Boost Matrix Converters in Clean Energy Systems

This dissertation describes an investigation of novel power electronic converters, based on the ultra-sparse matrix topology and characterized by the minimum number of semiconductor switches. The Z-source, Quasi Z-source, Series Z-source and Switched-inductor Z-source networks were originally proposed for boosting the output voltage of power electronic inverters. These ideas were extended here on three-phase to three-phase and three-phase to single-phase indirect matrix converters. For the three-phase to three-phase matrix converters, the Z-source networks are placed between the three-switch input rectifier stage and the output six-switch inverter stage. A brief shoot-through state produces the voltage boost. An optimal pulse width modulation technique was developed to achieve high boosting capability and minimum switching losses in the converter. For the three-phase to single-phase matrix converters, those networks are placed similarly. For control purposes, a new modulation technique has been developed. As an example application, the proposed converters constitute a viable alternative to the existing solutions in residential wind-energy systems, where a low-voltage variable-speed generator feeds power to the higher-voltage fixed-frequency grid.Comprehensive analytical derivations and simulation results were carried out to investigate the operation of the proposed converters. Performance of the proposed converters was then compared between each other as well as with conventional converters. The operation of the converters was experimentally validated using a laboratory prototype

Z Source Inverter Topologies-A Survey

Need for alternative energy sources to satisfy the rising demand in energy consumption elicited the research in the area of power converters/inverters. An increasing interest of using Z source inverter/converter in power generation involving renewable energy sources like wind and solar energy for both off grid and grid tied schemes were originated from 2003. This paper surveys the literature of Z source inverters/converter topologies that were developed over the years

Model and Design of a Power Driver for Piezoelectric Stack Actuators

A power driver has been developed to control piezoelectric stack actuators used in automotive application. A FEM model of the actuator has been implemented starting from experimental characterization of the stack and mechanical and piezoelectric parameters. Experimental results are reported to show a correct piezoelectric actuator driving method and the possibility to obtain a sensor-less positioning contro

Z-source matrix rectifier

This paper presents a novel Z-source matrix rectifier(ZSMR). To overcome the inherent disadvantage that the voltage transfer ratio for traditional matrix rectifier cannot be more than 0.866, a Z-source network has been combined with the matrix rectifier. The proposed rectifier realizes a voltage-boost function and the Z-source network also serves as power storage and guarantees double filtration grade at the output of the rectifier. The open-circuit zero state is required to obtain the voltage-boost function and ensure the output angle of the current vector to be invariant to obtain the expected power factor. In addition, to widely extend the voltage transfer ratio of the proposed rectifier, this paper presents the switched-inductor matrix rectifier(SL-ZSMR) and tapped-inductor matrix rectifier(TL-ZSMR). The corresponding circuit topologies, control strategies and operating principles are introduced. Both simulation and experiment results are shown to verify the theoretical analysis

Predictive current control with instantaneous reactive power minimization for a four-leg indirect matrix converter

This paper presents the experimental valida¬tion of a predictive current control strategy with minimiza¬tion of the instantaneous reactive input power for a Four-Leg Indirect Matrix Converter (4Leg-IMC). The topology includes an input matrix converter stage, which provides the dc voltage for a four-leg voltage source converter (VSC) output stage. The VSC’s fourth leg provides a path for the zero sequence load current. The control technique is based on a finite control set model predictive control (FCS-MPC) strategy, whereby the switching states for the input and out¬put converters are selected by evaluating a predictive cost function. This results in a simpler approach than that seen in other well-known modulation methods, such as three-dimensional space vector modulation (3D-SVM). Positive dc voltage, (a requirement for the safe operation of the IMC) and minimization of the instantaneous input reactive power are obtained, while maintaining good tracking of the load reference currents. Furthermore, soft switching is achieved by synchronizing the state changes in the input stage with the application of zero voltage space vectors in the inverter stage. The control strategy is experimentally verified using a laboratory prototype

A new class of hybrid AC/AC direct power converters

Variable voltage and variable frequency conversion of electrical energy from an AC source to an AC load is done in traditional power converters via a DC-link where an energy storage element (electrolytic capacitors) is situated. Despite its well-known benefits, it has the disadvantage of being bulky and to limit the converter lifetime. On the other hand, Direct Power Conversion (DPC) is an attractive concept, which doesn’t need an energy storage buffer, but has two main disadvantages: reduced voltage transfer ratio (<0.86) and low immunity to voltage supply disturbances. This paper proposes a new approach to perform the power conversion by mixing various standard topologies of well-known power converters in order to improve their performance/behavior. Simulation and experimental results prove that the hybrid structures are able to boost the output voltage capability (some above unity) and/or to fully compensate unbalanced voltage supply

A new class of hybrid AC/AC direct power converters

Variable voltage and variable frequency conversion of electrical energy from an AC source to an AC load is done in traditional power converters via a DC-link where an energy storage element (electrolytic capacitors) is situated. Despite its well-known benefits, it has the disadvantage of being bulky and to limit the converter lifetime. On the other hand, Direct Power Conversion (DPC) is an attractive concept, which doesn’t need an energy storage buffer, but has two main disadvantages: reduced voltage transfer ratio (<0.86) and low immunity to voltage supply disturbances. This paper proposes a new approach to perform the power conversion by mixing various standard topologies of well-known power converters in order to improve their performance/behavior. Simulation and experimental results prove that the hybrid structures are able to boost the output voltage capability (some above unity) and/or to fully compensate unbalanced voltage supply