Built-in self test of RF subsystems

textWith the rapid development of wireless and wireline communications, a variety of new standards and applications are emerging in the marketplace. In order to achieve higher levels of integration, RF circuits are frequently embedded into System on Chip (SoC) or System in Package (SiP) products. These developments, however, lead to new challenges in manufacturing test time and cost. Use of traditional RF test techniques requires expensive high frequency test instruments and long test time, which makes test one of the bottlenecks for reducing IC costs. This research is in the area of built-in self test technique for RF subsystems. In the test approach followed in this research, on-chip detectors are used to calculate circuits specifications, and data converters are used to collect the data for analysis by an on-chip processor. A novel on-chip amplitude detector has been designed and optimized for RF circuit specification test. By using on-chip detectors, both the system performance and specifications of the individual components can be accurately measured. On-chip measurement results need to be collected by Analog to Digital Converters (ADCs). A novel time domain, low power ADC has been designed for this purpose. The ADC architecture is based on a linear voltage controlled delay line. Using this structure results in a linear transfer function for the input dependent delay. The time delay difference is then compared to a reference to generate a digital code. Two prototype test chips were fabricated in commercial CMOS processes. One is for the RF transceiver front end with on-chip detectors; the other is for the test ADC. The 940MHz RF transceiver front-end was implemented with on-chip detectors in a 0.18 [micrometer] CMOS technology. The chips were mounted onto RF Printed Circuit Boards (PCBs), with tunable power supply and biasing knobs. The detector was characterized with measurements which show that the detector keeps linear performance over a wide input amplitude range of 500mV. Preliminary simulation and measurements show accurate transceiver performance prediction under process variations. A 300MS/s 6 bit ADC was designed using the novel time domain architecture in a 0.13 [micrometer] standard digital CMOS process. The simulation results show 36.6dB Signal to Noise Ratio (SNR), 34.1dB Signal to Noise and Distortion Ratio (SNDR) for 99MHz input, Differential Non-Linearity (DNL)<0.2 Least Significant Bit (LSB), and Integral Non-Linearity (INL)<0.5LSB. Overall chip power is 2.7mW with a 1.2V power supply. The built-in detector RF test was extended to a full transceiver RF front end test with a loop-back setup, so that measurements can be made to verify the benefits of the technique. The application of the approach to testing gain, linearity and noise figure was investigated. New detector types are also evaluated. In addition, the low-power delay-line based ADC was characterized and improved to facilitate gathering of data from the detector. Several improved ADC structures at the system level are also analyzed. The built-in detector based RF test technique enables the cost-efficient test for SoCs.Electrical and Computer Engineerin

Jitter measurement built-in self-test circuit for phase locked loops

Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2005.Includes bibliographical references (p. 77-79).This paper discusses the development of a new type of BIST circuit, the (VDL)2, with the purpose of measuring jitter in IBM's phase locked loops. The (VDL)2, which stands for Variable Vernier Digital Delay Locked Line, implements both cycle-to-cycle and phase jitter measurements, by using a digital delay locked loop and a 60 stage Vernier delay line. This achieves a nominal jitter resolution of 10 ps with a capture range of +/- 150 ps and does so in real time. The proposed application for this circuit is during manufacturing test of the PLL. The circuit is implemented in IBM's 90 nm process and was completed in the PLL and Clocking Development ASIC group at IBM Microelectronics in Essex Junction, Vermont as part of the VI-A program.by Brandon Ray Kam.M.Eng

TIME-DIFFERENCE CIRCUITS: METHODOLOGY, DESIGN, AND DIGITAL REALIZATION

This thesis presents innovations for a special class of circuits called Time Difference (TD) circuits. We introduce a signal processing methodology with TD signals that alters the target signal from a magnitude perspective to time interval between two time events and systematically organizes the primary TD functions abstracted from existing TD circuits and systems. The TD circuits draw attention from a broad range of application fields. In addition, highly evolved complementary metal-oxide-semiconductor (CMOS) technology suffers from various problems related to voltage and current amplitude signal processing methods. Compared to traditional analog and digital circuits, TD circuits bring several compelling features: high-resolution, high-throughput, and low-design complexity with digital integration capability. Further, the fabrication technology is advancing into the nanometer regime; the reduction in voltage headroom limits the performance of traditional analog/mixed-signal designs. All-digital design of time-difference circuit needs to be stressed to adapt to the low-cost, low-power, and high-portability applications. We focus on Time-to-Digital Converters (TDC), one of the crucial building blocks in TD circuits. A novel algorithmic architecture is proposed based on a binary search algorithm and validated with both simulation and fabricated silicon. An all-digital structure Time-difference Amplifier (TDA) is designed and implemented to make FPGA and other all-digital implementations for TDC and related TD circuits feasible. Besides, we propose an all-digital timing measurement circuit based on the process variation from CMOS fabrication: PVTMC, which achieves a high measurement resolution:

An Infrastructure IP for On-Chip Clock Jitter Measurement

Abstrac

A high speed serializer/deserializer design

A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design. A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption. A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset). With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage. A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit. The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications

Precise Timing of Digital Signals: Circuits and Applications

With the rapid advances in process technologies, the performance of state-of-the-art integrated circuits is improving steadily. The drive for higher performance is accompanied with increased emphasis on meeting timing constraints not only at the design phase but during device operation as well. Fortunately, technology advancements allow for even more precise control of the timing of digital signals, an advantage which can be used to provide solutions that can address some of the emerging timing issues. In this thesis, circuit and architectural techniques for the precise timing of digital signals are explored. These techniques are demonstrated in applications addressing timing issues in modern digital systems. A methodology for slow-speed timing characterization of high-speed pipelined datapaths is proposed. The technique uses a clock-timing circuit to create shifted versions of a slow-speed clock. These clocks control the data flow in the pipeline in the test mode. Test results show that the design provides an average timing resolution of 52.9ps in 0.18μm CMOS technology. Results also demonstrate the ability of the technique to track the performance of high-speed pipelines at a reduced clock frequency and to test the clock-timing circuit itself. In order to achieve higher resolutions than that of an inverter/buffer stage, a differential (vernier) delay line is commonly used. To allow for the design of differential delay lines with programmable delays, a digitally-controlled delay-element is proposed. The delay element is monotonic and achieves a high degree of transfer characteristics' (digital code vs. delay) linearity. Using the proposed delay element, a sub-1ps resolution is demonstrated experimentally in 0.18μm CMOS. The proposed delay element with a fixed delay step of 2ps is used to design a high-precision all-digital phase aligner. High-precision phase alignment has many applications in modern digital systems such as high-speed memory controllers, clock-deskew buffers, and delay and phase-locked loops. The design is based on a differential delay line and a variation tolerant phase detector using redundancy. Experimental results show that the phase aligner's range is from -264ps to +247ps which corresponds to an average delay step of approximately 2.43ps. For various input phase difference values, test results show that the difference is reduced to less than 2ps at the output of the phase aligner. On-chip time measurement is another application that requires precise timing. It has applications in modern automatic test equipment and on-chip characterization of jitter and skew. In order to achieve small conversion time, a flash time-to-digital converter is proposed. Mismatch between the various delay comparators limits the time measurement precision. This is demonstrated through an experiment in which a 6-bit, 2.5ps resolution flash time-to-digital converter provides an effective resolution of only 4-bits. The converter achieves a maximum conversion rate of 1.25GSa/s

A time-based approach for multi-GHz embedded mixed-signal characterization and measurement /

The increasingly more sophisticated systems that are nowadays implemented on a single chip are placing stringent requirements on the test industry. New test strategies, equipment, and methodologies need to be developed to sustain the constant increase in demand for consumer and communication electronics. Techniques for built-in-self-test (BIST) and design-for-test (DFT) strategies have been proven to offer more feasible and economical testing solutions.Previous works have been conducted to perform on-chip testing, characterization, and measurement of signals and components. The current thesis advances those techniques on many levels. In terms of performance, an increase of more than an order of magnitude in speed is achieved. 70-GHz (effective sampling) on-chip oscilloscope is reported, compared to 4-GHz and 10-GHz ones in previous state-of-the-art implementations. Power dissipation is another area where the proposed work offer a superior solution compared to previous alternatives. All the proposed circuits do not exceed a few milliWatts of power dissipation, while performing multi-GHz high-speed signal capture at a medium resolution. Finally, and possibly most importantly, all the proposed circuits for test rely on a different form of signal processing; the time-based approach. It is believed that this approach paves the path to a lot of new techniques and circuit design skills that can be investigated more deeply. As an integral part of the time-based processing approach for GHz signal capture, this thesis verifies the advantages of using time amplification. The use of such amplification in the time domain is materialized with experimental results from three specific integrated circuits achieving different tasks in GHz high-speed in-situ signal measurement and characterization. Advantages of using such time-based approach techniques, when combined with the use of a front-end time amplifier, include noise immunity, the use of synthesizable digital cells, and circuit building blocks that track the technology scaling in terms of area and speed

Formal Verification and In-Situ Test of Analog and Mixed-Signal Circuits

As CMOS technologies continuously scale down, designing robust analog and mixed-signal (AMS) circuits becomes increasingly difficult. Consequently, there are pressing needs for AMS design checking techniques, more specifically design verification and design for testability (DfT). The purpose of verification is to ensure that the performance of an AMS design meets its specification under process, voltage and temperature (PVT) variations and different working conditions, while DfT techniques aim at embedding testability into the design, by adding auxiliary circuitries for testing purpose. This dissertation focuses on improving the robustness of AMS designs in highly scaled technologies, by developing novel formal verification and in-situ test techniques. Compared with conventional AMS verification that relies more on heuristically chosen simulations, formal verification provides a mathematically rigorous way of checking the target design property. A formal verification framework is proposed that incorporates nonlinear SMT solving techniques and simulation exploration to efficiently verify the dynamic properties of AMS designs. A powerful Bayesian inference based technique is applied to dynamically tradeoff between the costs of simulation and nonlinear SMT. The feasibility and efficacy of the proposed methodology are demonstrated on the verification of lock time specification of a charge-pump PLL. The powerful and low-cost digital processing capabilities of today?s CMOS technologies are enabling many new in-situ test schemes in a mixed-signal environment. First, a novel two-level structure of GRO-PVDL is proposed for on-chip jitter testing of high-speed high-resolution applications with a gated ring oscillator (GRO) at the first level to provide a coarse measurement and a Vernier-style structure at the second level to further measure the residue from the first level with a fine resolution. With the feature of quantization noise shaping, an effective resolution of 0.8ps can be achieved using a 90nm CMOS technology. Second, the reconfigurability of recent all-digital PLL designs is exploited to provide in-situ output jitter test and diagnosis abilities under multiple parametric variations of key analog building blocks. As an extension, an in-situ test scheme is proposed to provide online testing for all-digital PLL based polar transmitters

A DLL Based Test Solution for 3D ICs

Integrated circuits (ICs) are rapidly changing and vertical integration and packaging strategies have already become an important research topic. 2.5D and 3D IC integrations have obvious advantages over the conventional two dimensional IC implementations in performance, capacity, and power consumption. A passive Si interposer utilizing Through-Silicon via (TSV) technology is used for 2.5D IC integration. TSV is also the enabling technology for 3D IC integration. TSV manufacturing defects can affect the performance of stacked devices and reduce the yield. Manufacturing test methodologies for TSVs have to be developed to ensure fault-free devices. This thesis presents two test methods for TSVs in 2.5D and 3D ICs utilizing Delay-Locked Loop (DLL) modules. In the test method developed for TSVs in 2.5D ICs, a DLL is used to determine the propagation delay for fault detection. TSV faults in 3D ICs are detected through observation of the control voltage of a DLL. The proposed test methods present a robust performance against Process, supply Voltage and Temperature (PVT) variations due to the inherent feedback of DLLs. 3D full-wave simulations are performed to extract circuit level models for TSVs and fragments of an interposer wires using HFSS simulation tools. The extracted TSV models are then used to perform circuit level simulations using ADS tools from Agilent. Simulation results indicate that the proposed test solution for TSVs can detect manufacturing defects affecting the TSV propagation delay