Blocker Tolerant Radio Architectures

Future radio platforms have to be inexpensive and deal with a variety of co- existence issues. The technology trend during the last few years is towards system- on-chip (SoC) that is able to process multiple standards re-using most of the digital resources. A major bottle-neck to this approach is the co-existence of these standards operating at different frequency bands that are hitting the receiver front-end. So the current research is focused on the power, area and performance optimization of various circuit building blocks of a radio for current and incoming standards. Firstly, a linearization technique for low noise amplifiers (LNAs) called, Robust Derivative Superposition (RDS) method is proposed. RDS technique is insensitive to Process Voltage and Temperature (P.V.T.) variations and is validated with two low noise transconductance amplifier (LNTA) designs in 0.18µm CMOS technology. Measurement results from 5 dies of a resistive terminated LNTA shows that the pro- posed method improves IM3 over 20dB for input power up to -18dBm, and improves IIP_(3) by 10dB. A 2V inductor-less broadband 0.3 to 2.8GHz balun-LNTA employing the proposed RDS linearization technique was designed and measured. It achieves noise figure of 6.5dB, IIP3 of 16.8dBm, and P1dB of 0.5dBm having a power consumption of 14.2mW. The balun LNTA occupies an active area of 0.06mm2. Secondly, the design of two high linearity, inductor-less, broadband LNTAs employing noise and distortion cancellation techniques is presented. Main design issues and the performance trade-offs of the circuits are discussed. In the fully differential architecture, the first LNTA covers 0.1-2GHz bandwidth and achieves a minimum noise figure (NFmin) of 3dB, IIP_(3) of 10dBm and a P_(1dB) of 0dBm while dissipating 30.2mW. The 2^(nd) low power bulk driven LNTA with 16mW power consumption achieves NFmin of 3.4dB, IIP3 of 11dBm and 0.1-3GHz bandwidth. Each LNTA occupy an active area of 0.06mm2 in 45nm CMOS. Thirdly, a continuous-time low-pass ∆ΣADC equipped with design techniques to provide robustness against loop saturation due to blockers is presented. Loop over- load detection and correction is employed to improve the ADC’s tolerance to blockers; a fast overload detector activates the input attenuator, maintaining the ADC in linear operation. To further improve ADC’s blocker tolerance, a minimally-invasive integrated low-pass filter that reduces the most critical adjacent/alternate channel blockers is implemented. An ADC prototype is implemented in a 90nm CMOS technology and experimentally it achieves 69dB dynamic range over a 20MHz bandwidth with a sampling frequency of 500MHz and 17.1mW of power consumption. The alternate channel blocker tolerance at the most critical frequency is as high as -5.5dBFS while the conventional feed-forward modulator becomes unstable at -23.5dBFS of blocker power. The proposed blocker rejection techniques are minimally-invasive and take less than 0.3µsec to settle after a strong agile blocker appears. Finally, a new radio partitioning methodology that gives robust analog and mixed signal radio development in scaled technology for SoC integration, and the co-design of RF FEM-antenna system is presented. Based on the proposed methodology, a CMOS RF front-end module (FEM) with power amplifier (PA), LNA and transmit/receive switch, co-designed with antenna is implemented. The RF FEM circuit is implemented in a 32nm CMOS technology. Post extracted simulations show a noise figure < 2.5dB, S_(21) of 14dB, IIP3 of 7dBm and P1dB of -8dBm for the receiver. Total power consumption of the receiver is 11.8mW from a 1V supply. On the trans- mitter side, PA achieves peak RF output power of 22.34dBm with peak power added efficiency (PAE) of 65% and PAE of 33% with linearization at -6dB power back off. Simulations show an efficiency of 80% for the miniaturized dipole antenna

Digitally-Modulated Transmitter for Wireless Communications

With the increased digital processing capabilities of sub-micron CMOS nodes, pushing the digital world towards the antenna is becoming attractive, enabling higher reconfigurability of the transmitter, therefore, more degrees of freedom to end-users. More specifically, by adopting an RF-DAC (DAC working at RF frequency) instead of the traditional Power Amplifier block allows for increased performance of the whole transmitter. Hence, a polar transmitter is being studied and an implementation in 130 nm CMOS node is expected

Efficient, High power Precision RF and mmWave Digital Transmitter Architectures

Digital transmitters offer several advantages over conventional analog transmitters such as reconfigurability, elimination of scaling-unfriendly, power hungry and bulky analog blocks and portability across technology. The rapid advancement of technology in CMOS processes also enables integration of complex digital signal processing circuitry on the same die as the digital transmitter to compensate for their non-idealities. The use of this digital assistance can, for instance, enable the use of highly efficient but nonlinear switching-class power amplifiers by compensating for their severe nonlinearity through digital predistortion. While this shift to digitally intensive transmitter architectures is propelled by the benefits stated above, several pressing challenges arise that vary in their nature depending on the frequency of operation - from RF to mmWave. Millimeter wave CMOS power amplifiers have traditionally been limited in output power due to the low breakdown voltage of scaled CMOS technologies and poor quality of on-chip passives. Moreover, high data-rates and efficient spectrum utilization demand highly linear power amplifiers with high efficiency under back-off. However, linearity and high efficiency are traditionally at odds with each other in conventional power amplifier design. In this dissertation, digital assistance is used to relax this trade-off and enable the use of state-of-the-art switching class power amplifiers. A novel digital transmitter architecture which simultaneously employs aggressive device-stacking and large-scale power combining for watt-class output power, dynamic load modulation for linearization, and improved efficiency under back-off by supply-switching and load modulation is presented. At RF frequencies, while the problem of watt-class power amplification has been long solved, more pressing challenges arise from the crowded spectrum in this regime. A major drawback of digital transmitters is the absence of a reconstruction filter after digital-to-analog conversion which causes the baseband quantization noise to get upconverted to RF and amplified at the output of the transmitter. In high power transmitters, this upconverted noise can be so strong as to prevent their use in FDD systems due to receiver desensitization or impose stringent coexistence challenges. In this dissertation, new quantization noise suppression techniques are presented which, for the first time, contribute toward making watt-class fully-integrated digital RF transmitters a viable alternative for FDD and coexistence scenarios. Specifically, the techniques involve embedding a mixed-domain multi-tap FIR filter within highly-efficient watt-class switching power amplifiers to suppress quantization noise, enhancing the bandwidth of noise suppression, enabling tunable location of suppression and overcoming the limitations of purely digital-domain filtering techniques for quantization noise

Architectures and Integrated Circuits for Efficient, High-power "Digital'' Transmitters for Millimeter-wave Applications

This thesis presents architectures and integrated circuits for the implementation of energy-efficient, high-power "digital'' transmitters to realize high-speed long-haul links at millimeter-wave frequencies in nano-scale silicon-based processes