Integrated high-voltage switched-capacitor DC-DC converters

The focus of this work is on the integrated circuit (IC) level integration of high-voltage switched-capacitor (SC) converters with the goal of fully integrated power management solutions for system-on-chip (SoC) and system-in-pagage (SiP) applications. The full integration of SC converters provides a low cost and compact power supply solution for modern electronics. Currently, there are almost no fully integrated SC converters with input voltages above 5 V. The purpose of this work is to provide solutions for higher input voltages. The increasing challenges of a compact and efficient power supply on the chip are addressed. High-voltage rated components and the increased losses caused by parasitics not only reduce power density but also efficiency. Loss mechanisms in high-voltage SC converters are investigated resulting in an optimized model for high-voltage SC converters. The model developed allows an appropriate comparison of different semiconductor technologies and converter topologies. Methods and design proposals for loss reduction are presented. Control of power switches with their supporting circuits is a further challenge for high-voltage SC converters. The aim of this work is to develop fully integrated SC converters with a wide input voltage range. Different topologies and concepts are investigated. The implemented fully integrated SC converter has an input voltage range of 2 V to 13 V. This is twice the range of existing converters. This is achieved by an implemented buck and boost mode as well as 17 conversion ratios. Experimental results show a peak efficiency of 81.5%. This is the highest published peak efficiency for fully integrated SC converters with an input voltage > 5V. With the help of the model developed in this work, a three-phase SC converter topology for input voltages up to 60 V is derived and then investigated and discussed. Another focus of this work is on the power supply of sensor nodes and smart home applications with low-power consumption. Highly integrated micro power supplies that operate directly from mains voltage are particularly suitable for these applications. The micro power supply proposed in this work utilizes the high-voltage SC converter developed. The output power is 14 times higher and the power density eleven times higher than prior work. Since plenty of power switches are built into modern multi-ratio SC converters, the switch control circuits must be optimized with regard to low-power consumption and area requirements. In this work, different level shifter concepts are investigated and a low-power high-voltage level shifter for 50 V applications based on a capacitive level shifter is introduced. The level shifter developed exceeds the state of the art by a factor of more than eleven with a power consumption of 2.1pJ per transition. A propagation delay of 1.45 ns is achieved. The presented high-voltage level shifter is the first level shifter for 50 V applications with a propagation delay below 2 ns and power consumption below 20pJ per transition. Compared to the state of the art, the figure of merit is significantly improved by a factor of two. Furthermore, various charge pump concepts are investigated and evaluated within the context of this work. The charge pump, optimized in this work, improves the state of the art by a factor of 1.6 in terms of efficiency. Bidirectional switches must be implemented at certain locations within the power stage to prevent reverse conduction. The topology of a bidirectional switch developed in this work reduces the dynamic switching losses by 70% and the area consumption including the required charge pumps by up to 65% compared to the state of the art. These improvements make it possible to control the power switches in a fast and efficient way. Index terms — integrated power management, high input voltage, multi-ratio SC converter, level shifter, bidirectional switch, micro power supplyDer Schwerpunkt dieser Arbeit liegt auf der Erforschung von Switched-Capacitor (SC) Spannungswandler für höhere Eingangsspannungen. Ziel der Arbeit ist es Lösungen für ein voll auf dem Halbleiterchip integriertes Power Management anzubieten um System on Chip (SoC) und System in Package (SiP) zu ermöglichen. Die vollständige Integration von SC Spannungswandlern bietet eine kostengünstige und kompakte Spannungsversorgungslösung für moderne Elektronik. Der kontinuierliche Trend hin zu immer kompakterer Elektronik und hin zu höheren Versorgungsspannungen wird in dieser Arbeit adressiert. Aktuell gibt es sehr wenige voll integrierte SC Spannungswandler mit einer Eingangsspannung größer 5 V. Die mit steigender Spannung zunehmenden Herausforderungen an eine kompakte und effiziente Spannungsversorgung auf dem Chip werden in dieser Arbeit untersucht. Die höhere Spannungsfestigkeit der verwendeten Komponenten korreliert mit erhöhten Verlusten und erhöhtem Flächenverbrauch, welche sich negativ auf den Wirkungsgrad und die Leistungsdichte von SC Spannungswandlern auswirkt. Bestandteil dieser Arbeit ist die Untersuchung dieser Verlustmechanismen und die Entwicklung eines Modells, welches speziell für höhere Spannungen optimiert wurde. Das vorgestellte Modell ermöglicht zum einen die optimale Dimensionierung der Spannungswandler und zum anderen faire Vergleichsmöglichkeiten zwischen verschiedenen SC Spannungswandler Architekturen und Halbleitertechnologien. Demnach haben sowohl die gewählte Architektur und Halbleitertechnologie als auch die Kombination aus gewählter Architektur und Technologie erheblichen Einfluss auf die Leistungsfähigkeit der Spannungswandler. Ziel dieser Arbeit ist die Vollintegration eines SC Spannungswandlers mit einem weiten und hohen Eingangsspannungsbereich zu entwickeln. Dazu wurden verschiedene Schaltungsarchitekturen und Konzepte untersucht. Der vorgestellte vollintegrierte SC Spannungswandler weist einen Eingangsspannungsbereich von 2 V bis 13 V auf. Dies ist eine Verdopplung im Vergleich zum Stand der Technik. Dies wird durch einen implementierten Auf- und Abwärtswandler-Betriebsmodus sowie 17 Übersetzungsverhältnisse erreicht. Experimentelle Ergebnisse zeigen einen Spitzenwirkungsgrad von 81.5%. Dies ist der höchste veröffentlichte Spitzenwirkungsgrad für vollintegrierte SC Spannungswandler mit einer Eingangsspannung größer 5 V. Mit Hilfe des in dieser Arbeit entwickelten Modells wird eine dreiphasige SC Spannungswandler Architektur für Eingangsspannungen bis zu 60 V entwickelt und anschließend analysiert und diskutiert. Ein weiterer Schwerpunkt dieser Arbeit adressiert die kompakte Spannungsversorgung von Sensorknoten mit geringem Stromverbrauch, für Anwendungen wie Smart Home und Internet der Dinge (IoT). Für diese Anwendungen eignen sich besonders gut hochintegrierte Mikro-Netzteile, welche direkt mit dem 230VRMS-Hausnetz (bzw. 110VRMS) betrieben werden können. Das in dieser Arbeit vorgestellte Mikro-Netzteil nutzt einen in dieser Arbeit entwickelten SC Spannungswandler für hohe Eingangsspannungen. Die damit erzielte Ausgangsleistung ist 14-mal größer im Vergleich zum Stand der Technik. In SC Spannungswandlern für hohe Spannungen werden viele Leistungsschalter benötigt, deshalb muss bei der Schalteransteuerung besonders auf einen geringen Leistungsverbrauch und Flächenbedarf der benötigten Schaltungsblöcke geachtet werden. Gegenstand dieser Arbeit ist sowohl die Analyse verschiedener Konzepte für Pegelumsetzer, als auch die Entwicklung eines stromsparenden Pegelumsetzers für 50 V-Anwendungen. Mit einer Leistungsaufnahme von 2.1pJ pro Signalübergang reduziert der entwickelte Pegelumsetzer mit kapazitiver Kopplung um mehr als elfmal die Leistungsaufnahme im Vergleich zum Stand der Technik. Die erreichte Laufzeitverzögerung beträgt 1.45 ns. Damit erzielt der vorgestellte Hochspannungs-Pegelumsetzer als erster Pegelumsetzer für 50 V-Anwendungen eine Laufzeitverzögerung unter 2 ns und eine Leistungsaufnahme unter 20pJ pro Signalwechsel. Im Vergleich zum Stand der Technik wird die Leistungskennzahl um den Faktor zwei deutlich verbessert. Darüber hinaus werden im Rahmen dieser Arbeiten verschiedene Ladungspumpenkonzepte untersucht und bewertet. Die in dieser Arbeit optimierte Ladungspumpe verbessert den Stand der Technik um den Faktor 1.6 in Bezug auf den Wirkungsgrad. Die in dieser Arbeit entwickelte Schaltungsarchitektur eines bidirektionalen Schalters reduziert die dynamischen Schaltverluste um 70% und den benötigten Flächenbedarf inklusive der benötigten Ladungspumpe um bis zu 65% gegenüber dem Stand der Technik. Diese Verbesserungen ermöglichen es, die Leistungsschalter schnell und effizient anzusteuern. Schlagworte — Integriertes Powermanagement, hohe Eingangsspannung, Multi-Ratio SC Spannungswan- dler, Pegelumsetzer, bidirektionaler Schalter, Mikro-Netztei

Pushing the Boundary of the 48 V Data Center Power Conversion in the AI and IoT Era

openThe increasing interest in cloud-based services, the Internet-of-Things and the take-over of artificial intelligence computing require constant improvement of the power distribution network. Electricity consumption of data centers, which drains a consistent slice of modern world energy production, is projected to increase tremendously during the next decade. Data centers are the backbone of modern economy; as a consequence, energy-aware resource allocation heuristics are constantly researched, leading the major IT services providers to develop new power conversion architectures to increase the overall webfarm distribution efficiency, together reducing the resulting carbon footprint and maximizing their investments. As higher voltage distribution yields lower conduction losses, vendors are moving from the 12 V rack bus to 48 V solutions together with research centers and especially data center developers. As mentioned, efficiency is crucial to address in this scenario and the whole conversion chain, i.e. from the 48 V bus to the CPU/GPU/ASIC voltage, must be optimized to decrease wasted energy inside the server rack. Power density for this converters family is also paramount to consider, as the overall system must occupy as less area and volume as possible. LLC resonant converters are commonly used as IBCs (intermediate bus converters), together with their GaN implementations because of their multiple advantages in efficiency and size, while multiphase-buck-derived topologies are the most common solution to step-down-to and regulate the final processor voltage as they're well-know, easy to scale and design. This dissertation proposes a family of non-isolated, innovative converters capable of increasing the power density and the efficiency of the state-of-the-art 48 V to 1.8/0.9 V conversion. In this work three solutions are proposed, which can be combined or used as stand-alone converters: an ASIC on-chip switched-capacitor resonant voltage divider, two unregulated Google-STC-derived topologies for the IBC stage (48 V to 12 V and 48 V to 4.8 V + 10.6 V dual-output) and a complete 48 V to 1.8 V ultra-dense PoL converter. Each block has been thoroughly tested and researched, therefore mathematical and experimental results are provided for each solution, together with state-of-the-art comparisons and contextualization.The increasing interest in cloud-based services, the Internet-of-Things and the take-over of artificial intelligence computing require constant improvement of the power distribution network. Electricity consumption of data centers, which drains a consistent slice of modern world energy production, is projected to increase tremendously during the next decade. Data centers are the backbone of modern economy; as a consequence, energy-aware resource allocation heuristics are constantly researched, leading the major IT services providers to develop new power conversion architectures to increase the overall webfarm distribution efficiency, together reducing the resulting carbon footprint and maximizing their investments. As higher voltage distribution yields lower conduction losses, vendors are moving from the 12 V rack bus to 48 V solutions together with research centers and especially data center developers. As mentioned, efficiency is crucial to address in this scenario and the whole conversion chain, i.e. from the 48 V bus to the CPU/GPU/ASIC voltage, must be optimized to decrease wasted energy inside the server rack. Power density for this converters family is also paramount to consider, as the overall system must occupy as less area and volume as possible. LLC resonant converters are commonly used as IBCs (intermediate bus converters), together with their GaN implementations because of their multiple advantages in efficiency and size, while multiphase-buck-derived topologies are the most common solution to step-down-to and regulate the final processor voltage as they're well-know, easy to scale and design. This dissertation proposes a family of non-isolated, innovative converters capable of increasing the power density and the efficiency of the state-of-the-art 48 V to 1.8/0.9 V conversion. In this work three solutions are proposed, which can be combined or used as stand-alone converters: an ASIC on-chip switched-capacitor resonant voltage divider, two unregulated Google-STC-derived topologies for the IBC stage (48 V to 12 V and 48 V to 4.8 V + 10.6 V dual-output) and a complete 48 V to 1.8 V ultra-dense PoL converter. Each block has been thoroughly tested and researched, therefore mathematical and experimental results are provided for each solution, together with state-of-the-art comparisons and contextualization.Dottorato di ricerca in Ingegneria industriale e dell'informazioneopenUrsino, Mari

Integrated design of high performance pulsed power converters : application to klystron modulators for the compact linear colider (CLIC)

Ce travail de recherche présente l’étude, conception et validation d’une topologie de convertisseur de puissance pulsé qui compense la chute de tension pour des modulateurs de type klystron de haute performance. Cette topologie est capable de compenser la chute de tension du banc de condensateur principal et, en même temps, de faire fonctionner le modulateur avec une consommation de puissance constante par rapport au réseau électrique. Ces spécifications sont requises par le projet Compact Linear Collider (CLIC) pour les modulateurs klystron de son Drive Beam. Le dimensionnement du système est effectué à partir d’un outil d’optimisation globale développé à partir des modèles analytiques qui décrivent les performances de chaque composant du système. Tous les modèles sont intégrés dans un processus optimal intermédiaire de conception qui utilise des techniques d’optimisation afin de réaliser un dimensionnement optimal du système. Les performances de cette solution optimale intermédiaire sont alors évaluées à l’aide d’un modèle plus fin basé sur des simulations numériques. Une technique d’optimisation utilisant l’approche «space mapping» est alors mise en oeuvre. Si l’écart entre les performances prédites et les performances simulées est important, des facteurs de correction sont appliqués aux modèles analytiques et le processus d’optimisation est relancé. Cette méthode permet d’obtenir une solution optimale validée par le modèle fin en réduisant le nombre de simulations. La topologie finale sélectionnée pour le cahier des charges du modulateur CLIC est validée expérimentalement sur des prototypes à échelle réduite. Les résultats valident la méthodologie de dimensionnement et respectent les spécifications.This research work presents the study, design and validation of a pulsed power converter topology that performs accurate voltage droop compensation for high performance klystron modulators. This topology is capable of compensating the voltage droop of the intermediate capacitor bank and, at the same time, it makes possible a constant power consumption operation of the modulator from the utility grid. These two main specifications are required for the Compact Linear Collider (CLIC) Drive Beam klystron modulators. The dimensioning of the system is performed by developing a global optimization design tool. This tool is first based on developed analytical models describing the performances of each system subcomponent. All these models are integrated into an intermediate design environment that uses nonlinear optimization techniques to calculate an optimal dimensioning of the system. The intermediate optimal solution performances are then evaluated using a more accurate model based on numerical simulation. Therefore, an optimization technique using «space mapping» is implemented. If differences between predicted performances and simulated results are non-negligible, correction factors are applied to the analytical models and the optimization process is launched again. This method makes possible to achieve an optimal solution validated by numerical simulation while reducing the number of numerical simulation steps. The selected final topology for the CLIC klystron modulator is experimentally validated using reduced scale prototypes. Results validate the selected methodology and fulfill the specifications

Study and evaluation of distributed power electronic converters in photovoltaic generation applications

This research project has proposed a new modulation technique called “Local Carrier Pulse Width Modulation” (LC-PWM) for MMCs with different cell voltages, taking into account the measured cell voltages to generate switching sequences with more accurate timing. It also adapts the modulator sampling period to improve the transitions from level to level, an important issue to reduce noise at the internal circulating currents. As a result, the new modulation LC-PWM technique reduces the output distortion in a wider range of voltage situations. Furthermore, it effectively eliminates unnecessary AC components of circulating currents, resulting in lower power losses and higher MMC efficiency.Departamento de Tecnología ElectrónicaDoctorado en Ingeniería Industria

High Power and High Frequency Class-DE Inverters

This thesis investigates the various aspects of the theory. design and construction of a Class-DE type inverter and how these affect the power and frequency limits over which a Class-DE inverter can feasibly be used to produce AC (or RF) power. To this extent. an analysis of Class-DE operation in a half-bridge inverter is performed. A similar approach to Hamill [61 is adopted but a different time reference was used. This allows the concept of a conduction angle to b1: introduced and hence enables a more intuitive understanding of the. equations thereafter. Equations to calculate circuit element values LCR ne1wor'k are developed. The amount above the resonant frequency of the LCR network that the switching frequency must be in order to obtain the correct phase lag of the load current is shown. The effect of a non-linear output capacitance is studied, and equations are modified lo take this effect into account. It was found that a Class-DE topology offers a theoretical power advantage over a Clalls-E topology. However, this power advantage decreases with increasing frequency and is dependent on the output capacitance of the active switching devices. Using currently available MOSFETs, a Class-OE topology has a theoretical power advantage over a Class-E topology up to approximately 10MHz. However, the prac1ical problems of implementing a Class-DE invener lO work into the HF band are formidable. These practical problems and the extent to which they ltml! !he operating frequency and power of a Class-DE type inverter are investigated Guidelines to solving these practical problems are discussed and some novel soluuons are developed that considerably extend the feasible operating frequency and power of a Class-DE inverter. These solutions enabled a brc,adband design of the control circuitry. communication-link and gate-drive to be developed. Using these des[gns, a prototype broadband half-bridge inverter was developed which was capable of switching from 50k.Hz through to 6MHz. When operated in the Class-DE mode, the inverter was found to be capable of delivering a power output of over J kW from SOk.l-lz to 5Mllz with an efficiency of over 91 %. The waveforms obtained from the inverter clearly show Class-OE operation. The results of this thesis prove that a Class-DE series resonant inverter can produce. RF power up to a frequency of 5MHz with a higher combination of power and efficiency than any other present topology. The pracucal problems of even higher operaun& frequencies are discussed and some possible solutions suggested. The mismatched load tolerance of a Class-DE type inverter is briefly investigated. A Class-DE Lype inverter could be used for any applications requiring RF power in the HF band, such as AM or SW rransmirters, induction neating and plasma generators. The information presented in this thesis will be useful 10 designers wishing lo implement such an impeller. In add1non a Class-DE inverter could form the first stage of a highly efficient and high frequency DC-DC converter and the 1nformat1on presented here is directly applicable to such an applicatio

Loss allocation in a distribution system with distributed generation units

In Denmark, a large part of the electricity is produced by wind turbines and combined heat and power plants (CHPs). Most of them are connected to the network through distribution systems. This paper presents a new algorithm for allocation of the losses in a distribution system with distributed generation. The algorithm is based on a reduced impedance matrix of the network and current injections from loads and production units. With the algorithm, the effect of the covariance between production and consumption can be evaluated. To verify the theoretical results, a model of the distribution system in Brønderslev in Northern Jutland, including measurement data, has been studied

State-of-the-art of design and operation of power systems with large amounts of wind power, summary of IEA Wind collaboration

An international forum for exchange of knowledge of power system impacts of wind power has been formed under the IEA Implementing Agreement on Wind Energy. The task “Design and Operation of Power Systems with Large Amounts of Wind Power” is analysing existing case studies from different power systems.There are a multitude of studies made and ongoing related to cost of wind integration. However, the results are not easy to compare. This paper summarises the results from 15 case studies