step quantizer to alleviate the bandwidth and resolution bottlenecks associated with the contemporary CT-ΔΣM topologies. To facilitate the design with the proposed architecture, a robust systematic design method is introduced to determine the loop-filter coefficients by taking into account the non-ideal integrator response, such as the finite opamp gain and the presence of multiple parasitic poles and zeros. Further, comprehensive system-level simulation is presented to analyze the effect of two-step quantizer non-idealities such as the offset and gain error in the sub-ADCs, and the current mismatch between the MSB and LSB elements in the feedback DAC. The proposed novel architecture is demonstrated by designing a high-speed wideband 4th order CT-ΔΣ modulator prototype, employing a two-step quantizer with 5-bits resolution. The proposed modulator takes advantage of the combination of a high-resolution two-step quantization technique and an excess-loop delay (ELD) compensation of more than one clock cycle to achieve lower-power consumption (28 mW), higher dynamic range (\u3e69 dB) with a wide conversion bandwidth (20 MHz), even at a lower sampling rate of 400 MHz. The proposed modulator achieves a Figure of Merit (FoM) of 340 fJ/level

A digital polar transmitter for multi-band OFDM Ultra-WideBand

Linear power amplifiers used to implement the Ultra-Wideband standard must be backed off from optimum power efficiency to meet the standard specifications and the power efficiency suffers. The problem of low efficiency can be mitigated by polar modulation. Digital polar architectures have been employed on numerous wireless standards like GSM, EDGE, and WLAN, where the fractional bandwidths achieved are only about 1%, and the power levels achieved are often in the vicinity of 20 dBm. Can the architecture be employed on wireless standards with low-power and high fractional bandwidth requirements and yet achieve good power efficiency? To answer these question, this thesis studies the application of a digital polar transmitter architecture with parallel amplifier stages for UWB. The concept of the digital transmitter is motivated and inspired by three factors. First, unrelenting advances in the CMOS technology in deep-submicron process and the prevalence of low-cost Digital Signal processing have resulted in the realization of higher level of integration using digitally intensive approaches. Furthermore, the architecture is an evolution of polar modulation, which is known for high power efficiency in other wireless applications. Finally, the architecture is operated as a digital-to-analog converter which circumvents the use of converters in conventional transmitters. Modeling and simulation of the system architecture is performed on the Agilent Advanced Design System Ptolemy simulation platform. First, by studying the envelope signal, we found that envelope clipping results in a reduction in the peak-to-average power ratio which in turn improves the error vector magnitude performance (figure of merit for the study). In addition, we have demonstrated that a resolution of three bits suffices for the digital polar transmitter when envelope clipping is performed. Next, this thesis covers a theoretical derivation for the estimate of the error vector magnitude based on the resolution, quantization and phase noise errors. An analysis on the process variations - which result in gain and delay mismatches - for a digital transmitter architecture with four bits ensues. The above studies allow RF designers to estimate the number of bits required and the amount of distortion that can be tolerated in the system. Next, a study on the circuit implementation was conducted. A DPA that comprises 7 parallel RF amplifiers driven by a constant RF phase-modulated signal and 7 cascode transistors (individually connected in series with the bottom amplifiers) digitally controlled by a 3-bit digitized envelope signal to reconstruct the UWB signal at the output. Through the use of NFET models from the IBM 130-nm technology, our simulation reveals that our DPA is able to achieve an EVM of - 22 dB. The DPA simulations have been performed at 3.432 GHz centre frequency with a channel bandwidth of 528 MHz, which translates to a fractional bandwidth of 15.4%. Drain efficiencies of 13.2/19.5/21.0% have been obtained while delivering -1.9/2.5/5.5 dBm of output power and consuming 5/9/17 mW of power. In addition, we performed a yield analysis on the digital polar amplifier, based on unit-weighted and binary-weighted architecture, when gain variations are introduced in all the individual stages. The dynamic element matching method is also introduced for the unit-weighted digital polar transmitter. Monte Carlo simulations reveal that when the gain of the amplifiers are allowed to vary at a mean of 1 with a standard deviation of 0.2, the binary-weighted architecture obtained a yield of 79%, while the yields of the unit-weighted architectures are in the neighbourhood of 95%. Moreover, the dynamic element matching technique demonstrates an improvement in the yield by approximately 3%. Finally, a hardware implementation for this architecture based on software-defined arbitrary waveform generators is studied. In this section, we demonstrate that the error vector magnitude results obtained with a four-stage binary-weighted digital polar transmitter under ideal combining conditions fulfill the European Computer Manufacturers Association requirements. The proposed experimental setup, believed to be the first ever attempted, confirm the feasibility of a digital polar transmitter architecture for Ultra-Wideband. In addition, we propose a number of power combining techniques suitable for the hardware implementation. Spatial power combining, in particular, shows a high potential for the digital polar transmitter architecture. The above studies demonstrate the feasibility of the digital polar architecture with good power efficiency for a wideband wireless standard with low-power and high fractional bandwidth requirements

High Speed Reconfigurable NRZ/PAM4 Transceiver Design Techniques

While the majority of wireline standards use simple binary non-return-to-zero (NRZ) signaling, four-level pulse-amplitude modulation (PAM4) standards are emerging to increase bandwidth density. This dissertation proposes efficient implementations for high speed NRZ/PAM4 transceivers. The first prototype includes a dual-mode NRZ/PAM4 serial I/O transmitter which can support both modulations with minimum power and hardware overhead. A source-series-terminated (SST) transmitter achieves 1.2Vpp output swing and employs lookup table (LUT) control of a 31-segment output digital-to-analog converter (DAC) to implement 4/2-tap feed-forward equalization (FFE) in NRZ/PAM4 modes, respectively. Transmitter power is improved with low-overhead analog impedance control in the DAC cells and a quarter-rate serializer based on a tri-state inverter-based mux with dynamic pre-driver gates. The transmitter is designed to work with a receiver that implements an NRZ/PAM4 decision feedback equalizer (DFE) that employs 1 finite impulse response (FIR) and 2 infinite impulse response (IIR) taps for first post-cursor and long-tail ISI cancellation, respectively. Fabricated in GP 65-nm CMOS, the transmitter occupies 0.060mm² area and achieves 16Gb/s NRZ and 32Gb/s PAM4 operation at 10.4 and 4.9 mW/Gb/s while operating over channels with 27.6 and 13.5dB loss at Nyquist, respectively. The second prototype presents a 56Gb/s four-level pulse amplitude modulation (PAM4) quarter-rate wireline receiver which is implemented in a 65nm CMOS process. The frontend utilize a single stage continuous time linear equalizer (CTLE) to boost the main cursor and relax the pre-cursor cancelation requirement, requiring only a 2-tap pre-cursor feed-forward equalization (FFE) on the transmitter side. A 2-tap decision feedback equalizer (DFE) with one finite impulse response (FIR) tap and one infinite impulse response (IIR) tap is employed to cancel first post-cursor and longtail inter-symbol interference (ISI). The FIR tap direct feedback is implemented inside the CML slicers to relax the critical timing of DFE and maximize the achievable data-rate. In addition to the per-slice main 3 data samplers, an error sampler is utilized for background threshold control and an edge-based sampler performs both PLL-based CDR phase detection and generates information for background DFE tap adaptation. The receiver consumes 4.63mW/Gb/s and compensates for up to 20.8dB loss when operated with a 2- tap FFE transmitter. The experimental results and comparison with state-of-the-art shows superior power efficiency of the presented prototypes for similar data-rate and channel loss. The usage of proposed design techniques are not limited to these specific prototypes and can be applied for any wireline transceiver with different modulation, data-rate and CMOS technology

Concepts for smart AD and DA converters

This thesis studies the `smart' concept for application to analog-to-digital and digital-to-analog converters. The smart concept aims at improving performance - in a wide sense - of AD/DA converters by adding on-chip intelligence to extract imperfections and to correct for them. As the smart concept can correct for certain imperfections, it can also enable the use of more efficient architectures, thus yielding an additional performance boost. Chapter 2 studies trends and expectations in converter design with respect to applications, circuit design and technology evolution. Problems and opportunities are identfied, and an overview of performance criteria is given. Chapter 3 introduces the smart concept that takes advantage of the expected opportunities (described in chapter 2) in order to solve the anticipated problems. Chapter 4 applies the smart concept to digital-to-analog converters. In the discussed example, the concept is applied to reduce the area of the analog core of a current-steering DAC. It is shown that a sub-binary variable-radix approach reduces the area of the current-source elements substantially (10x compared to state-of-the-art), while maintaining accuracy by a self-measurement and digital pre-correction scheme. Chapter 5 describes the chip implementation of the sub-binary variable-radix DAC and discusses the experimental results. The results confirm that the sub-binary variable-radix design can achieve the smallest published current-source-array area for the given accuracy (12bit). Chapter 6 applies the smart concept to analog-to-digital converters, with as main goal the improvement of the overall performance in terms of a widely used figure-of-merit. Open-loop circuitry and time interleaving are shown to be key to achieve high-speed low-power solutions. It is suggested to apply a smart approach to reduce the effect of the imperfections, unintentionally caused by these key factors. On high-level, a global picture of the smart solution is proposed that can solve the problems while still maintaining power-efficiency. Chapter 7 deals with the design of a 500MSps open-loop track-and-hold circuit. This circuit is used as a test case to demonstrate the proposed smart approaches. Experimental results are presented and compared against prior art. Though there are several limitations in the design and the measurement setup, the measured performance is comparable to existing state-of-the-art. Chapter 8 introduces the first calibration method that counteracts the accuracy issues of the open-loop track-and-hold. A description of the method is given, and the implementation of the detection algorithm and correction circuitry is discussed. The chapter concludes with experimental measurement results. Chapter 9 introduces the second calibration method that targets the accuracy issues of time-interleaved circuits, in this case a 2-channel version of the implemented track-and-hold. The detection method, processing algorithm and correction circuitry are analyzed and their implementation is explained. Experimental results verify the usefulness of the method