Two-Level Rectilinear Steiner Trees

Given a set $P$ of terminals in the plane and a partition of $P$ into $k$ subsets $P_1, ..., P_k$, a two-level rectilinear Steiner tree consists of a rectilinear Steiner tree $T_i$ connecting the terminals in each set $P_i$ ($i=1,...,k$) and a top-level tree $T_{top}$ connecting the trees $T_1, ..., T_k$. The goal is to minimize the total length of all trees. This problem arises naturally in the design of low-power physical implementations of parity functions on a computer chip. For bounded $k$ we present a polynomial time approximation scheme (PTAS) that is based on Arora's PTAS for rectilinear Steiner trees after lifting each partition into an extra dimension. For the general case we propose an algorithm that predetermines a connection point for each $T_i$ and $T_{top}$ ($i=1,...,k$). Then, we apply any approximation algorithm for minimum rectilinear Steiner trees in the plane to compute each $T_i$ and $T_{top}$ independently. This gives us a $2.37$-factor approximation with a running time of $\mathcal{O}(|P|\log|P|)$ suitable for fast practical computations. The approximation factor reduces to $1.63$ by applying Arora's approximation scheme in the plane

Interconnect optimizations for nanometer VLSI design

textAs the semiconductor technology scales into deeper sub-micron domain, billions of transistors can be used on a single system-on-chip (SOC) makes interconnection optimization more important roughly for two reasons. First, congestion, power, timing in routing and buffering requirements make inter- connection optimization more and more challenging. Second, gate delay get- ting shorter while the RC delay gets longer due to scaling. Study of interconnection construction and optimization algorithms in real industry flows and designs ends up with interesting findings. One used to be overlooked but very important and practical problem is how to utilize over- the-block routing resources intelligently. Routing over large IP blocks needs special attention as there is almost no way to insert buffers inside hard IP blocks, which can lead to unsolvable slew/timing violations. In current design flows we have seen, the routing resources over the IP blocks were either dealt as routing blockages leading to a significant waste, or simply treated in the same way as outside-the-block routing resources, which would violate the slew constraints and thus fail buffering. To handle that, this work proposes a novel buffering-aware over-the- block rectilinear Steiner minimum tree (BOB-RSMT) algorithm which helps reclaim the “wasted” over-the-block routing resources while meeting user-specified slew constraints. Proposed algorithm incrementally and efficiently migrates initial tree structures with buffering-awareness to meet slew constraints while minimizing wire-length. Moreover, due to the fact that timing optimization is important for the VLSI design, in this work, timing-driven over-the-block rectilinear Steiner tree (TOB-RST) is also studied to optimize critical paths. This proposed TOB-RST algorithm can be used in routing or post-routing stage to provide high-quality topologies to help close timing. Then a follow-up problem emerges: how to accomplish the whole routing with over-the-block routing resources used properly. Utilizing over-the- block routing resources could dramatically improve the routing solution, yet require special attention, since the slew, affected by different RC on different metal layers, must be constrained by buffering and is easily violated. Moreover, even of all nets are slew-legalized, the routing solution could still suffer from heavy congestion problem. A new global router, BOB-Router, is to solve the over-the-block global routing problem through minimizing overflows, wire-length and via count simultaneously without violating slew constraints. Based on my completed works, BOB-RSMT and BOB-Router tremendously improve the overall routing and buffering quality. Experimental results show that proposed over-the-block rectilinear Steiner tree construction and routing completely satisfies the slew constraints and significantly outperforms the obstacle-avoiding rectilinear Steiner tree construction and routing in terms of wire-length, via count and overflows.Electrical and Computer Engineerin

Optimal Flood Control

A mathematical model for optimal control of the water levels in a chain of reservoirs is studied. Some remarks regarding sensitivity with respect to the time horizon, terminal cost and forecast of inflow are made

Shortest Paths and Steiner Trees in VLSI Routing

Routing is one of the major steps in very-large-scale integration (VLSI) design. Its task is to find disjoint wire connections between sets of points on a chip, subject to numerous constraints. This problem is solved in a two-stage approach, which consists of so-called global and detailed routing steps. For each set of metal components to be connected, global routing reduces the search space by computing corridors in which detailed routing sequentially determines the desired connections as shortest paths. In this thesis, we present new theoretical results on Steiner trees and shortest paths, the two main mathematical concepts in routing. In the practical part, we give computational results of BonnRoute, a VLSI routing tool developed at the Research Institute for Discrete Mathematics at the University of Bonn. Interconnect signal delays are becoming increasingly important in modern chip designs. Therefore, the length of paths or direct delay measures should be taken into account when constructing rectilinear Steiner trees. We consider the problem of finding a rectilinear Steiner minimum tree (RSMT) that --- as a secondary objective --- minimizes a signal delay related objective. Given a source we derive some structural properties of RSMTs for which the weighted sum of path lengths from the source to the other terminals is minimized. Also, we present an exact algorithm for constructing RSMTs with weighted sum of path lengths as secondary objective, and a heuristic for various secondary objectives. Computational results for industrial designs are presented. We further consider the problem of finding a shortest rectilinear Steiner tree in the plane in the presence of rectilinear obstacles. The Steiner tree is allowed to run over obstacles; however, if it intersects an obstacle, then no connected component of the induced subtree must be longer than a given fixed length. This kind of length restriction is motivated by its application in VLSI routing where a large Steiner tree requires the insertion of repeaters which must not be placed on top of obstacles. We show that there are optimal length-restricted Steiner trees with a special structure. In particular, we prove that a certain graph (called augmented Hanan grid) always contains an optimal solution. Based on this structural result, we give an approximation scheme for the special case that all obstacles are of rectangular shape or are represented by at most a constant number of edges. Turning to the shortest paths problem, we present a new generic framework for Dijkstra's algorithm for finding shortest paths in digraphs with non-negative integral edge lengths. Instead of labeling individual vertices, we label subgraphs which partition the given graph. Much better running times can be achieved if the number of involved subgraphs is small compared to the order of the original graph and the shortest path problems restricted to these subgraphs is computationally easy. As an application we consider the VLSI routing problem, where we need to find millions of shortest paths in partial grid graphs with billions of vertices. Here, the algorithm can be applied twice, once in a coarse abstraction (where the labeled subgraphs are rectangles), and once in a detailed model (where the labeled subgraphs are intervals). Using the result of the first algorithm to speed up the second one via goal-oriented techniques leads to considerably reduced running time. We illustrate this with the routing program BonnRoute on leading-edge industrial chips. Finally, we present computational results of BonnRoute obtained on real-world VLSI chips. BonnRoute fulfills all requirements of modern VLSI routing and has been used by IBM and its customers over many years to produce more than one thousand different chips. To demonstrate the strength of BonnRoute as a state-of-the-art industrial routing tool, we show that it performs excellently on all traditional quality measures such as wire length and number of vias, but also on further criteria of equal importance in the every-day work of the designer

NN-Steiner: A Mixed Neural-algorithmic Approach for the Rectilinear Steiner Minimum Tree Problem

Recent years have witnessed rapid advances in the use of neural networks to solve combinatorial optimization problems. Nevertheless, designing the "right" neural model that can effectively handle a given optimization problem can be challenging, and often there is no theoretical understanding or justification of the resulting neural model. In this paper, we focus on the rectilinear Steiner minimum tree (RSMT) problem, which is of critical importance in IC layout design and as a result has attracted numerous heuristic approaches in the VLSI literature. Our contributions are two-fold. On the methodology front, we propose NN-Steiner, which is a novel mixed neural-algorithmic framework for computing RSMTs that leverages the celebrated PTAS algorithmic framework of Arora to solve this problem (and other geometric optimization problems). Our NN-Steiner replaces key algorithmic components within Arora's PTAS by suitable neural components. In particular, NN-Steiner only needs four neural network (NN) components that are called repeatedly within an algorithmic framework. Crucially, each of the four NN components is only of bounded size independent of input size, and thus easy to train. Furthermore, as the NN component is learning a generic algorithmic step, once learned, the resulting mixed neural-algorithmic framework generalizes to much larger instances not seen in training. Our NN-Steiner, to our best knowledge, is the first neural architecture of bounded size that has capacity to approximately solve RSMT (and variants). On the empirical front, we show how NN-Steiner can be implemented and demonstrate the effectiveness of our resulting approach, especially in terms of generalization, by comparing with state-of-the-art methods (both neural and non-neural based).Comment: This paper is the complete version with appendix of the paper accepted in AAAI'24 with the same titl

Speeding-up Dynamic Programming with Representative Sets - An Experimental Evaluation of Algorithms for Steiner Tree on Tree Decompositions

Dynamic programming on tree decompositions is a frequently used approach to solve otherwise intractable problems on instances of small treewidth. In recent work by Bodlaender et al., it was shown that for many connectivity problems, there exist algorithms that use time, linear in the number of vertices, and single exponential in the width of the tree decomposition that is used. The central idea is that it suffices to compute representative sets, and these can be computed efficiently with help of Gaussian elimination. In this paper, we give an experimental evaluation of this technique for the Steiner Tree problem. A comparison of the classic dynamic programming algorithm and the improved dynamic programming algorithm that employs the table reduction shows that the new approach gives significant improvements on the running time of the algorithm and the size of the tables computed by the dynamic programming algorithm, and thus that the rank based approach from Bodlaender et al. does not only give significant theoretical improvements but also is a viable approach in a practical setting, and showcases the potential of exploiting the idea of representative sets for speeding up dynamic programming algorithms