Dual-band implantable antennas for medical telemetry: a fast design methodology and validation for intra-cranial pressure monitoring

WOS:000323538100010 (Nº de Acesso Web of Science)In this study, we suggest and experimentally validate a methodology for fast and optimized design of dual-band implantable antennas for medical telemetry (MICS, 402-405 MHz, and ISM, 2400-2480 MHz). The methodology aims to adjust the design of a parametric dual-band antenna model towards optimally satisfying the requirements imposed by the antenna-fabrication procedure and medical application in hand. Design is performed in a systematic, fast, and accurate way. To demonstrate its effectiveness, the proposed methodology is applied to optimize the parametric antenna model for intra-cranial pressure (ICP) monitoring given a specific antenna-fabrication procedure. For validation purposes, a prototype of the optimized antenna is fabricated and experimentally tested. The proposed antenna is further evaluated within a 13-tissue anatomical head model in terms of resonance, radiation, and safety performance for ICP monitoring. Extensive parametric studies of the optimized antenna are, finally, performed. Feasibility of the proposed parametric antenna model to be optimally re-adjusted for various scenarios is demonstrated, and generic guidelines are provided for implantable antenna design. Dual-band operation is targeted to ensure energy autonomy for the implant. Finite Element (FE) and Finite Difference Time Domain (FDTD) simulations are carried out in homogeneous rectangular and anatomical head tissue models, respectively

A Dual-Band Compact Integrated Rectenna for Implantable Medical Devices

This work describes a dual band compact fully integrated rectenna circuit for implantable medical devices. The implantable rectenna circuit consists of tunnel diode 10×10µm2 QW-ASPAT (Quantum Well Asymmetric Spacer Tunnel Layer diode) was used as the rectifier due to its temperature insensitivity and non-linearity compared with conventional SBD diodes. A miniaturized dual band implantable folded dipole antenna with multiple L-shaped conducting sections for operation in the WMTS band is 1.5GHz and ISM band of 5.8GHz. High dielectric constant material Gallium Arsenide (εr=12.94) and folded geometry helps to design compact antennas with a small footprint of 2.84mm3 (4.5×1×0.63) mm3. Four-layer human tissue model was used, where the antenna was implanted in the skin model at depth of 2mm. The 10-dB impedance bandwidths of the proposed compact antenna at 1.5GHz and 5.8GHz are 227MHz (1.4-1.63GHz) with S11 is -22.6dB and 540MHz (5.47-6.02GHz) with S11 is -23.1dB, whereas gains are -36.9dBi, and -24.3dBi, respectively. The output DC voltage and power of the rectenna using two stage rectifiers are twice that produced by the single stage at input RF power of 10dBm

A Dual-Band Compact Integrated Rectenna for Implantable Medical Devices

This work describes a dual band compact fully integrated rectenna circuit for implantable medical devices (IMDs). The implantable rectenna circuit consists of tunnel diode 10×10μm2 QW-ASPAT (Quantum Well Asymmetric Spacer Tunnel Layer diode) was used as the RF-DC rectifier due to its temperature insensitivity and nonlinearity compared with conventional SBD diode. SILVACO atlas software is used to design and simulate 100μm2 QW InGaAs ASPAT diode. A miniaturized dual band implantable folded dipole antenna with multiple L-shaped conducting sections is designed using CST microwave suits for operation in the WMTS band is 1.5GHz and ISM band of 5.8GHz. High dielectric constant material Gallium Arsenide (εr=12.94) and folded geometry helps to design compact antennas with a small footprint of 2.84mm3 (1×4.5×0.63) mm3. Four-layer human tissue model was used, where the antenna was implanted in the skin model at depth of 2mm. The 10-dB impedance bandwidth of the proposed compact antenna at 1.5GHz and 5.8GHz are 227MHz (1.4-1.63GHz) with S11 is -22.6dB and 540MHz (5.47-6.02GHz) with S11 is -23.1dB, whereas gains are -36.9dBi, and -24.3dBi, respectively. The output DC voltage and power of the rectenna using two stage voltage doubler rectifier (VDR) are twice that produced by the single stage at input RF power of 10dBm

Implantable antennas for bio-medical applications

Biomedical telemetry has gained a lot of attention with the development in the healthcare industry. This technology has made it feasible to monitor the physiological signs of patient remotely without traditional hospital appointments and follow up routine check-ups. Implantable Medical Devices(IMDs) play an important role to monitor the patients through wireless telemetry. IMDs consist of nodes and implantable sensors in which antenna is a major component. The implantable sensors suffer a lot of limitations. Various factors need to be considered for the implantable sensors such as miniaturization, patient safety, bio-compatibility, low power consumption, lower frequency band of operation and dual-band operation to have a robust and continuous operation. The selection of the antenna is a challenging task in implantable sensor design as it dictates performance of the whole implant. In this paper a critical review on implantable antennas for biomedical applications is presented

On-body wearable repeater as a data link relay for in-body wireless implants

Wireless medical devices implanted at different locations in the human body have a wide application range. Yet, high-data-rate communication in the 2.4-GHz Industrial, Scientific, and Medical band suffers from high in-body attenuation loss. Link improvement cannot be obtained by simply increasing transmit power, as battery life is limited and in-body absorption has to remain low. To overcome these problems, a flexible on-body textile patch antenna, robustly matched directly to the human body, is designed and developed as part of a wearable repeater, enhancing communication with implanted wireless devices. This receive antenna, which can cope with different morphologies and patient movements, enables reliable high data rate and low-power communication links with an implant. A data link measurement is performed for the on-body repeater system placed on the human torso, relaying the signals to nearby medical equipment, without wired connection to the patient. The performance of the data link is experimentally assessed in different measurement scenarios. For a repeater system relying on simple analog amplification, which is low-cost, energy-efficient, and can be fully integrated into clothing, excellent results are obtained, with an average measured signal-to-noise ratio of 33 dB for tissue depths up to 85 mm

Improved reception of in-body signals by means of a wearable multi-antenna system

High data-rate wireless communication for in-body human implants is mainly performed in the 402-405 MHz Medical Implant Communication System band and the 2.45 GHz Industrial, Scientific and Medical band. The latter band offers larger bandwidth, enabling high-resolution live video transmission. Although in-body signal attenuation is larger, at least 29 dB more power may be transmitted in this band and the antenna efficiency for compact antennas at 2.45 GHz is also up to 10 times higher. Moreover, at the receive side, one can exploit the large surface provided by a garment by deploying multiple compact highly efficient wearable antennas, capturing the signals transmitted by the implant directly at the body surface, yielding stronger signals and reducing interference. In this paper, we implement a reliable 3.5 Mbps wearable textile multi-antenna system suitable for integration into a jacket worn by a patient, and evaluate its potential to improve the In-to-Out Body wireless link reliability by means of spatial receive diversity in a standardized measurement setup. We derive the optimal distribution and the minimum number of on-body antennas required to ensure signal levels that are large enough for real-time wireless endoscopy-capsule applications, at varying positions and orientations of the implant in the human body

Wireless body sensor networks for health-monitoring applications

This is an author-created, un-copyedited version of an article accepted for publication in Physiological Measurement. The publisher is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at http://dx.doi.org/10.1088/0967-3334/29/11/R01