Towards Very Large Scale Analog (VLSA): Synthesizable Frequency Generation Circuits.

Driven by advancement in integrated circuit design and fabrication technologies, electronic systems have become ubiquitous. This has been enabled powerful digital design tools that continue to shrink the design cost, time-to-market, and the size of digital circuits. Similarly, the manufacturing cost has been constantly declining for the last four decades due to CMOS scaling. However, analog systems have struggled to keep up with the unprecedented scaling of digital circuits. Even today, the majority of the analog circuit blocks are custom designed, do not scale well, and require long design cycles. This thesis analyzes the factors responsible for the slow scaling of analog blocks, and presents a new design methodology that bridges the gap between traditional custom analog design and the modern digital design. The proposed methodology is utilized in implementation of the frequency generation circuits – traditionally considered analog systems. Prototypes covering two different applications were implemented. The first synthesized all-digital phase-locked loop was designed for 400-460 MHz MedRadio applications and was fabricated in a 65 nm CMOS process. The second prototype is an ultra-low power, near-threshold 187-500 kHz clock generator for energy harvesting/autonomous applications. Finally, a digitally-controlled oscillator frequency resolution enhancement technique is presented which allows reduction of quantization noise in ADPLLs without introducing spurs.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/109027/1/mufaisal_1.pd

DLWUC: Distance and Load Weight Updated Clustering-Based Clock Distribution for SOC Architecture

High-clock skew variations and degradation of driving ability of buffers lead to an additional power dissipation in Clock Distribution Network (CDN) that increases the dimensionality of buffers and coordination among flip-flops. The manual threshold level to predict the Region of Interest (ROI) is not applicable in clustering process due to the complexities of excessive wire length and critical delay. This paper proposes the Distance and Load Weight Updated Clustering (DLWUC) to determine the suitable position of logical components. Initially, the DLWUC utilizes the Hybrid Weighted Distance (HWD) to estimate the distance and construct the distance matrix. The weight value extracted from the sorted distance matrix facilitates the projection of buffers. The updated weight value serves as the base for clustering with labeled outputs. The placement of buffer at the suitable place from load weight updated clustering provides the necessary trade-off between clock provision and load balance. The DLWUC discussed in this paper reduces the size of buffers, skew, power and latency compared to the existing topologies

Générateur distribué d'horloge pour puces globalement et localement synchrones de grande taille

This thesis addresses the problem of global synchronization of large system on chip (SoC). It focuses on the study of an alternative clock generation technique to conventional clock distribution and asynchronous communication. It allows implementation of highly reliable synchronous circuit. My PhD project aims to study and implement a large network (10x10) of all digital phase-locked loop (ADPLL), containing 100 nodes generating a clock for each local digital circuitry. The prototype was implemented on silicon generating clocks in the range 903-1161 MHz. It highlights a maximum phase error of less than 40 ps between two clocks in any neighboring zones. Another important result is the analysis of phase error between two non-neighboring oscillators in distance. By studying an FPGA prototype of the network, we obtained that maximum phase error at steady state between any clock signal and the reference signal is less than three steps of the PFD quantification steps. In order to validate the performance of synchronization in ASIC, we designed an on-chip clocking error measurement circuit. This circuit has a low rate for the off-chip readout (several MHz), and a high resolution (+-2.5 ps). Reconfigurability is another attractive feature. We have explored this feature and proposed a novel topology with different configurations for nodes on the border and in the kernel of the network. This topology has an advantage in prohibiting phase error propagation and reflection.Cette thèse aborde le problème de la synchronisation globale de grand système sur puce (SoC). Il est centré sur l'étude d'une technique de remplacement de la distribution d'horloge classique et d'une communication asynchrone. Il permet la mise en œuvre de circuit synchrone très fiable. Mon projet de thèse vise à étudier et mettre en œuvre un vaste réseau (10x10) de boucle à verrouillage de phase tous numérique (ADPLL), contenant 100 nœuds générant une horloge pour chaque circuit numérique local. Le prototype a été réalisé sur les horloges de génération de silicium dans la gamme de 903-1161 MHz. Elle met en évidence une erreur de phase maximale de moins de 40 ps entre deux horloges dans toutes les zones voisines. Un autre résultat important est l'analyse de l'erreur de phase entre les deux oscillateurs non-voisins dans la distance. En étudiant un prototype FPGA du réseau, on a obtenu que l'erreur de phase maximale à l'état d'équilibre entre un signal d'horloge et le signal de référence est inférieur à trois étapes des étapes de quantification PFD. Afin de valider les performances de la synchronisation dans ASIC, nous avons conçu un circuit d'une erreur de mesure sur la puce d'horloge. Ce circuit a un taux faible de la lecture hors puce (quelques MHz), et une résolution élevée (+ -2,5 ps). Reconfiguration constitue une autre caractéristique intéressante. Nous avons exploré cette fonction et a proposé une nouvelle topologie avec des configurations différentes pour les nœuds sur la frontière et dans le noyau du réseau. Cette topologie présente un avantage en interdisant la propagation des erreurs de phase et de réflexion

Analysis and Design of Energy Efficient Frequency Synthesizers for Wireless Integrated Systems

Advances in ultra-low power (ULP) circuit technologies are expanding the IoT applications in our daily life. However, wireless connectivity, small form factor and long lifetime are still the key constraints for many envisioned wearable, implantable and maintenance-free monitoring systems to be practically deployed at a large scale. The frequency synthesizer is one of the most power hungry and complicated blocks that not only constraints RF performance but also offers subtle scalability with power as well. Furthermore, the only indispensable off-chip component, the crystal oscillator, is also associated with the frequency synthesizer as a reference. This thesis addresses the above issues by analyzing how phase noise of the LO affect the frequency modulated wireless system in different aspects and how different noise sources in the PLL affect the performance. Several chip prototypes have been demonstrated including: 1) An ULP FSK transmitter with SAR assisted FLL; 2) A ring oscillator based all-digital BLE transmitter utilizing a quarter RF frequency LO and 4X frequency multiplier; and 3) An XO-less BLE transmitter with an RF reference recovery receiver. The first 2 designs deal with noise sources in the PLL loop for ultimate power and cost reduction, while the third design deals with the reference noise outside the PLL and explores a way to replace the XO in ULP wireless edge nodes. And at last, a comprehensive PN theory is proposed as the design guideline.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/153420/1/chenxing_1.pd

Frequency Synthesis in Wireless and Wireline Systems

First, a frequency synthesizer for IEEE 802.15.4 / ZigBee transceiver applications that employs dynamic True Single Phase Clocking (TSPC) circuits in its frequency dividers is presented and through the analysis and measurement results of this synthesizer, the need for low power circuit techniques in frequency dividers is discussed. Next, Differential Cascode Voltage-Switch-Logic (DCVSL) based delay cells are explored for implementing radio-frequency (RF) frequency dividers of low power frequency synthesizers. DCVSL ip- ops offer small input and clock capacitance which makes the power consumption of these circuits and their driving stages, very low. We perform a delay analysis of DCVSL circuits and propose a closed-form delay model that predicts the speed of DCVSL circuits with 8 percent worst case accuracy. The proposed delay model also demonstrates that DCVSL circuits suffer from a large low-to-high propagation delay ( PLH) which limits their speed and results in asymmetrical output waveforms. Our proposed enhanced DCVSL, which we call DCVSL-R, solves this delay bottleneck, reducing PLH and achieving faster operation. We implement two ring-oscillator-based voltage controlled oscillators (VCOs) in 0.13 mu m technology with DCVSL and DCVSL-R delay cells. In measurements, for the same oscillation frequency (2.4GHz) and same phase noise (-113dBc/Hz at 10MHz), DCVSL-R VCO consumes 30 percent less power than the DCVSL VCO. We also use the proposed DCVSL-R circuit to implement the 2.4GHz dual-modulus prescaler of a low power frequency synthesizer in 0.18 mu m technology. In measurements, the synthesizer exhibits -135dBc/Hz phase noise at 10MHz offset and 58 mu m settling time with 8.3mW power consumption, only 1.07mWof which is consumed by the dual modulus prescaler and the buffer that drives it. When compared to other dual modulus prescalers with similar division ratios and operating frequencies in literature, DCVSL-R dual modulus prescaler demonstrates the lowest power consumption. An all digital phase locked loop (ADPLL) that operates for a wide range of frequencies to serve as a multi-protocol compatible PLL for microprocessor and serial link applications, is presented. The proposed ADPLL is truly digital and is implemented in a standard complementary metal-oxide-semiconductor (CMOS) technology without any analog/RF or non-scalable components. It addresses the challenges that come along with continuous wide range of operation such as stability and phase frequency detection for a large frequency error range. A proposed multi-bit bidirectional smart shifter serves as the digitally controlled oscillator (DCO) control and tunes the DCO frequency by turning on/off inverter units in a large row/column matrix that constitute the ring oscillator. The smart shifter block is completely digital, consisting of standard cell logic gates, and is capable of tracking the row/column unit availability of the DCO and shifting multiple bits per single update cycle. This enables fast frequency acquisition times without necessitating dual loop fi lter or gear shifting mechanisms. The proposed ADPLL loop architecture does not employ costly, cumbersome DACs or binary to thermometer converters and minimizes loop filter and DCO control complexity. The wide range ADPLL is implemented in 90nm digital CMOS technology and has a 9-bit TDC, the output of which is processed by a 10-bit digital loop filter and a 5-bit smart shifter. In measurements, the synthesizer achieves 2.5GHz-7.3GHz operation while consuming 10mW/GHz power, with an active area of 0.23 mm2

Formal Verification and In-Situ Test of Analog and Mixed-Signal Circuits

As CMOS technologies continuously scale down, designing robust analog and mixed-signal (AMS) circuits becomes increasingly difficult. Consequently, there are pressing needs for AMS design checking techniques, more specifically design verification and design for testability (DfT). The purpose of verification is to ensure that the performance of an AMS design meets its specification under process, voltage and temperature (PVT) variations and different working conditions, while DfT techniques aim at embedding testability into the design, by adding auxiliary circuitries for testing purpose. This dissertation focuses on improving the robustness of AMS designs in highly scaled technologies, by developing novel formal verification and in-situ test techniques. Compared with conventional AMS verification that relies more on heuristically chosen simulations, formal verification provides a mathematically rigorous way of checking the target design property. A formal verification framework is proposed that incorporates nonlinear SMT solving techniques and simulation exploration to efficiently verify the dynamic properties of AMS designs. A powerful Bayesian inference based technique is applied to dynamically tradeoff between the costs of simulation and nonlinear SMT. The feasibility and efficacy of the proposed methodology are demonstrated on the verification of lock time specification of a charge-pump PLL. The powerful and low-cost digital processing capabilities of today?s CMOS technologies are enabling many new in-situ test schemes in a mixed-signal environment. First, a novel two-level structure of GRO-PVDL is proposed for on-chip jitter testing of high-speed high-resolution applications with a gated ring oscillator (GRO) at the first level to provide a coarse measurement and a Vernier-style structure at the second level to further measure the residue from the first level with a fine resolution. With the feature of quantization noise shaping, an effective resolution of 0.8ps can be achieved using a 90nm CMOS technology. Second, the reconfigurability of recent all-digital PLL designs is exploited to provide in-situ output jitter test and diagnosis abilities under multiple parametric variations of key analog building blocks. As an extension, an in-situ test scheme is proposed to provide online testing for all-digital PLL based polar transmitters

A LPDDR4 MEMORY CONTROLLER DESIGN WITH EYE CENTER DETECTION ALGORITHM

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 2. 김수환.The demand for higher bandwidth with reduced power consumption in mobile memory is increasing. In this thesis, architecture of the LPDDR4 memory controller, operated with a LPDDR4 memory, is proposed and designed, and efficient training algorithm, which is appropriate for this architecture, is proposed for memory training and verification. The operation speed range of the LPDDR4 memory specification is from 533Mbps to 4266Mbps, and the LPDDR4 memory controller is designed to support that range of the LPDDR4 memory. The phase-locked loop in the LPDDR4 memory controller is designed to operate between 1333MHz and 2133MHz. To cover the range of the LPDDR4 memory, the selectable frequency divider is used to provide operation clock. The output frequency of the phase-locked loop with divider is from 266MHz to 2133MHz. The delay-locked loop in the LPDDR4 memory controller is designed to operate between 266MHz and 2133MHz with 180˚ phase locking. The delay-locked loop is used each training operation, which is command training, data read and write training. To complete training in each training stage, eye center detection algorithm is used. The circuits for the proposed eye center detection algorithm such as delay line, phase interpolator and reference generator are designed and validated. The proposed 1x2y3x eye center detection algorithm is 23 times faster than conventional two-dimensional eye center detection algorithm and it can be implemented simply. Using 65nm CMOS process, the proposed LPDDR4 memory controller occupies 12mm2. The verification of the LPDDR4 memory controller is performed with commodity LPDDR4 memory. The verification of all training sequence, which is power on, initializing, boot up, command training, write leveling, read training, write training, is performed in this environment. The low voltage swing terminated logic driver and other several functions, including write leveling and data transmission, are verified at 4266Mbps and the entire LPDDR4 memory controller operations from 566Mbps to 1600Mbps are verified. The proposed eye center detection algorithm is verified from 566Mbps to 2843Mbps.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 INTRODUCTION 5 1.3 THESIS ORGANIZATION 7 CHAPTER 2 LPDDR4 MEMORY CONTROLLER DESIGN 8 2.1 DIFFERENCE BETWEEN LPDDR3 AND LPDDR4 MEMORY 8 2.1.1 ARCHITECTURAL DIFFERENCE BETWEEN LPDDR3 AND LPDDR4 MEMORY 10 2.1.2 SOURCE SYNCHRONOUS MATCHED SCHEME AND UNMATCHED SCHEME 11 2.1.3 LOW VOLTAGE SWING TERMINATED LOGIC DRIVER AND TERMINATION SCHEME 12 2.2 LPDDR4 MEMORY CONTROLLER SPECIFICATION 15 2.3 DESIGN PROCEDURE 18 CHAPTER 3 LPDDR4 MEMORY CONTROLLER ARCHITECTURE BASED ON MEMORY TRAINING 20 3.1 LPDDR4 MEMORY TRAINING SEQUENCE 20 3.2 LPDDR4 MEMORY TRAINING EYE DETECTION ALGORITHM 24 3.2.1 EYE CENTER DETECTION 24 3.2.2 1X2Y3X EYE CENTER DETECTION ALGORITHM 27 3.3. LPDDR4 MEMORY CONTROLLER DESIGN BASED ON MEMORY TRAINING 31 3.3.1 ARCHITECTURE FOR MEMORY BOOT UP AND POWER UP 31 3.3.2 CLOCK PATH ARCHITECTURE AND CLOCK TREE 34 3.3.3 COMMAND TRAINING AND COMMAND PATH ARCHITECTURE 35 3.3.4 WRITE LEVELING AND DATA STROBE TRANSMISSION PATH ARCHITECTURE 39 3.3.5 READ TRAINING AND READ PATH ARCHITECTURE 41 3.3.6 WRITE TRAINING AND WRITE PATH ARCHITECTURE 43 3.3.7 NORMAL READ/WRITE OPERATION AND MARGIN TEST 46 CHAPTER 4 LPDDR4 MEMORY CONTROLLER ARCHITECTURE MODELING AND CIRCUIT DESIGN 48 4.1 OVERALL LPDDR4 MEMORY CONTROLLER ARCHITECTURE MODELING 48 4.2 SIMULATION RESULT OF LPDDR4 MEMORY CONTROLLER MODELING 51 4.3 LPDDR4 MEMORY CONTROLLER CIRCUIT DESIGN 61 4.3.1 PHASE-LOCKED LOOP 61 4.3.2 DELAY-LOCKED LOOP 65 4.3.3 TRANSMITTER OF LPDDR4 MEMORY CONTROLLER: WRITE PATH 70 4.3.4 DE-SERIALIZER WITH CLOCK DOMAIN CROSSING 75 CHAPTER 5 MEASUREMENT RESULT OF LPDDR4 MEMORY CONTROLLER 77 5.1 LPDDR4 MEMORY CONTROLLER MEASUREMENT SETUP 77 5.1.1 LPDDR4 MEMORY CONTROLLER FLOOR PLAN AND LAYOUT 77 5.1.2 PACKAGE AND TEST BOARD 79 5.2 LPDDR4 MEMORY CONTROLLER SUB-BLOCK MEASUREMENT 81 5.2.1 PHASE-LOCKED LOOP 81 5.2.2 DELAY-LOCKED LOOP 83 5.2.3 200PS AND 800PS DELAY LINE 85 5.2.4 VOLTAGE REFERENCE GENERATOR 86 5.2.5 PHASE INTERPOLATOR 87 5.3 LPDDR4 MEMORY SYSTEM OPERATION MEASUREMENT 90 CHAPTER 6 CONCLUSION 93 APPENDIX OPERATION FLOW CHART OF THE PROPOSED LPDDR4 MEMORY CONTROLLER 95 BIBLIOGRAPHY 118 KOREAN ABSTRACT 124Docto

Radiation Tolerant Electronics, Volume II

Research on radiation tolerant electronics has increased rapidly over the last few years, resulting in many interesting approaches to model radiation effects and design radiation hardened integrated circuits and embedded systems. This research is strongly driven by the growing need for radiation hardened electronics for space applications, high-energy physics experiments such as those on the large hadron collider at CERN, and many terrestrial nuclear applications, including nuclear energy and safety management. With the progressive scaling of integrated circuit technologies and the growing complexity of electronic systems, their ionizing radiation susceptibility has raised many exciting challenges, which are expected to drive research in the coming decade.After the success of the first Special Issue on Radiation Tolerant Electronics, the current Special Issue features thirteen articles highlighting recent breakthroughs in radiation tolerant integrated circuit design, fault tolerance in FPGAs, radiation effects in semiconductor materials and advanced IC technologies and modelling of radiation effects