Radiation safety based on the sky shine effect in reactor

In the reactor operation, neutrons and gamma rays are the most dominant radiation. As protection, lead and concrete shields are built around the reactor. However, the radiation can penetrate the water shielding inside the reactor pool. This incident leads to the occurrence of sky shine where a physical phenomenon of nuclear radiation sources was transmitted panoramic that extends to the environment. The effect of this phenomenon is caused by the fallout radiation into the surrounding area which causes the radiation dose to increase. High doses of exposure cause a person to have stochastic effects or deterministic effects. Therefore, this study was conducted to measure the radiation dose from sky shine effect that scattered around the reactor at different distances and different height above the reactor platform. In this paper, the analysis of the radiation dose of sky shine effect was measured using the experimental metho

An efficient asynchronous spatial division multiplexing router for network-on-chip on the hardware platform

The quasi-delay-insensitive (QDI) based asynchronous network-on-chip (ANoC) has several advantages over clock-based synchronous network-on-chips (NoCs). The asynchronous router uses a virtual channel (VC) as a primary flow-control mechanism however, the spatial division multiplexing (SDM) based mechanism performs better over input traffics over VC. This manuscript uses an asynchronous spatial division multiplexing (ASDM) based router for NoC architecture on a field-programmable gate array (FPGA) platform. The ASDM router is configurable to different bandwidths and VCs. The ASDM router mainly contains input-output (I/O) buffers, a switching allocator, and a crossbar unit. The 4-phase 1-of-4 dual-rail protocol is used to construct the I/O buffers. The performance of the ASDM router is analyzed in terms of lower urinary tract symptoms (LUTs) (chip area), delay, latency, and throughput parameters. The work is implemented using Verilog-HDL with Xilinx ISE 14.7 on artix-7 FPGA. The ASDM router achieves % chip area and obtains 0.8 ns of latency with a throughput of 800 Mfps. The proposed router is compared with existing asynchronous approaches with improved latency and throughput metrics

Design and performance optimization of asynchronous networks-on-chip

As digital systems continue to grow in complexity, the design of conventional synchronous systems is facing unprecedented challenges. The number of transistors on individual chips is already in the multi-billion range, and a greatly increasing number of components are being integrated onto a single chip. As a consequence, modern digital designs are under strong time-to-market pressure, and there is a critical need for composable design approaches for large complex systems. In the past two decades, networks-on-chip (NoC’s) have been a highly active research area. In a NoC-based system, functional blocks are first designed individually and may run at different clock rates. These modules are then connected through a structured network for on-chip global communication. However, due to the rigidity of centrally-clocked NoC’s, there have been bottlenecks of system scalability, energy and performance, which cannot be easily solved with synchronous approaches. As a result, there has been significant recent interest in combing the notion of asynchrony with NoC designs. Since the NoC approach inherently separates the communication infrastructure, and its timing, from computational elements, it is a natural match for an asynchronous paradigm. Asynchronous NoC’s, therefore, enable a modular and extensible system composition for an ‘object-orient’ design style. The thesis aims to significantly advance the state-of-art and viability of asynchronous and globally-asynchronous locally-synchronous (GALS) networks-on-chip, to enable high-performance and low-energy systems. The proposed asynchronous NoC’s are nearly entirely based on standard cells, which eases their integration into industrial design flows. The contributions are instantiated in three different directions. First, practical acceleration techniques are proposed for optimizing the system latency, in order to break through the latency bottleneck in the memory interfaces of many on-chip parallel processors. Novel asynchronous network protocols are proposed, along with concrete NoC designs. A new concept, called ‘monitoring network’, is introduced. Monitoring networks are lightweight shadow networks used for fast-forwarding anticipated traffic information, ahead of the actual packet traffic. The routers are therefore allowed to initiate and perform arbitration and channel allocation in advance. The technique is successfully applied to two topologies which belong to two different categories – a variant mesh-of-trees (MoT) structure and a 2D-mesh topology. Considerable and stable latency improvements are observed across a wide range of traffic patterns, along with moderate throughput gains. Second, for the first time, a high-performance and low-power asynchronous NoC router is compared directly to a leading commercial synchronous counterpart in an advanced industrial technology. The asynchronous router design shows significant performance improvements, as well as area and power savings. The proposed asynchronous router integrates several advanced techniques, including a low-latency circular FIFO for buffer design, and a novel end-to-end credit-based virtual channel (VC) flow control. In addition, a semi-automated design flow is created, which uses portions of a standard synchronous tool flow. Finally, a high-performance multi-resource asynchronous arbiter design is developed. This small but important component can be directly used in existing asynchronous NoC’s for performance optimization. In addition, this standalone design promises use in opening up new NoC directions, as well as for general use in parallel systems. In the proposed arbiter design, the allocation of a resource to a client is divided into several steps. Multiple successive client-resource pairs can be selected rapidly in pipelined sequence, and the completion of the assignments can overlap in parallel. In sum, the thesis provides a set of advanced design solutions for performance optimization of asynchronous and GALS networks-on-chip. These solutions are at different levels, from network protocols, down to router- and component-level optimizations, which can be directly applied to existing basic asynchronous NoC designs to provide a leap in performance improvement

A DVFS Cycle Accurate Simulation Framework with Asynchronous NoC Design for Power-Performance Optimizations

Network-on-Chip (NoC) is a flexible and scalable solution to interconnect multi-cores, with a strong influence on the performance of the whole chip. On-chip network affects also the overall power consumption, thus requiring accurate early-stage estimation and optimization methodologies. In this scenario, the Dynamic Voltage Frequency Scaling (DVFS) technique have been proposed both for CPUs and NoCs. The promise is to be a flexible and scalable way to jointly optimize power-performance, addressing both static and dynamic power sources. Being simulation a de-facto prime solution to explore novel multi-core architectures, a reliable full system analysis requires to integrate in the toolchain accurate timing and power models for the DVFS block and for the resynchronization logic between different Voltage and Frequency Islands (VFIs). In such a way, a more accurate validation of novel optimization methodologies which exploit such actuator is possible, since both architectural and actuator overheads are considered at the same time. This work proposes a complete cycle accurate framework for multi-core design supporting Global Asynchronous Local Synchronous (GALS) NoC design and DVFS actuators for the NoC. Furthermore, static and dynamic frequency assignment is possible with or without the use of the voltage regulator. The proposed framework sits on accurate analytical timing model and SPICE-based power measures, providing accurate estimates of both timing and power overheads of the power control mechanisms

Modeling DVFS and Power-Gating Actuators for Cycle-Accurate NoC-Based Simulators

Networks-on-chip (NoCs) are a widely recognized viable interconnection paradigm to support the multi-core revolution. One of the major design issues of multicore architectures is still the power, which can no longer be considered mainly due to the cores, since the NoC contribution to the overall energy budget is relevant. To face both static and dynamic power while balancing NoC performance, different actuators have been exploited in literature, mainly dynamic voltage frequency scaling (DVFS) and power gating. Typically, simulation-based tools are employed to explore the huge design space by adopting simplified models of the components. As a consequence, the majority of state-of-the-art on NoC power-performance optimization do not accurately consider timing and power overheads of actuators, or (even worse) do not consider them at all, with the risk of overestimating the benefits of the proposed methodologies. This article presents a simulation framework for power-performance analysis of multicore architectures with specific focus on the NoC. It integrates accurate power gating and DVFS models encompassing also their timing and power overheads. The value added of our proposal is manyfold: (i) DVFS and power gating actuators are modeled starting from SPICE-level simulations; (ii) such models have been integrated in the simulation environment; (iii) policy analysis support is plugged into the framework to enable assessment of different policies; (iv) a flexible GALS (globally asynchronous locally synchronous) support is provided, covering both handshake and FIFO re-synchronization schemas. To demonstrate both the flexibility and extensibility of our proposal, two simple policies exploiting the modeled actuators are discussed in the article

A Router Architecture for Connection-Oriented Service Guarantees in the MANGO Clockless Network-on-Chip

Submitted on behalf of EDAA (http://www.edaa.com/)International audienceOn-chip networks for future system-on-chip designs need simple, high performance implementations. In order to promote system-level integrity, guaranteed services (GS) need to be provided. We propose a network-on-chip (NoC) router architecture to support this, and demonstrate with a CMOS standard cell design. Our implementation is based on clockless circuit techniques, and thus inherently supports a modular, GALS-oriented design flow. Our router exploits virtual channels to provide connection-oriented GS, as well as connection-less best-effort (BE) routing. The architecture is highly flexible, in that support for different types of BE routing and GS arbitration can be easily plugged into the router