Models for reducing power consumption in CPLD and FPGA devices

Usage of programmable logic devices PLD has increased in the latest years because of the ability to quickly implement complex types of electronic systems while reducing cost and time of synthesis. This technology enables dynamic reconfiguration of different applications according to specific requirements. Also, power consumption and its loss is becoming an increasingly important requirement in the design of systems for portable applications fed by batteries. Other factors to be taken into account in the consumption of power are elements that are used for manufacturing, packaging, and cooling systems. Power consumption must be taken into consideration especially for wireless applications where battery technologies provide power 20 W/h and voltage 1.2 volts. Despite improvements in battery technology, the development of methods for reducing power consumption plays a decisive role in portable applications. Therefore, modeling of power consumption has become a requirement with the highest impact in the performance of FPGA elements. Despite generated models of the different manufacturers of these elements, this article will appear comparisons of models based on experimental measurements performed on both CPLD and FPGA elements. Based on these models is selected to simulate a system that will be implemented in two elements and see how reduced power consumption, without affecting system performance. Experimental results show that FPGA elements have better performance and significantly reduce the power consumption

Performance Comparison of Static CMOS and Domino Logic Style in VLSI Design: A Review

Of late, there is a steep rise in the usage of handheld gadgets and high speed applications. VLSI designers often choose static CMOS logic style for low power applications. This logic style provides low power dissipation and is free from signal noise integrity issues. However, designs based on this logic style often are slow and cannot be used in high performance circuits. On the other hand designs based on Domino logic style yield high performance and occupy less area. Yet, they have more power dissipation compared to their static CMOS counterparts. As a practice, designers during circuit synthesis, mix more than one logic style judiciously to obtain the advantages of each logic style. Carefully designing a mixed static Domino CMOS circuit can tap the advantages of both static and Domino logic styles overcoming their own short comings

EFFICIENT HARDWARE PRIMITIVES FOR SECURING LIGHTWEIGHT SYSTEMS

In the era of IoT and ubiquitous computing, the collection and communication of sensitive data is increasingly being handled by lightweight Integrated Circuits. Efficient hardware implementations of crytographic primitives for resource constrained applications have become critical, especially block ciphers which perform fundamental operations such as encryption, decryption, and even hashing. We study the efficiency of block ciphers under different implementation styles. For low latency applications that use unrolled block cipher implementations, we design a glitch filter to reduce energy consumption. For lightweight applications, we design a novel architecture for the widely used AES cipher. The design eliminates inefficiencies in data movement and clock activity, thereby significantly improving energy efficiency over state-of-the-art architectures. Apart from efficiency, vulnerability to implementation attacks are a concern, which we mitigate by our randomization capable lightweight AES architecture. We fabricate our designs in a commercial 16nm FinFET technology and present measured testchip data on energy consumption and side channel resistance. Finally, we address the problem of supply chain security by using image processing techniques to extract fingerprints from surface texture of plastic IC packages for IC authentication and counterfeit prevention. Collectively these works present efficient and cost effective solutions to secure lightweight systems

Hazards, Critical Races, and Metastability

The various modes of failure of asynchronous sequential logic circuits due to timing problems are considered. These are hazards, critical races and metastable states. It is shown that there is a mechanism common to all forms of hazards and to metastable states. A similar mechanism, with added complications, is shown to characterize critical races. Means for defeating various types of hazards and critical races through the use of one sided delay constraints are introduced. A method is described for determining from a flow table situations in which metastable states may be entered. A circuit technique for defeating metastability problems in self timed systems is presented. It is shown that the use of simulation for verifying the correctness of a circuit with given bounds on the branch delays cannot be relied upon to expose all timing problems. An example is presented that refutes the conjecture that replacing pure delays with inertial delays can only eliminate glitches. Key Words asynchronous, critical race, delays, dynamic hazards, essential hazards, inertial delays, metastability, pure delays, sequential logic, timing problems, timing simulation

Power reduction techniques for memory elements

High performance and computational capability in the current generation processors are made possible by small feature sizes and high device density. To maintain the current drive strength and control the dynamic power in these processors, simultaneous scaling down of supply and threshold voltages is performed. High device density and low threshold voltages result in an increase in the leakage current dissipation. Large on chip caches are integrated onto the current generation processors which are becoming a major contributor to total leakage power. In this work, a novel methodology is proposed to minimize the leakage power and dynamic power. The proposed static power reduction technique, GALEOR (GAted LEakage transistOR), introduces stacks by placing high threshold voltage transistors and consists of inherent control logic. The proposed dynamic power reduction technique, adaptive phase tag cache, achieves power savings through varying tag size for a design window. Testing and verification of the proposed techniques is performed on a two level cache system. Power delay squared product is used as a metric to measure the effectiveness of the proposed techniques. The GALEOR technique achieves 30% reduction when implemented on CMOS benchmark circuits and an overall leakage savings of 9% when implemented on the two level cache systems. The proposed dynamic power reduction technique achieves 10% savings when implemented on individual modules of the two level cache and an overall savings of 3% when implemented on the entire two level cache system

IMPROVEMENTS IN INVERTER MODELING AND CONTROL

In this dissertation, the generalized averaging method models for inverters, reactive power control methods for photovoltaic inverters, and a noise immunity improvement for hybrid position observers for brushless dc motor drives are studied. Models of inverters and other converters based on averaging have been widely used in numerous simulation applications. Generalized averaging can be applied to model both average and switching behavior of converters while retaining the faster run times associated with average-value models. Herein, generalized average models for single- and three-phase pulse width modulation inverters are proposed. The modulation signal for the proposed model could be either a sinusoidal waveform without high order harmonics or a sinusoidal waveform with third-harmonic injection. And this generalized average models also can apply for modeling three-phase pulse width modulation inverters with varying modulation signal frequency in the reference frame. These models are based on a quasi-Fourier series representation of the switching functions that includes fundamental and switching frequency components as well as sideband components of the switching frequency. The proposed models are demonstrated both in simulation and experimentally and are found to accurately portray both the fundamental and the switching behavior of the inverter. In particular, the use of sideband components allows accurate representation of the variation in switching ripple magnitude that occurs in the steady state. The generalized average models are found to have simulation run times that are significantly faster than those associated with detailed models. Therefore, the proposed generalized average models are suitable for simulation applications in which both accuracy (including the switching behavior) and fast run times are required (e.g., long simulation times, systems with multiple converters, and repeated simulations). Variations in the output power of intermittent renewable sources can cause significant fluctuations of distribution system voltage magnitudes. Reactive power control methods that employ the reactive power capability of photovoltaic three-phase inverters to mitigate these fluctuations are proposed. These control methods cause the three-phase inverters to substitute reactive output power for real output power when fluctuations in the solar power are experienced, allowing the fluctuations to be controlled. Performance metrics for assessing the ability of these controllers to perform this mitigation are defined. The controllers are examined using the IEEE 123-bus feeder distribution system, and it is found that the controllers can effectively mitigate voltage magnitude fluctuations and that the appropriate choice of controller depends on the performance metrics of interest. Finally, a noise immunity improvement for hybrid position observers for brushless dc motor drives is proposed. A finite state machine is used to detect Hall-effect sensor transitions to determine if these transitions are true transitions or the result of momentary glitches. This filter causes a delay in the detection of the Hall-effect sensors that is compensated in the proposed observer. The proposed observer is compared in simulations with the original hybrid position observer under both non-noisy and noisy conditions for both constant and variable speed operation, and it has good performance even under high noise and variable speed conditions

CAD Tool Design for NCL and MTNCL Asynchronous Circuits

This thesis presents an implementation of a method developed to readily convert Boolean designs into an ultra-low power asynchronous design methodology called MTNCL, which combines multi-threshold CMOS (MTCMOS) with NULL Convention Logic (NCL) systems. MTNCL provides the leakage power advantages of an all high-Vt implementation with a reasonable speed penalty compared to the all low-Vt implementation, and has negligible area overhead. The proposed tool utilizes industry-standard CAD tools. This research also presents an Automated Gate-Level Pipelining with Bit-Wise Completion (AGLPBW) method to maximize throughput of delay-insensitive full-word pipelined NCL circuits. These methods have been integrated into the Mentor Graphics and Synopsis CAD tools, using a C-program, which performs the majority of the computations, such that the method can be easily ported to other CAD tool suites. Both methods have been successfully tested on circuits, including a 4-bit × 4-bit multiplier, an unsigned Booth2 multiplier, and a 4-bit/8-operation arithmetic logic unit (ALU

Analysis and Design of Resilient VLSI Circuits

The reliable operation of Integrated Circuits (ICs) has become increasingly difficult to achieve in the deep sub-micron (DSM) era. With continuously decreasing device feature sizes, combined with lower supply voltages and higher operating frequencies, the noise immunity of VLSI circuits is decreasing alarmingly. Thus, VLSI circuits are becoming more vulnerable to noise effects such as crosstalk, power supply variations and radiation-induced soft errors. Among these noise sources, soft errors (or error caused by radiation particle strikes) have become an increasingly troublesome issue for memory arrays as well as combinational logic circuits. Also, in the DSM era, process variations are increasing at an alarming rate, making it more difficult to design reliable VLSI circuits. Hence, it is important to efficiently design robust VLSI circuits that are resilient to radiation particle strikes and process variations. The work presented in this dissertation presents several analysis and design techniques with the goal of realizing VLSI circuits which are tolerant to radiation particle strikes and process variations. This dissertation consists of two parts. The first part proposes four analysis and two design approaches to address radiation particle strikes. The analysis techniques for the radiation particle strikes include: an approach to analytically determine the pulse width and the pulse shape of a radiation induced voltage glitch in combinational circuits, a technique to model the dynamic stability of SRAMs, and a 3D device-level analysis of the radiation tolerance of voltage scaled circuits. Experimental results demonstrate that the proposed techniques for analyzing radiation particle strikes in combinational circuits and SRAMs are fast and accurate compared to SPICE. Therefore, these analysis approaches can be easily integrated in a VLSI design flow to analyze the radiation tolerance of such circuits, and harden them early in the design flow. From 3D device-level analysis of the radiation tolerance of voltage scaled circuits, several non-intuitive observations are made and correspondingly, a set of guidelines are proposed, which are important to consider to realize radiation hardened circuits. Two circuit level hardening approaches are also presented to harden combinational circuits against a radiation particle strike. These hardening approaches significantly improve the tolerance of combinational circuits against low and very high energy radiation particle strikes respectively, with modest area and delay overheads. The second part of this dissertation addresses process variations. A technique is developed to perform sensitizable statistical timing analysis of a circuit, and thereby improve the accuracy of timing analysis under process variations. Experimental results demonstrate that this technique is able to significantly reduce the pessimism due to two sources of inaccuracy which plague current statistical static timing analysis (SSTA) tools. Two design approaches are also proposed to improve the process variation tolerance of combinational circuits and voltage level shifters (which are used in circuits with multiple interacting power supply domains), respectively. The variation tolerant design approach for combinational circuits significantly improves the resilience of these circuits to random process variations, with a reduction in the worst case delay and low area penalty. The proposed voltage level shifter is faster, requires lower dynamic power and area, has lower leakage currents, and is more tolerant to process variations, compared to the best known previous approach. In summary, this dissertation presents several analysis and design techniques which significantly augment the existing work in the area of resilient VLSI circuit design

Energy Aware Design and Analysis for Synchronous and Asynchronous Circuits

Power dissipation has become a major concern for IC designers. Various low power design techniques have been developed for synchronous circuits. Asynchronous circuits, however. have gained more interests recently due to their benefits in lower noise, easy timing control, etc. But few publications on energy reduction techniques for asynchronous logic are available. Power awareness indicates the ability of the system power to scale with changing conditions and quality requirements. Scalability is an important figure-of-merit since it allows the end user to implement operational policy. just like the user of mobile multimedia equipment needs to select between better quality and longer battery operation time. This dissertation discusses power/energy optimization and performs analysis on both synchronous and asynchronous logic. The major contributions of this dissertation include: 1 ) A 2-Dimensional Pipeline Gating technique for synchronous pipelined circuits to improve their power awareness has been proposed. This technique gates the corresponding clock lines connected to registers in both vertical direction (the data flow direction) and horizontal direction (registers within each pipeline stage) based on current input precision. 2) Two energy reduction techniques, Signal Bypassing & Insertion and Zero Insertion. have been developed for NCL circuits. Both techniques use Nulls to replace redundant Data 0\u27s based on current input precision in order to reduce the switching activity while Signal Bypassing & Insertion is for non-pipelined NCI, circuits and Zero Insertion is for pipelined counterparts. A dynamic active-bit detection scheme is also developed as an expansion. 3) Two energy estimation techniques, Equivalent Inverter Modeling based on Input Mapping in transistor-level and Switching Activity Modeling in gate-level, have been proposed. The former one is for CMOS gates with feedbacks and the latter one is for NCL circuits