1,898 research outputs found
Recommended from our members
Laboratory and field trials evaluation of transmit delay Diversity applied to DVB-T/H networks
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The requirements for future DVB-T/H networks demand that broadcasters design and
deploy networks that provide ubiquitous reception in challenging indoors and other
obstructed situations. It is essential that such networks are designed cost-effectively and with minimized environmental impact. The use of transmit diversity techniques with
multiple antennas have long been proposed to improve the performance and capacity of
wireless systems. Transmit diversity exploits the scattering effect inherent in the channel by means of transmitting multiple signals in a controlled manner from spatially separated antennas, allowing independently faded signals to arrive at the receiver and improves the chances of decoding a signal of acceptable quality. Transmit diversity can complement receive diversity by adding an additional diversity gain and in situations where receiver diversity is not practical, transmit diversity alone delivers a comparable amount of diversity gain. Transmit Delay Diversity (DD) can be applied to systems employing the
DVB standard without receiver equipment modifications. Although transmit DD can
provide a gain in NLOS situations, it can introduce degradation in LOS situation. The aim of this thesis is to investigate the effectiveness in real-word applications of novel diversity techniques for broadcast transmitter networks. Tests involved laboratory experiments using a wireless MIMO channel emulator and the deployment of a field measurement campaign dedicated to driving, indoor and rooftop reception. The relationship between the diversity gain, the propagation environment and several parameters such as the transmit antenna separation, the receiver speed and the Forward Error Correction Codes (FEC) configuration are investigated. Results includes the effect of real-word parameter usually not modeled in the software simulation analysis, such as antenna radiation patterns and mutual coupling, scattering vegetation impact, non-Gaussian noise sources and receiver implementation. Moreover, a practical analysis of the effectiveness of experimental techniques to mitigate the loss due to transmit DD loss in rooftop reception is presented. The results of this thesis confirmed, completed and extended the existing predictions with real word measurement results
Interference Suppression in Massive MIMO VLC Systems
The focus of this dissertation is on the development and evaluation of methods and principles to mitigate interference in multiuser visible light communication (VLC) systems using several transmitters. All components of such a massive multiple-input multiple-output (MIMO) system are considered and transformed into a communication system model, while also paying particular attention to the hardware requirements of different modulation schemes. By analyzing all steps in the communication process, the inter-channel interference between users is identified as the most critical aspect. Several methods of suppressing this kind of interference, i.e. to split the MIMO channel into parallel single channels, are discussed, and a novel active LCD-based interference suppression principle at the receiver side is introduced as main aspect of this work. This technique enables a dynamic adaption of the physical channel: compared to solely software-based or static approaches, the LCD interference suppression filter achieves adaptive channel separation without altering the characteristics of the transmitter lights. This is especially advantageous in dual-use scenarios with illumination requirements. Additionally, external interferers, like natural light or transmitter light sources of neighboring cells in a multicell setting, can also be suppressed without requiring any control over them. Each user's LCD filter is placed in front of the corresponding photodetector and configured in such a way that only light from desired transmitters can reach the detector by setting only the appropriate pixels to transparent, while light from unwanted transmitters remains blocked. The effectiveness of this method is tested and benchmarked against zero-forcing (ZF) precoding in different scenarios and applications by numerical simulations and also verified experimentally in a large MIMO VLC testbed created specifically for this purpose
Improving Third-Party Relaying for LTE-A: A Realistic Simulation Approach
In this article we propose solutions to diverse conflicts that result from
the deployment of the (still immature) relay node (RN) technology in LTE-A
networks. These conflicts and their possible solutions have been observed by
implementing standard-compliant relay functionalities on the Vienna simulator.
As an original experimental approach, we model realistic RN operation, taking
into account that transmitters are not active all the time due to half-duplex
RN operation. We have rearranged existing elements in the simulator in a manner
that emulates RN behavior, rather than implementing a standalone brand-new
component for the simulator. We also study analytically some of the issues
observed in the interaction between the network and the RNs, to draw
conclusions beyond simulation observation.
The main observations of this paper are that: ) Additional time-varying
interference management steps are needed, because the LTE-A standard employs a
fixed time division between eNB-RN and RN-UE transmissions (typical relay
capacity or throughput research models balance them optimally, which is
unrealistic nowadays); ) There is a trade-off between the time-division
constraints of relaying and multi-user diversity; the stricter the constraints
on relay scheduling are, the less flexibility schedulers have to exploit
channel variation; and ) Thee standard contains a variety of parameters
for relaying configuration, but not all cases of interest are covered.Comment: 17 one-column pages, 9 figures, accepted for publication in IEEE ICC
2014 MW
Adaptive Baseband Pro cessing and Configurable Hardware for Wireless Communication
The world of information is literally at oneâs fingertips, allowing access to previously unimaginable amounts of data, thanks to advances in wireless communication. The growing demand for high speed data has necessitated theuse of wider bandwidths, and wireless technologies such as Multiple-InputMultiple-Output (MIMO) have been adopted to increase spectral efficiency.These advanced communication technologies require sophisticated signal processing, often leading to higher power consumption and reduced battery life.Therefore, increasing energy efficiency of baseband hardware for MIMO signal processing has become extremely vital. High Quality of Service (QoS)requirements invariably lead to a larger number of computations and a higherpower dissipation. However, recognizing the dynamic nature of the wirelesscommunication medium in which only some channel scenarios require complexsignal processing, and that not all situations call for high data rates, allowsthe use of an adaptive channel aware signal processing strategy to provide adesired QoS. Information such as interference conditions, coherence bandwidthand Signal to Noise Ratio (SNR) can be used to reduce algorithmic computations in favorable channels. Hardware circuits which run these algorithmsneed flexibility and easy reconfigurability to switch between multiple designsfor different parameters. These parameters can be used to tune the operations of different components in a receiver based on feedback from the digitalbaseband. This dissertation focuses on the optimization of digital basebandcircuitry of receivers which use feedback to trade power and performance. Aco-optimization approach, where designs are optimized starting from the algorithmic stage through the hardware architectural stage to the final circuitimplementation is adopted to realize energy efficient digital baseband hardwarefor mobile 4G devices. These concepts are also extended to the next generation5G systems where the energy efficiency of the base station is improved.This work includes six papers that examine digital circuits in MIMO wireless receivers. Several key blocks in these receiver include analog circuits thathave residual non-linearities, leading to signal intermodulation and distortion.Paper-I introduces a digital technique to detect such non-linearities and calibrate analog circuits to improve signal quality. The concept of a digital nonlinearity tuning system developed in Paper-I is implemented and demonstratedin hardware. The performance of this implementation is tested with an analogchannel select filter, and results are presented in Paper-II. MIMO systems suchas the ones used in 4G, may employ QR Decomposition (QRD) processors tosimplify the implementation of tree search based signal detectors. However,the small form factor of the mobile device increases spatial correlation, whichis detrimental to signal multiplexing. Consequently, a QRD processor capableof handling high spatial correlation is presented in Paper-III. The algorithm and hardware implementation are optimized for carrier aggregation, which increases requirements on signal processing throughput, leading to higher powerdissipation. Paper-IV presents a method to perform channel-aware processingwith a simple interpolation strategy to adaptively reduce QRD computationcount. Channel properties such as coherence bandwidth and SNR are used toreduce multiplications by 40% to 80%. These concepts are extended to usetime domain correlation properties, and a full QRD processor for 4G systemsfabricated in 28 nm FD-SOI technology is presented in Paper-V. The designis implemented with a configurable architecture and measurements show thatcircuit tuning results in a highly energy efficient processor, requiring 0.2 nJ to1.3 nJ for each QRD. Finally, these adaptive channel-aware signal processingconcepts are examined in the scope of the next generation of communicationsystems. Massive MIMO systems increase spectral efficiency by using a largenumber of antennas at the base station. Consequently, the signal processingat the base station has a high computational count. Paper-VI presents a configurable detection scheme which reduces this complexity by using techniquessuch as selective user detection and interpolation based signal processing. Hardware is optimized for resource sharing, resulting in a highly reconfigurable andenergy efficient uplink signal detector
- âŠ