15 research outputs found

    A Review on Different Techniques of Mutual Coupling Reduction Between Elements of Any MIMO Antenna. Part 1: DGSs and Parasitic Structures

    Get PDF
    This two-part article presents a review of different techniques of mutual coupling (MC) reduction. MC is a major issue when an array of antennas is densely packed. When the separation between the antennas i

    A Review: Circuit Theory of Microstrip Antennas for Dual-, Multi-, and Ultra-Widebands

    Get PDF
    In this chapter, a review has been presented on dual-band, multiband, and ultra-wideband (UWB). This review has been classified according to antenna feeding and loading of antennas using slots and notch and coplanar structure. Thereafter a comparison of dual-band, multiband, and ultra-wideband antenna has been presented. The basic geometry of patch antenna has been present along with its equivalent circuit diagram. It has been observed that patch antenna geometry for ultra-wideband is difficult to achieve with normal structure. Ultra-wideband antennas are achieved with two or more techniques; mostly UWB antennas are achieved from coplaner structures

    Performance investigation of vertical axis wind turbine with savonius rotor using Computational Fluid Dynamics (CFD)

    Get PDF
    The quest of clean and sustainable energy has grown rapidly all over the world in the recent years. Among the renewable energy resources available, wind energy is considered one of the reliable, environmentally friendly, green and fastest-growing source of electricity generation. This generation is accomplished through wind turbines. However, the efficiency of these wind turbines is still very limited and unsatisfactory. The primary goal of this study is to evaluate the performance of a Savonius rotor wind turbine in terms of aerodynamic characteristics, including torque, torque coefficient, and power coefficient. The design of Savonius wind turbine blades is varied and its effects is observed. The simulation models are developed using a modeling software known as Solidworks 2021 and then generated into Ansys Design Modeler 2021 R1 to define the fluid domain. In total, three distinct turbine blades are modelled while varying the diameter and height of the rotor. The simulation study is performed using FLUENT 2021 R21. A constant wind speed value of 9.2 m/s has been used throughout the simulation. The simulation was carried out using a transient time flow with a constant upstream wind speed. The results have shown that the power coefficient of all models increases with TSR and the highest efficiency is consensually obtained at almost a unity (0.9) TSR. Comparing the performance of all models, Model 2 generates the highest power coefficient followed by Model 3 and Model 1, respectively. In terms of power, torque and torque coefficient, nearly similar conclusion is drawn

    Design synthesis and miniaturization of multiband and reconfigurable microstrip antenna for future wireless applications

    Get PDF
    Tese de Doutoramento. Engenharia Electrónica e de Computadores - Telecomunicações. Faculdade de Engenharia. Universidade do Porto. 201

    Microwave and millimeter-wave rectifying circuit arrays and ultra-wideband antennas for wireless power transmission and communications

    Get PDF
    In the future, space solar power transmission and wireless power transmission will play an important role in gathering clean and infinite energy from space. The rectenna, i.e., a rectifying circuit combined with an antenna, is one of the most important components in the wireless power transmission system. To obtain high power and high output voltage, the use of a large rectenna array is necessary. Many novel rectennas and rectenna arrays for microwave and millimeter-wave wireless power transmission have been developed. Unlike the traditional rectifying circuit using a single diode, dual diodes are used to double the DC output voltage with the same circuit layout dimensions. The rectenna components are then combined to form rectenna arrays using different interconnections. The rectennas and the arrays are analyzed by using a linear circuit model. Furthermore, to precisely align the mainbeams of the transmitter and the receiver, a retrodirective array is developed to maintain high efficiency. The retrodirective array is able to track the incident wave and resend the signal to where it came from without any prior known information of the source location. The ultra-wideband radio has become one of the most important communication systems because of demand for high data-rate transmission. Hence, ultra-wideband antennas have received much attention in mobile wireless communications. Planar monopole ultra-wideband antennas for UHF, microwave, and millimeter-wave bands are developed, with many advantages such as simple structure, low cost, light weight, and ease of fabrication. Due to the planar structures, the ultra-wideband antennas can be easily integrated with other circuits. On the other hand, with an ultra-wide bandwidth, source power can be transmitted at different frequencies dependent on power availability. Furthermore, the ultra-wideband antenna can potentially handle wireless power transmission and data communications simultaneously. The technologies developed can also be applied to dual-frequency or the multi-frequency antennas. In this dissertation, many new rectenna arrays, retrodirective rectenna arrays, and ultra-wideband antennas are presented for microwave and millimeter-wave applications. The technologies are not only very useful for wireless power transmission and communication systems, but also they could have many applications in future radar, surveillance, and remote sensing systems

    Passive Microwave Components and Antennas

    Get PDF

    1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

    Get PDF
    A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

    Beam scanning by liquid-crystal biasing in a modified SIW structure

    Get PDF
    A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium

    Switched-beam antenna array design for millimeter-wave applications

    Get PDF
    The limited coverage of wireless communication at the millimeter-wave frequency band due to large free-space path loss, i.e. large signal attenuation, has been a major problem. Furthermore, shadowing and small-scale fading may reduce the received signal even more. An array of rod antennas is designed to tackle those problems by providing high gain, broad scan range, and a shaped beam. Each patch, which couples the electromagnetic wave to the rod, is fed by a coplanar waveguide (CPW) feedline. Each rod antenna demonstrates 18 dBi realized gain and 20° half power beamwidth (HPBW). Moreover, the 4 GHz bandwidth of the antenna provides high data rate for the gigabit wireless application. Furthermore, the Radio Frequency Microelectromechanical System (RF MEMS) switch is used to realize a switched antenna with a broad scan range. The design method and the characterization of the antenna are presented. The proposed antenna system is suitable for a wide range of applications, such as wireless high definition video/audio, USB and firewire replacement, Frequency Modulated Continuous Wave (FMCW) radar, and home/office backhaul application at millimeter-wave frequency
    corecore