Advances in Solid State Circuit Technologies

This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields

The Role of Recoverable and Non-Recoverable Defects in DC Electrical Aging of Highly Disordered Insulating Materials

Electrical insulation under high voltage can eventually fail, causing critical damage to electronics. Such electrostatic discharge (ESD) is the primary source of anomalies or failures on spacecraft due to charged particles from the Sun or planetary radiation belts accumulating in spacecraft insulators. Highvoltage direct current power distribution is another example of a growing industry that needs to estimate the operational lifetime of electrical insulation. My research compares laboratory tests of ESD events in common insulating materials to a physics-based model of breakdown. This model of breakdown is based on the approximation that there are two primary types of defects in structurally amorphous insulators. One of the two defect modes can switch on and off depending on the material temperature. This dual-defect model can be used to explain both ESD and less-destructive transient partial discharges. I show that the results of ESD tests agree reasonably well with the dual defect model. I also show that transient partial discharges, which are usually ignored during ESD tests, are closely related to the probability of catastrophic ESD occurring. Since many partial discharges are typically seen during one ESD test, this relationship suggests that the measurements of partial discharges could accelerate the testing needed to characterize the likelihood of ESD in insulating materials

Development of the readout electronics for the high luminosity upgrade of the CMS outer strip tracker

The High-luminosity upgrade of the LHC will deliver the dramatic increase in luminosity required for precision measurements and to probe Beyond the Standard Model theories. At the same time, it will present unprecedented challenges in terms of pileup and radiation degradation. The CMS experiment is set for an extensive upgrade campaign, which includes the replacement of the current Tracker with another all-silicon detector with improved performance and reduced mass. One of the most ambitious aspects of the future Tracker will be the ability to identify high transverse momentum track candidates at every bunch crossing and with very low latency, in order to include tracking information at the L1 hardware trigger stage, a critical and effective step to achieve triggers with high purity and low threshold. This thesis presents the development and the testing of the CMS Binary Chip 2 (CBC2), a prototype Application Specific Integrated Circuit (ASIC) for the binary front-end readout of silicon strip detectors modules in the Outer Tracker, which also integrates the logic necessary to identify high transverse momentum candidates by correlating hits from two silicon strip detectors, separated by a few millimetres. The design exploits the relation between the transverse momentum and the curvature in the trajectory of charged particles subject to the large magnetic field of CMS. The logic which follows the analogue amplification and binary conversion rejects clusters wider than a programmable maximum number of adjacent strips, compensates for the geometrical offset in the alignment of the module, and correlates the hits between the two sensor layers. Data are stored in a memory buffer before being transferred to an additional buffer stage and being serially read-out upon receipt of a Level 1 trigger. The CBC2 has been subject to extensive testing since its production in January 2013: this work reports the results of electrical characterization, of the total ionizing dose irradiation tests, and the performance of a prototype module instrumented with CBC2 in realistic conditions in a beam test. The latter is the first experimental demonstration of the Pt-selection principle central to the future of CMS. Several total-ionizing-dose tests highlighted no functional issue, but observed significant excess static current for doses <1 Mrad. The source of the excess was traced to static leakage current in the memory pipeline, and is believed to be a consequence of the high instantaneous dose delivered by the x-ray setup. Nevertheless, a new SRAM layout aimed at removing the leakage path was proposed for the CBC3. The results of single event upset testing of the chip are also reported, two of the three distinct memory circuits used in the chip were proven to meet the expected robustness, while the third will be replaced in the next iteration of the chip. Finally, the next version of the ASIC is presented, highlighting the additional features of the final prototype, such as half-strip resolution, additional trigger logic functionality, longer trigger latency and higher rate, and fully synchronous stub readout.Open Acces

Mod-5A Wind Turbine Generator Program Design Report. Volume 4: Drawings and Specifications, Book 1

The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator is documented. Volume 4 contains the drawings and specifications that were developed in preparation for building the MOD-5A wind turbine generator. This is the first of five books of volume four. It contains structural design criteria, generator step-up transformer specs, specs for design, fabrication and testing of the system, specs for the ground control enclosure, systems specs, slip ring specs, and control system specs

The 1991 International Aerospace and Ground Conference on Lightning and Static Electricity, volume 1

The proceedings of the 1991 International Aerospace and Ground Conference on Lightning and Static Electricity are reported. Some of the topics covered include: lightning, lightning suppression, aerospace vehicles, aircraft safety, flight safety, aviation meteorology, thunderstorms, atmospheric electricity, warning systems, weather forecasting, electromagnetic coupling, electrical measurement, electrostatics, aircraft hazards, flight hazards, meteorological parameters, cloud (meteorology), ground effect, electric currents, lightning equipment, electric fields, measuring instruments, electrical grounding, and aircraft instruments

Low-Temperature CO-Oxidation Catalysts for Long-Life CO2 Lasers

Low-temperature CO-oxidation catalysts are necessary for closed-cycle pulsed CO2 lasers as well as for other applications, including air purification. The papers presented in this volume discuss several such catalysts, including information on catalyst preparation, techniques for enhancing catalyst performance, laboratory and laser test results, and mechanistic considerations

Technology 2001: The Second National Technology Transfer Conference and Exposition, volume 2

Proceedings of the workshop are presented. The mission of the conference was to transfer advanced technologies developed by the Federal government, its contractors, and other high-tech organizations to U.S. industries for their use in developing new or improved products and processes. Volume two presents papers on the following topics: materials science, robotics, test and measurement, advanced manufacturing, artificial intelligence, biotechnology, electronics, and software engineering

Spacecraft Charging Technology, 1978

The interaction of the aerospace environment with spacecraft surfaces and onboard, high voltage spacecraft systems operating over a wide range of altitudes from low Earth orbit to geosynchronous orbit is considered. Emphasis is placed on control of spacecraft electric potential. Electron and ion beams, plasma neutralizers material selection, and magnetic shielding are among the topics discussed