Maximum performance of piezoelectric energy harvesters when coupled to interface circuits

This paper presents a complete optimization of a piezoelectric vibration energy harvesting system, including a piezoelectric transducer, a power conditioning circuit with full semiconductor device models, a battery and passive components. To the authors awareness, this is the first time and all of these elements have been integrated into one optimization. The optimization is done within a framework, which models the combined mechanical and electrical elements of a complete piezoelectric vibration energy harvesting system. To realize the optimization, an optimal electrical damping is achieved using a single-supply pre-biasing circuit with a buck converter to charge the battery. The model is implemented in MATLAB and verified in SPICE. The results of the full system model are used to find the mechanical and electrical system parameters required to maximize the power output. The model, therefore, yields the upper bound of the output power and the system effectiveness of complete piezoelectric energy harvesting systems and, hence, provides both a benchmark for assessing the effectiveness of existing harvesters and a framework to design the optimized harvesters. It is also shown that the increased acceleration does not always result in increased power generation as a larger damping force is required, forcing a geometry change of the harvester to avoid exceeding the piezoelectric breakdown voltage. Similarly, increasing available volume may not result in the increased power generation because of the difficulty of resonating the beam at certain frequencies whilst utilizing the entire volume. A maximum system effectiveness of 48% is shown to be achievable at 100 Hz for a 3.38-cm3 generator

A Hybrid Vibration Powered Microelectromechanical Strain Gauge

This paper reports the demonstration of an ultra-low power MEMS-CMOS oscillator for strain sensing, powered by a miniature piezoelectric vibration energy harvester (VEH). The employment of the Pierce oscillator topology in a MEMS-CMOS oscillator allows for minimisation of the power requirement to as low as 1.1 µW under ideal conditions. A VEH prototype, developed with hard PZT on a stainless steel substrate (∼0.4 cm3 practical operational volume), is able to deliver a typical average power of 187 µW at 11.4 ms−2 and 514 Hz. Some of the practical challenges associated with the integration of the harvester and the MEMS sensor have also been explored, which helps to lay the foundation for realising net-zero-power strain sensors.This work was supported by EPSRC (grants: EP/K000314/1 and EP/L010917/1).This is the author accepted manuscript. The final version is available from IEEE via http://dx.doi.org/10.1109/JSEN.2015.247929

Micro-Engineered Devices for Motion Energy Harvesting

Published versio

Piezoelectric energy harvesting solutions

This paper reviews the state of the art in piezoelectric energy harvesting. It presents the basics of piezoelectricity and discusses materials choice. The work places emphasis on material operating modes and device configurations, from resonant to non-resonant devices and also to rotational solutions. The reviewed literature is compared based on power density and bandwidth. Lastly, the question of power conversion is addressed by reviewing various circuit solutions

Real World Assessment of an Auto-parametric Electromagnetic Vibration Energy Harvester

The convention within the eld of vibration energy harvesting (VEH) has revolved around designing resonators with natural frequencies that match single fixed frequency sinusoidal input. However, real world vibrations can be random, multi-frequency, broadband and time-varying in nature. Building upon previous work on auto-parametric resonance, the fundamentally different approach allows multiple axes vibration and has the potential to achieve higher power density as well as wider operational frequency bandwidth. This paper presents the power response of a packaged auto-parametric VEH prototype (practical operational volume 126 cm^3) towards various real world vibration sources including vibration of a bridge, a compressor motor as well as an automobile. At auto-parametric resonance (driven at 23.5 Hz and 1 grms), the prototype can output a peak of 78.9 mW and 4.5 Hz of -3dB bandwidth. Furthermore, up to ~1 mW of average power output was observed from the harvester on the Forth Road Bridge. The harvested electrical energy from various real world sources were used to power up a power conditioning circuit, a wireless sensor mote, a MEMS (micro-electromechanical system) accelerometer and other low power sensors. This demonstrates the concept of self-sustaining vibration-powered wireless sensor systems in real world scenarios, to potentially realise maintenance-free autonomous structural health and condition monitoring.This work was supported by EPSRC (grant EP/L010917/1) and the Cambridge Centre for Smart Infrastructure and Construction

Power electronic interfaces for piezoelectric energy harvesters

Motion-driven energy harvesters can replace batteries in low power wireless sensors, however selection of the optimal type of transducer for a given situation is difficult as the performance of the complete system must be taken into account in the optimisation. In this thesis, a complete piezoelectric energy harvester system model including a piezoelectric transducer, a power conditioning circuit, and a battery, is presented allowing for the first time a complete optimisation of such a system to be performed. Combined with previous work on modelling an electrostatic energy harvesting system, a comparison of the two transduction methods was performed. The results at 100 Hz indicate that for small MEMS devices at low accelerations, electrostatic harvesting systems outperform piezoelectric but the opposite is true as the size and acceleration increases. Thus the transducer type which achieves the best power density in an energy harvesting system for a given size, acceleration and operating frequency can be chosen. For resonant vibrational energy harvesting, piezoelectric transducers have received a lot of attention due to their MEMS manufacturing compatibility with research focused on the transduction method but less attention has been paid to the output power electronics. Detailed design considerations for a piezoelectric harvester interface circuit, known as single-supply pre-biasing (SSPB), are developed which experimentally demonstrate the circuit outperforming the next best known interface's theoretical limit. A new mode of operation for the SSPB circuit is developed which improves the power generation performance when the piezoelectric material properties have degraded. A solution for tracking the maximum power point as the excitation changes is also presented.Open Acces

A Nail-Size Piezoelectric Energy Harvesting System Integrating a MEMS Transducer and a CMOS SSHI Circuit

Piezoelectric vibration energy harvesting has drawn much interest to power distributed wireless sensor nodes for Internet of Things (IoT) applications where ambient kinetic energy is available. For certain applications, the harvesting system should be small and able to generate sufficient output power. Standard rectification topologies such as the full-bridge rectifier are typically inefficient when adapted to power conditioning from miniaturized harvesters. Therefore, active rectification circuits have been researched to improve overall power conversion efficiency, and meet both the output power and miniaturization requirements while employing a MEMS harvester. In this paper, a MEMS piezoelectric energy harvester is designed and cointegrated with an active synchronized switch harvesting on inductor (SSHI) rectification circuit designed in a CMOS process to achieve high output power for system miniaturization. The system is fully integrated on a nail-size board, which is ready to provide a stable DC power for low-power mini sensors. A MEMS energy harvester of 0.005 cm3 size, co-integrated with the CMOS conditioning circuit, outputs a peak rectified DC power of 40.6 µW and achieves a record DC power density of 8.12 mW/cm3 when compared to state-of-the-art harvesters

Analysis on One-Stage SSHC Rectifier for Piezoelectric Vibration Energy Harvesting

Conventional SSHI (synchronized switch harvesting on inductor) has been believed to be one of the most efficient interface circuits for piezoelectric vibration energy harvesting systems. It employs an inductor and the resulting RLC loop to synchronously invert the charge across the piezoelectric material to avoid charge and energy loss due to charging its internal capacitor ($C_P$). The performance of the SSHI circuit greatly depends on the inductor and a large inductor is often needed; hence significantly increases the volume of the system. An efficient interface circuit using a synchronous charge inversion technique, named as SSHC, was proposed recently. The SSHC rectifier utilizes capacitors, instead of inductors, to flip the voltage across the harvester. For a one-stage SSHC rectifier, one single intermediate capacitor ($C_T$) is employed to temporarily store charge flowed from $C_P$ and inversely charge $C_P$ to perform the charge inversion. In previous studies, the voltage flip efficiency achieves 1/3 when $C_T = C_P$. This paper presents that the voltage flip efficiency can be further increased to approach 1/2 if $C_T$ is chosen to be much larger than $C_P$