Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz

This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d

RF system model for In-band full duplex communications

Abstract. In recent years by increasing the demands for communication services various technologies are examined in order to improve the throughput and spectrum efficiency of the wireless communication systems. For improving the performance a communication network, system deficiencies such as transmitter and receiver impairments need to be removed or compensated. One way to improve the network efficiency is to employ full duplex technology. Full duplex technology doubles the network capacity compared to the case when typical frequency division duplexing (FDD) or time division duplexing (TDD) are employed in a transceiver design. Although full duplex (FD) technology has enhanced the performance of the radio communication devices, the main challenge in full duplex communication is the leaking self-interference signal from the transmitter to the receiver. Different methods are employed to suppress the self-interference signal in digital and analog domains which are categorized as passive or active cancellations. These techniques are discussed in this thesis in order to understand from which point in the propagation path, the required signal for cancellation can be taken and how those techniques are employed in digital and analog domains. For having a good self-interference cancellation (SIC) both analog and digital cancellation techniques are needed since typical digital suppression method is low complex and somewhat limited. In this thesis, first we start with discussing about the full duplex technology and the reason why it has become popular in recent years and later full duplex deficiencies are examined. In the following chapters different cancellation methods are introduced and some results are provided in Chapter 5

Circuits and architectures for the implementation of broadband channelizers

Broadband spectrum channelizers sub-divide a broadband input spectrum into multiple sub-bands, where each of the sub-bands is down-converted and further processed at baseband. These designs can help to relax baseband design specifications. For example, baseband analog-to-digital converters (ADCs) that process the sub-bands at the channelizer output see only a part of the incident spectrum. The sampling frequency, and potentially the dynamic range of each sub-band ADC can thus be relaxed, compared to the case where a single ADC is used to digitize the full spectrum. Spectrum channelizers can be used for multiple applications. These designs can be used as general-purpose hybrid frequency-and-time domain ADCs. The designs can also be employed for spectrum analysis, as well as for wireless communication applications. In this dissertation, two circuit techniques for the implementation of broadband channelizers are proposed. A frequency-translational feedback-based interference canceler for attenuating large interferers at the output of the front-end low-noise amplifier (LNA) of a channelizer is shown. The design uses harmonic rejection mixers (HRMs) with embedded frequency synthesis capability. While channelizers reduce the bandwidth and potentially the dynamic range of the baseband ADCs, the analog signal paths in the channelizer can be broadband. Consequently the dynamic range required of the analog section of a sub-band path can still be limited by the presence of large signals in other, potentially distant parts of the spectrum. The demonstrated design is useful for relaxing the dynamic range requirement of the analog section that follows the front-end LNA in a channelizer. Reduction of the harmonic response and the frequency synthesizer tuning-range is also achieved in this design. Second, a two-stage HRM is proposed which shares the same bias current between the RF and baseband stages, thus reducing the power consumption. Issues arising from bias-current sharing, such as the 1/f noise of the RF stage and potential degradation of the 2nd harmonic response are identified, and circuit techniques are introduced to mitigate these potential degradation mechanisms.Electrical and Computer Engineerin

High-speed Time-interleaved Digital-to-Analog Converter (TI-DAC) for Self-Interference Cancellation Applications

Nowadays, the need for higher data-rate is constantly growing to enhance the quality of the daily communication services. The full-duplex (FD) communication is exemplary method doubling the data-rate compared to half-duplex one. However, part of the strong output signal of the transmitter interferes to the receiver-side because they share the same antenna with limited attenuation and, as a result, the receiver’s performance is corrupted. Hence, it is critical to remove the leakage signal from the receiver’s path by designing another block called self-interference cancellation (SIC). The main goal of this dissertation is to develop the SIC block embedded in the current-mode FD receivers. To this end, the regenerated cancellation current signal is fed to the inputs of the base-band filter and after the mixer of a (direct-conversion) current-mode FD receiver. Since the pattern of the transmitter (the digital signal generated by DSP) is known, a high-speed digital-to-Analog converter (DAC) with medium-resolution can perfectly suppress main part of the leakage on the receiver path. A capacitive DAC (CDAC) is chosen among the available solutions because it is compatible with advanced CMOS technology for high-speed application and the medium-resolution designs. Although the main application of the design is to perform the cancellation, it can also be employed as a stand-alone DAC in the Analog (I/Q) transmitter. The SIC circuitry includes a trans-impedance amplifier (TIA), two DACs, high-speed digital circuits, and built-in-self-test section (BIST). According to the available specification for full-duplex communication system, the resolution and working frequency of the CDAC are calculated (designed) equal to 10-bit (3 binary+ 2 binary + 5 thermometric) and 1GHz, respectively. In order to relax the design of the TIA (settling time of the DAC), the CDAC implements using 2-way time-interleaved (TI) manner (the effective SIC frequency equals 2GHz) without using any calibration technique. The CDAC is also developed with the split-capacitor technique to lower the negative effects of the conventional binary-weighted DAC. By adding one extra capacitor on the left-side of the split-capacitor, LSB-side, the value of the split-capacitor can be chosen as an integer value of the unit capacitor. As a result, it largely enhances the linearity of the CADC and cancellation performance. If the block works as a stand-alone DAC with non-TI mode, the digital input code representing a Sinus waveform with an amplitude 1dB less than full-scale and output frequency around 10.74MHz, chosen by coherent sampling rule, then the ENOB, SINAD, SFDR, and output signal are 9.4-bit, 58.2 dB, 68.4dBc, and -9dBV. The simulated value of the |DNL| (static linearity) is also less than 0.7. The similar simulation was done in the SIC mode while the capacitive-array woks in the TI mode and cancellation current is set to the full-scale. Hence, the amount of cancelling the SI signal at the output of the TIA, SNDR, SFDR, SNDRequ. equals 51.3dB, 15.1 dB, 24dBc, 66.4 dB. The designed SIC cannot work as a closed-loop design. The layout was optimally drawn in order to minimize non-linearity, the power-consumption of the decoders, and reduce the complexity of the DAC. By distributing the thermometric cells across the array and using symmetrical switching scheme, the DAC is less subjected to the linear and gradient effect of the oxide. Based on the post-layout simulation results, the deviation of the design after drawing the layout is studied. To compare the results of the schematic and post-layout designs, the exact conditions of simulation above (schematic simulations) are used. When the block works as a stand-alone CDAC, the ENOB, SINAD, SFDR are 8.5-bit, 52.6 dB, 61.3 dBc. The simulated value of the |DNL| (static linearity) is also limited to 1.3. Likewise, the SI signal at the output of the TIA, SNDR, SFDR, SNDRequ. are equal to 44dB, 11.7 dB, 19 dBc, 55.7 dB

Surpassing Fundamental Limits through Time Varying Electromagnetics

Surpassing the fundamental limits that govern all electromagnetic structures, such as reciprocity and the delay-bandwidth-size limit, will have a transformative impact on all applications based on electromagnetic circuits and systems. For instance, violating principles of reciprocity enables non-reciprocal components such as isolators and circulators, which find application in full-duplex wireless radios, radar, biomedical imaging, and quantum computing systems. Overcoming the delay-bandwidth-size limit enables ultra-broadband yet extremely-compact devices whose size is not fundamentally related to the wavelength at the operating frequency. The focus of this dissertation is on using time-variance as a new toolbox to overcome these fundamental limits and re-imagine circuit and system design. Traditional non-reciprocal components are realized using ferrite materials that loose their reciprocity under the application of external magnetic bias. However, the sheer volume, cost and weight of these magnet based non-reciprocal components coupled with their inability to be fabricated in conventional semiconductor processes, have limited their application to bulky and large-scale systems. Other approaches such as active-biased and non-linearity based non-reciprocity are compatible with semiconductor processes, however, they suffer from other poor linearity and noise performance. In this dissertation, using passive transistor switch as the modulating element, we have proposed the concept of spatio-temporal conductivity modulation and have demonstrated a gamut of non-reciprocal devices ranging from gyrators to isolators and circulators. Through novel circuit topologies, for the first time, we have demonstrated on-chip circulators with multi-watt input power handling, operation at high millimeter-wave frequencies, and tailor made circulators for emerging technologies such as simultaneous-transmit-and-receive MRI and quantum computing. Delay-bandwidth-size trade-off is another fundamental electromagnetic limit, that constrains the delay imparted by a medium or a device within a fixed footprint to be inversely proportional to the signal bandwidth. It is this limit that governs the size of any microwave passive devices to be inversely proportional to its operating frequency. As a part of this dissertation, through intelligent clocking of switched capacitor networks we overcame the delay-bandwidth-size limit, thus resulting in infinitesimal, yet broadband microwave devices. Here we proposed a new paradigm in wave propagation where the properties such as the propagation delay and characteristic impedance does not depend on the constituent elements/materials of the medium, but rather heavily rely on the user-defined modulation scheme, thereby opening huge opportunities for realizing highly-reconfigurable passives. Leveraging these concepts, we demonstrated wide range of reciprocal an non-reciprocal devices including ultra-compact delay elements, highly-reconfigurable microwave passives, ultra-wideband circulators with infinitesimal form-factors and dispersion-free chip scale floquet topological insulators. Application of these devices have also been evaluated in real-world systems through our demonstrations of wideband, full-duplex receivers leveraging switched capacitors based true-time-delay interference cancelers and floquet topological insulator based antenna interfaces for full-duplex phased-arrays and ultra-wideband beamformers. Furthermore, to cater the growing RF and microwave needs of future, large-scale quantum computing systems, we demonstrated a low-cryogenic, wideband circulator based on time modulation of superconducting devices. This superconducting circulator is expected to operate alongside the superconducting qubits, inside a dilution refrigerator at 10mK-100mK, thus enabling a tightly integrated quantum system. We also presented the design and implementation of a cryogenic-CMOS clock driver chip that will generate the clocks required by the superconducting circulator. Finally, we also demonstrated the design and implementation of a low-noise, low power consumption, 6GHz - 8GHz cryogenic downconversion receiver at 4K for cryogenic qubit readout

Fully-Integrated Magnetic-Free Nonreciprocal Components by Breaking Lorentz Reciprocity: from Physics to Applications

Reciprocity is a fundamental physical precept that governs wave propagation in a wide variety of physical domains. The various reciprocity theorems state that the response of a system remains unchanged if the excitation source and the measuring point are interchanged within a medium, and are closely related to the concept of time reversal symmetry in physics. Lorentz reciprocity is a fundamental characteristic of linear, time-invariant electronic and photonic structures with symmetric permittivity and permeability tensors. However, breaking reciprocity enables the realization of nonreciprocal components, such as isolators and circulators, which are critical to electronic, optical and acoustic systems, as well as new functionalities and devices based on novel wave propagation modes. Nonreciprocal components have traditionally relied on magnetic materials such as ferrites that lose reciprocity under the application of an external magnetic field through the Faraday Effect. The need for a magnetic bias limits the applicability of such approaches in small-form-factor Complementary Metal–Oxide–Semiconductor (CMOS)-compatible integrated devices. One of the main features of CMOS technology is the availability of high-speed transistor switches which can be turned ON and OFF, modulating the conductance of the medium. In this dissertation, a novel approach to break Lorentz reciprocity is presented based on staggered commutation in Linear Periodically-Time-Varying (LPTV) circuits. We have demonstrated the world’s first CMOS passive magnetic-free nonreciprocal circulator through spatio-temporal conductivity modulation. Since conductivity in semiconductors can be modulated over a wide range (CMOS transistor ON/OFF conductance ratio at Radio Frequency (RF)/millimeter-wave frequencies is as high as 103-105), commutated LPTV networks break reciprocity within a deeply sub-wavelength form-factor with low loss and high linearity. The resulting nonreciprocal components find application in antenna interfaces of wireless communication systems, connecting the Transmitter (TX) and the Receiver (RX) to a shared antenna. This is particularly important for full-duplex wireless, where the TX and the RX operate simultaneously at the same frequency band and need to be highly isolated in order to maintain receiver sensitivity. Multiple fully-integrated full-duplex receivers are demonstrated in this dissertation that best show the synergy between the physical concept and application-based implementations by using circuit techniques to benefit the system-level performance, such as TX-side linearity enhancement and co-design and co-optimization of the antenna interface and the RX and utilization of the multi-phase structure of our antenna interfaces for analog beamforming in multi-antenna systems. Finally, this dissertation discusses some of the fundamental limits of space-time modulated nonreciprocal structures, as well as new directions to build nonreciprocal components which can ideally be infinitesimal in size. A novel family of inductor-less nonreciprocal components including circulators and isolators have been demonstrated that achieve a wide tuning range in an infinitesimal form-factor. This family of devices combine reciprocal and nonreciprocal modes of operation, through the transfer properties of fundamental and harmonics of the system and enable a wide variety of functionalities

SAW-Less Digitally-Assisted Receivers

Today’s wireless devices, like our smartphones, are able to handle multiple standards and bands for different applications, such as Bluetooth, Wi-Fi and data-voice communications. However, the cost of a modern transceiver is becoming mainly dominated by the large number of off-chip passive components, like Duplexers and SAW filters, needed to distinguish the desired signal among many interferences. Addressing the challenges that arise from the lack of RF filtering, a SAW-less architecture represents an interesting solution to reduce the platform complexity. This thesis proposes a feasible solution based on a SAW-less RF front-end able to meet the standard requirements and a digital system tailored to the RF path. The digital architecture, which represents the main topic of this thesis, is described in detail and experimentally tested to validate the proposed solutions