410 research outputs found

    A Capacitive Humidity Sensor Based on Multi-Wall Carbon Nanotubes (MWCNTs)

    Get PDF
    A new type of capacitive humidity sensor is introduced in this paper. The sensor consists of two plate electrodes coated with MWCNT films and four pieces of isolating medium at the four corners of the sensor. According to capillary condensation, the capacitance signal of the sensor is sensitive to relative humidity (RH), which could be transformed to voltage signal by a capacitance to voltage converter circuit. The sensor is tested using different saturated saline solutions at the ambient temperature of 25 °C, which yielded approximately 11% to 97% RH, respectively. The function of the MWCNT films, the effect of electrode distance, the temperature character and the repeatability of the sensor are discussed in this paper

    Wearable sensors for respiration monitoring: a review

    Get PDF
    This paper provides an overview of flexible and wearable respiration sensors with emphasis on their significance in healthcare applications. The paper classifies these sensors based on their operating frequency distinguishing between high-frequency sensors, which operate above 10 MHz, and low-frequency sensors, which operate below this level. The operating principles of breathing sensors as well as the materials and fabrication techniques employed in their design are addressed. The existing research highlights the need for robust and flexible materials to enable the development of reliable and comfortable sensors. Finally, the paper presents potential research directions and proposes research challenges in the field of flexible and wearable respiration sensors. By identifying emerging trends and gaps in knowledge, this review can encourage further advancements and innovation in the rapidly evolving domain of flexible and wearable sensors.This work was supported by the Spanish Government (MICINN) under Projects TED2021-131209B-I00 and PID2021-124288OB-I00.Peer ReviewedPostprint (published version

    Optical humidity sensor based on tapered fiber with multi-walled carbon nanotubes slurry

    Get PDF
    We demonstrated performance comparison of optical humidity sensor for bare and Multi-walled carbon nanotubes (MWCNTs) slurry coated tapered optical fiber. The starting material for MWCNTs slurry is MWCNTs- acrylonitrile butadiene styrene (ABS) based fused deposition modeling (FDM) 3D printer filament. The ABS was dissolved using acetone to produce MWCNTs-acetone suspension. The MWCNTs-acetone suspension was drop-casted on the tapered fiber to produce MWCNTs slurry by evaporation process at room temperature, which resulted the MWCNTs slurry attach to the tapered fiber. The MWCNTs slurry acts as the cladding for humidity changes measurement. The experimental works showed improvement of sensitivity from 3.811 μW/% of bare tapered fiber to 5.17 μW/% for the coated tapered fiber with MWCNTs slurry when the humidity varied from 45% to 80%

    Carbon-based materials for humidity sensing: a short review

    Get PDF
    Humidity sensors are widespread in many industrial applications, ranging from environmental and meteorological monitoring, soil water content determination in agriculture, air conditioning systems, food quality monitoring, and medical equipment to many other fields. Thus, an accurate and reliable measurement of water content in dierent environments and materials is of paramount importance. Due to their rich surface chemistry and structure designability, carbon materials have become interesting in humidity sensing. In addition, they can be easily miniaturized and applied in flexible electronics. Therefore, this short review aims at providing a survey of recent research dealing with carbonaceous materials used as capacitive and resistive humidity sensors. This work collects some successful examples of devices based on carbon nanotubes, graphene, carbon black, carbon fibers, carbon soot, and more recently, biochar produced from agricultural wastes. The pros and cons of the dierent sensors are also discussed in the present review

    FABRICATION OF MWCNT BASED GAS SENSOR USING SITE-SELECTIVE GROWTH OF NANOTUBES ON GOLD PATTERNED SILICON OXIDE SUBSTRATE

    Get PDF
    Growth confinement techniques for multi walled carbon nanotubes on Au/SiO2 surfaces was studied and incorporated into a gas sensor design. A device framework was conceived and a sensor was built to achieve this structure. The fabrication results were analyzed using scanning electron microscopy which confirmed the achievement of highly site-selective growth of carbon nanotubes, exclusively between the interdigitated electrodes. The sensor was then evaluated for its capacitance and conductance response when exposed to NO2 gas. Variation in sensitivities with frequency and flow rate were analyzed. A mathematical model was derived for such a device structure and the predictions of the model were compared with experimental results

    Humidity Sensitivity of Multi-Walled Carbon Nanotube Networks Deposited by Dielectrophoresis

    Get PDF
    This paper presents an investigation on the humidity sensitivity of deposited multi-walled carbon nanotube (MWCNT) networks using ac dielectrophoresis (DEP) between interdigitated electrodes (IDEs). MWCNTs dispersed in ethanol were trapped and enriched between IDEs on a Si/SiO2 substrate under a positive DEP force. After the DEP process, the ethanol was evaporated and the MWCNT network on a substrate with IDEs was put into a furnace for repeated thermal annealing. It was found that the resistance stability of the network was effectively improved through thermal annealing. The humidity sensitivity was obtained by measuring the resistance of the MWCNT network with different relative humidity at room temperature. The experimental results show the resistance increases linearly with increasing the relative humidity from 25% to 95% RH with a sensitivity of 0.5%/%RH. The MWCNT networks have a reversible humidity sensing capacity with response time and recovery time of about 3 s and 25 s, respectively. The resistance is dependent on temperature with a negative coefficient of about −0.33%/K in a temperature range from 293 K to 393 K

    Novel nanocomposite technologies for dynamic monitoring of structures: a comparison between cement-based embeddable and soft elastomeric surface sensors

    Get PDF
    The authors have recently developed two novel solutions for strain sensing using nanocomposite materials. While they both aim at providing cost-effective solutions for the monitoring of local information on large-scale structures, the technologies are different in their applications and physical principles. One sensor is made of a cementitious material, which could make it suitable for embedding within the core of concrete structures prior to casting, and is a resistor, consisting of a carbon nanotube cement-based transducer. The other sensor can be used to create an external sensing skin and is a capacitor, consisting of a flexible conducting elastomer fabricated from a nanocomposite mix, and deployable in a network setup to cover large structural surfaces. In this paper, we advance the understanding of nanocomposite sensing technologies by investigating the potential of both novel sensors for the dynamic monitoring of civil structures. First, an in-depth dynamic characterization of the sensors using a uniaxial test machine is conducted. Second, their performance at dynamic monitoring of a full-scale concrete beam is assessed, and compared against off-the-shelf accelerometers. Experimental results show that both novel technologies compare well against mature sensors at vibration-based structural health monitoring, showing the promise of nanocomposite technologies for the monitoring of large-scale structural systems

    Electrical Response Using Nanotubes on a Fibrous Substrate

    Get PDF
    A device produces an electrical signal in response to a stimulus. The device is formed of a flexible substrate including a layer of fibers, for example, paper, and a solution of dispersed carbon nanotubes coated onto and within the fibers, the solution evaporated to leave carbon nanotubes intertwined within the layer of fibers. The carbon nanotubes are functionalized to be optimized for producing an electrical signal for a particular stimulus, where the stimulus includes exposure of the device to a particular gas or vapor. A number of such devices, some or all of which can be different, are housed together, for producing a complex electronic signal, or for sensing any of a wide variety of stimulus

    Highly reproducible, hysteresis-free, flexible strain sensors by inkjet printing of carbon nanotubes

    No full text
    In order to build upon the exceptional interest for flexible sensors based on carbon nanotube networks (CNNs), the field requires high device-to-device reproducibility. Inkjet printing has provided outstanding results for flexible ohmic sensors in terms of reproducibility of their resistance. However, the reproducibility of the sensitivity, the most critical parameter for sensing application, has been only marginally assessed. In the present paper, CNN based resistive strain sensors fabricated by inkjet-printing on flexible Ethylene Tetrafluoroethylene (EFTE) sheets are presented. The variability on the device initial resistance is studied for 5 different batches of sensors from 3 to 72 devices each. The variability ranges between 8.4% and 43% depending on the size of the batches, with a 20% average. An 8-device batch with 15% variability on initial resistance is further studied for variability on the strain and thermal sensitivity. Standard deviation values are found to be as low as 16% on the strain sensitivity and 8% on the temperature sensitivity. Moreover, the devices are hysteresis free, a rare achievement for CNT strain sensors on plastics
    corecore