446 research outputs found

    A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS

    Get PDF
    © 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio

    Towards a Universal Multi-Standard RF Receiver

    Get PDF
    Future wireless communication market calls for the need of an extreme compact wireless device that can easily access to all the available services at any time and at any location with minimum power consumption and cost. The key is to find a multi-standard wireless receiver that can cover all the service specifications while keeping redundant components to minimum. Reconfigurable concept is right fit the need. In this thesis, a fully integrated universal multi-standard receiver using low-cost CMOS technology has been proposed based on the survey for different wireless receiver specifications and optimum architectures. Tunable receiver building blocks such as filters, LNAs, Mixers, VCOs, gain blocks are the main factor to approach this novel receiver. In order to realize frequency agility, low cost as well as low power consumption, a good switch is a must. In this thesis, MEMS switches are preferred rather than active switches or active tuning elements based on their performance comparisons. In the feasibility study, as an example, first, a reconfigurable LNA and a reconfigurable oscillator using hard wires as switches have been developed, and then a LNA and an oscillator have been designed using a MEMS switch. The effect of hard-wire connection and MEMS to the circuits has been evaluated. No performance degradation has been found when using hard-wire connections, while some has been observed when using MEMS. However, MEMS could be integrated with other circuits on the same die if it could be built on low resistive silicon substrate without performance degradation

    Design and characterization of downconversion mixers and the on-chip calibration techniques for monolithic direct conversion radio receivers

    Get PDF
    This thesis consists of eight publications and an overview of the research topic, which is also a summary of the work. The research described in this thesis is focused on the design of downconversion mixers and direct conversion radio receivers for UTRA/FDD WCDMA and GSM standards. The main interest of the work is in the 1-3 GHz frequency range and in the Silicon and Silicon-Germanium BiCMOS technologies. The RF front-end, and especially the mixer, limits the performance of direct conversion architecture. The most stringent problems are involved in the second-order distortion in mixers to which special attention has been given. The work introduces calibration techniques to overcome these problems. Some design considerations for front-end radio receivers are also given through a mixer-centric approach. The work summarizes the design of several downconversion mixers. Three of the implemented mixers are integrated as the downconversion stages of larger direct conversion receiver chips. One is realized together with the LNA as an RF front-end. Also, some stand-alone structures have been characterized. Two of the mixers that are integrated together with whole analog receivers include calibration structures to improve the second-order intermodulation rejection. A theoretical mismatch analysis of the second-order distortion in the mixers is also presented in this thesis. It gives a comprehensive illustration of the second-order distortion in mixers. It also gives the relationships between the dc-offsets and high IIP2. In addition, circuit and layout techniques to improve the LO-to-RF isolation are discussed. The presented work provides insight into how the mixer immunity against the second-order distortion can be improved. The implemented calibration structures show promising performance. On the basis of these results, several methods of detecting the distortion on-chip and the possibilities of integrating the automatic on-chip calibration procedures to produce a repeatable and well-predictable receiver IIP2 are presented.reviewe

    Flexible CMOS low-noise amplifiers for beyond-3G wireless hand-held devices

    Get PDF
    This paper explores the use of reconfigurable Low-Noise Amplifiers (LNAs) for the implementation of CMOS Radio Frequency (RF) front-ends in the next generation of multi-standard wireless transceivers. Main circuit strategies reported so far for multi-standard LNAs are reviewed and a novel flexible LNA intended for Beyond-3G RF hand-held terminals is presented. The proposed LNA circuit consists of a two-stage topology that combines inductive-source degeneration with PMOS-varactor based tuning network and a programmable load to adapt its performance to different standard specifications without penalizing the circuit noise and with a reduced number of inductors as compared to previous reported reconfigurable LNAs. The circuit has been designed in a 90-nm CMOS technology to cope with the requirements of the GSM, WCDMA, Bluetooth and WLAN (IEEE 802.11b-g) standards. Simulation results, including technology and packaging parasitics, demonstrate correct operation of the circuit for all the standards under study, featuring NF13.3dB and IIP3>10.9dBm, over a 1.85GHz-2.4GHz band, with an adaptive power consumption between 17mW and 22mW from a 1-V supply voltage. Preliminary experimental measurements are included, showing a correct reconfiguration operation within the operation band

    High Performance LNAs and Mixers for Direct Conversion Receivers in BiCMOS and CMOS Technologies

    Get PDF
    The trend in cellular chipset design today is to incorporate support for a larger number of frequency bands for each new chipset generation. If the chipset also supports receiver diversity two low noise amplifiers (LNAs) are required for each frequency band. This is however associated with an increase of off-chip components, i.e. matching components for the LNA inputs, as well as complex routing of the RF input signals. If balanced LNAs are implemented the routing complexity is further increased. The first presented work in this thesis is a novel multiband low noise single ended LNA and mixer architecture. The mixer has a novel feedback loop suppressing both second order distortion as well as DC-offset. The performance, verified by Monte Carlo simulations, is sufficient for a WCDMA application. The second presented work is a single ended multiband LNA with programmable integrated matching. The LNA is connected to an on-chip tunable balun generating differential RF signals for a differential mixer. The combination of the narrow band input matching and narrow band balun of the presented LNA is beneficial for suppressing third harmonic downconversion of a WLAN interferer. The single ended architecture has great advantages regarding PCB routing of the RF input signals but is on the other hand more sensitive to common mode interferers, e.g. ground, supply and substrate noise. An analysis of direct conversion receiver requirements is presented together with an overview of different LNA and mixer architectures in both BiCMOS and CMOS technology

    A New Application of Current Conveyors: The Design of Wideband Controllable Low-Noise Amplifiers

    Get PDF
    The aim of this paper is three-fold. First, it reviews the low-noise amplifier and its relevance in wireless communications receivers. Then it presents an exhaustive review of the existing topologies. Finally, it introduces a new class of LNAs, based on current conveyors, describing the founding principle and the performances of a new single-ended LNA. The new LNAs offer the following notable advantages: total absence of passive elements (and the smallest LNAs in their respective classes); wideband performance, with stable frequency responses from 0 to 3 GHz; easy gain control over wide ranges (0 to 20 dB). Comparisons with other topologies prove that the new class of LNA greatly advances the state of the art

    Design of an adaptive LNA for hand-held devices in a 1-V 90-nm standard RF CMOS technology: From circuit analysis to layout

    Get PDF
    [EN]: This paper deals the design of a reconfigurable Low-Noise Amplifier (LNA) for the next generation of wireless hand-held devices by using a lumped circuit approach based on physical laws. The purpose is not only to present simulation results showing the fulfillment of different standard specifications, but also to demonstrate that each design step has a physical meaning such that the mathematical design flow is simple as well as suitable for hand-work in both laboratory and classroom. The circuit under analysis, which is designed according to technological design rules of a 90nm CMOS technology, is a two-stage topology including inductive-source degeneration, MOS-varactor based tuning networks, and programmable bias currents. This proposal, with reduced number of inductors and minimum power dissipation, adapts its performance to different standard specifications; the LNA is designed to cope with the requirements of GSM (PCS1900), WCDMA, Bluetooth and WLAN (IEEE 802.11b-g). In order to evaluate the effect of technology parasitics on the LNA performance, simulation results demonstrate that the LNA features NF16dB, S11-3.3 dBm over the 1.85-2.48 GHz band. For all the standards under study the adaptive power consumption varies from 25.3 mW to 53.3mW at a power supply of 1-V. The layout of the reconfigurable LNA occupies an area of 1.8mm2.[ES]: Este trabajo presenta el diseño de un amplificador de bajo ruido, LNA (del inglés Low‐Noise Amplifier) reconfigurable para la siguiente generación de dispositivos portátiles de comunicación inalámbricos, usando la aproximación de circuitos concentrados sustentada en leyes físicas. El propósito de este trabajo no es sólo presentar resultados de simulación que muestran el cumplimiento de especificaciones para cada estándar, sino también demostrar que cada paso de diseño tiene un significado físico haciendo que el procedimiento matemático de diseño sea simple y adecuado para el trabajo a mano tanto para actividades en laboratorio como en el aula. El circuito bajo análisis, diseñado en una tecnología CMOS 90nm, consta de dos etapas que incluyen degeneración inductiva de fuente, redes de entonado basadas en varactores MOS, y corrientes de polarización programables. Esta propuesta, con reducido número de inductores y mínima disipación de potencia, adapta su desempeño a las diversas especificaciones de cada estándar; el LNA se diseña para cubrir los requerimientos de GSM (PCS1900), WCDMA, Bluetooth y WLAN (IEEE 802.11b‐g). Para evaluar el efecto de las no idealidades de la tecnología en el desempeño del LNA, las simulaciones demuestran que el circuito cumple parámetros como NF16dB, S11< ‐5.5dB, S22‐3.3dBm en la banda 1.85‐ 2.48GHz. Para todos los estándares bajo estudio, el consumo adaptivo de potencia varía de 25.3 mW a 53.3mW usando una fuente de alimentación de 1‐V. El patrón geométrico del LNA reconfigurable consume un área de 1.8mm2.Peer Reviewe

    Low-noise amplifiers for integrated multi-mode direct-conversion receivers

    Get PDF
    The evolution of wireless telecommunication systems during the last decade has been rapid. During this time the design driver has shifted towards fast data applications instead of speech. In addition, the different systems may have a limited coverage, for example, limited to urban areas only. Thus, it has become important for a mobile terminal to be able to use different wireless systems, depending on the application chosen and the location of the terminal. The choice of receiver architecture affects the performance, size, and cost of the receiver. The superheterodyne receiver has hitherto been the dominant radio architecture, because of its good sensitivity and selectivity. However, superheterodyne receivers require expensive filters, which, with the existing technologies, cannot be integrated on the same chip as the receiver. Therefore, architectures using a minimum number of external components, such as direct conversion, have become popular. In addition, compared to the superheterodyne architecture, the direct-conversion architecture has benefits when multi-mode receivers, which are described in this thesis, are being designed. In this thesis, the limitations placed on the analog receiver by different system specifications are introduced. The estimations for the LNA specifications are derived from these specifications. In addition, the limitations imposed by different types of receiver architectures are described. The inductively-degenerated LNA is the basis for all the experimental circuits. The different components for this configuration are analyzed and compared to other commonly-used configurations in order to justify the use of an inductively-degenerated LNA. Furthermore, the design issues concerning the LNA-mixer interface in direct-conversion receivers are analyzed. Without knowing these limitations, it becomes difficult to understand the choices made in the experimental circuits. One of the key parts of this thesis describes the design and implementation of a single-chip multi-mode LNA, which is one of the key blocks in multi-mode receivers. The multi-mode structures in this thesis were developed for a direct-conversion receiver where only one system is activated at a time. The LNA interfaces to a pre-select filter and mixers and the different LNA components are analyzed in detail. Furthermore, the design issues related to possible interference from additional systems on single-chip receivers are analyzed and demonstrated. A typical receiver includes variable gain, which can be implemented both in the analog baseband and/or in the RF. If the variable gain is implemented in the RF parts, it is typically placed in the LNA or in a separate gain control stage. Several methods that can be used to implement a variable gain in the LNA are introduced and compared to each other. Furthermore, several of these methods are included in the experimental circuits. The last part of this thesis concentrates on four experimental circuits, which are described in this thesis. The first two chips describe an RF front-end and a direct-conversion receiver for WCDMA applications. The whole receiver demonstrates that it is possible to implement A/D converters on the same chip as sensitive RF blocks without significantly degrading receiver performance. The other two chips describe an RF front-end for WCDMA and GSM900 applications and a direct-conversion receiver for GSM900, DCS1800, PCS1900 and WCDMA systems. These ICs demonstrate the usability of the circuit structure developed and presented in this thesis. The chip area in the last multi-mode receiver is not significantly increased compared to corresponding single-system receivers.reviewe

    Design of an adaptive LNA for hand-held devices in a 1-V 90-nm standard RF CMOS technology: From circuit analysis to layout

    Get PDF
    This paper deals the design of a reconfigurable Low-Noise Amplifier (LNA) for the next generation of wireless hand-held devices by using a lumped circuit approach based on physical laws. The purpose is not only to present simulation results showing the fulfillment of different standard specifications, but also to demonstrate that each design step has a physical meaning such that the mathematical design flow is simple as well as suitable for hand-work in both laboratory and classroom. The circuit under analysis, which is designed according to technological design rules of a 90nm CMOS technology, is a two-stage topology including inductive-source degeneration, MOS-varactor based tuning networks, and programmable bias currents. This proposal, with reduced number of inductors and minimum power dissipation, adapts its performance to different standard specifications; the LNA is designed to cope with the requirements of GSM (PCS1900), WCDMA, Bluetooth and WLAN (IEEE 802.11b-g). In order to evaluate the effect of technology parasitics on the LNA performance, simulation results demonstrate that the LNA features NF16dB, S11-3.3 dBm over the 1.85-2.48 GHz band. For all the standards under study the adaptive power consumption varies from 25.3 mW to 53.3mW at a power supply of 1-V. The layout of the reconfigurable LNA occupies an area of 1.8mm2.Este trabajo presenta el diseño de un amplificador de bajo ruido, LNA (del inglés Low‐Noise Amplifier) reconfigurable para la siguiente generación de dispositivos portátiles de comunicación inalámbricos, usando la aproximación de circuitos concentrados sustentada en leyes físicas. El propósito de este trabajo no es sólo presentar resultados de simulación que muestran el cumplimiento de especificaciones para cada estándar, sino también demostrar que cada paso de diseño tiene un significado físico haciendo que el procedimiento matemático de diseño sea simple y adecuado para el trabajo a mano tanto para actividades en laboratorio como en el aula. El circuito bajo análisis, diseñado en una tecnología CMOS 90nm, consta de dos etapas que incluyen degeneración inductiva de fuente, redes de entonado basadas en varactores MOS, y corrientes de polarización programables. Esta propuesta, con reducido número de inductores y mínima disipación de potencia, adapta su desempeño a las diversas especificaciones de cada estándar; el LNA se diseña para cubrir los requerimientos de GSM (PCS1900), WCDMA, Bluetooth y WLAN (IEEE 802.11b‐g). Para evaluar el efecto de las no idealidades de la tecnología en el desempeño del LNA, las simulaciones demuestran que el circuito cumple parámetros como NF16dB, S11‐3.3dBm en la banda 1.85‐ 2.48GHz. Para todos los estándares bajo estudio, el consumo adaptivo de potencia varía de 25.3 mW a 53.3mW usando una fuente de alimentación de 1‐V. El patrón geométrico del LNA reconfigurable consume un área de 1.8mm2

    Design of a LNA in the frequency band 1.8-2.2GHz in 0.13μm CMOS Technology

    Get PDF
    The subject of this work is a low noise amplifier (LNA), operating in the frequency range 1.8-2.1GHz. The CMOS 0.13μm technology is used in respect to the low cost of the final device. Among the specifications, a variable gain and an adjustable working frequency are required. In particular, four different working modes are provided: 1.8, 1.9 and 2.1GHz high gain and 2.1GHz low gain. The amplifier is designed to be used as first stage of a receiver for mobile telephony. For this reason low power consumption is taken into consideration (low supply voltage and low drain currents). A simple digital circuit, integrated on-chip, is used to select the operating mode of the LNA by means of two input pins. A Noise figure of 1dB is obtained with a supply voltage of 0.8V
    corecore