A 32kb 10T subthreshold SRAM array with bit-interleaving and differential read scheme in 90nm CMOS

We demonstrate a 10T subthreshold SRAM with an efficient bit-interleaving structure for soft-error tolerance and a differential read scheme for improved stability. The 32kb (256128) SRAM array is fabricated in 90nm CMOS and operates at 31.25kHz at 0.18V With more aggressive wordline boosting, the V DD can be reduced to 0.16V At the minimum VDD condition, the operating frequency is 500Hz and the power consumption is 0.123W

Application-Specific SRAM Design Using Output Prediction to Reduce Bit-Line Switching Activity and Statistically Gated Sense Amplifiers for Up to 1.9x Lower Energy/Access

This paper presents an application-specific SRAM design targeted towards applications with highly correlated data (e.g., video and imaging applications). A prediction-based reduced bit-line switching activity scheme is proposed to reduce switching activity on the bit-lines based on the proposed bit-cell and array structure. A statistically gated sense-amplifier approach is used to exploit signal statistics on the bit-lines to reduce energy consumption of the sensing network. These techniques provide up to 1.9 × lower energy/access when compared with an 8T SRAM. These savings are in addition to the savings that are achieved through voltage scaling and demonstrate the advantages of an application-specific SRAM design.Texas Instruments Incorporate

Ultra-Low Power Circuit Design for Cubic-Millimeter Wireless Sensor Platform.

Modern daily life is surrounded by smaller and smaller computing devices. As Bell’s Law predicts, the research community is now looking at tiny computing platforms and mm3-scale sensor systems are drawing an increasing amount of attention since they can create a whole new computing environment. Designing mm3-scale sensor nodes raises various circuit and system level challenges and we have addressed and proposed novel solutions for many of these challenges to create the first complete 1.0mm3 sensor system including a commercial microprocessor. We demonstrate a 1.0mm3 form factor sensor whose modular die-stacked structure allows maximum volume utilization. Low power I2C communication enables inter-layer serial communication without losing compatibility to standard I2C communication protocol. A dual microprocessor enables concurrent computation for the sensor node control and measurement data processing. A multi-modal power management unit allowed energy harvesting from various harvesting sources. An optical communication scheme is provided for initial programming, synchronization and re-programming after recovery from battery discharge. Standby power reduction techniques are investigated and a super cut-off power gating scheme with an ultra-low power charge pump reduces the standby power of logic circuits by 2-19× and memory by 30%. Different approaches for designing low-power memory for mm3-scale sensor nodes are also presented in this work. A dual threshold voltage gain cell eDRAM design achieves the lowest eDRAM retention power and a 7T SRAM design based on hetero-junction tunneling transistors reduces the standby power of SRAM by 9-19× with only 15% area overhead. We have paid special attention to the timer for the mm3-scale sensor systems and propose a multi-stage gate-leakage-based timer to limit the standard deviation of the error in hourly measurement to 196ms and a temperature compensation scheme reduces temperature dependency to 31ppm/°C. These techniques for designing ultra-low power circuits for a mm3-scale sensor enable implementation of a 1.0mm3 sensor node, which can be used as a skeleton for future micro-sensor systems in variety of applications. These microsystems imply the continuation of the Bell’s Law, which also predicts the massive deployment of mm3-scale computing systems and emergence of even smaller and more powerful computing systems in the near future.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/91438/1/sori_1.pd

Design and Analysis of Robust Low Voltage Static Random Access Memories.

Static Random Access Memory (SRAM) is an indispensable part of most modern VLSI designs and dominates silicon area in many applications. In scaled technologies, maintaining high SRAM yield becomes more challenging since they are particularly vulnerable to process variations due to 1) the minimum sized devices used in SRAM bitcells and 2) the large array sizes. At the same time, low power design is a key focus throughout the semiconductor industry. Since low voltage operation is one of the most effective ways to reduce power consumption due to its quadratic relationship to energy savings, lowering the minimum operating voltage (Vmin) of SRAM has gained significant interest. This thesis presents four different approaches to design and analyze robust low voltage SRAM: SRAM analysis method improvement, SRAM bitcell development, SRAM peripheral optimization, and advance device selection. We first describe a novel yield estimation method for bit-interleaved voltage-scaled 8-T SRAMs. Instead of the traditional trade-off between write and read, the trade-off between write and half select disturb is analyzed. In addition, this analysis proposes a method to find an appropriate Write Word-Line (WWL) pulse width to maximize yield. Second, low leakage 10-T SRAM with speed compensation scheme is proposed. During sleep mode of a sensor application, SRAM retaining data cannot be shut down so it is important to minimize leakage in SRAM. This work adopts several leakage reduction techniques while compensating performance. Third, adaptive write architecture for low voltage 8-T SRAMs is proposed. By adaptively modulating WWL width and voltage level, it is possible to achieve low power consumption while maintaining high yield without excessive performance degradation. Finally, low power circuit design based on heterojunction tunneling transistors (HETTs) is discussed. HETTs have a steep subthreshold swing beneficial for low voltage operation. Device modeling and design of logic and SRAM are proposed.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/91569/1/daeyeonk_1.pd

Ultra-low-power SRAM design in high variability advanced CMOS

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.Cataloged from PDF version of thesis.Includes bibliographical references (p. 163-181).Embedded SRAMs are a critical component in modern digital systems, and their role is preferentially increasing. As a result, SRAMs strongly impact the overall power, performance, and area, and, in order to manage these severely constrained trade-offs, they must be specially designed for target applications. Highly energy-constrained systems (e.g. implantable biomedical devices, multimedia handsets, etc.) are an important class of applications driving ultra-low-power SRAMs. This thesis analyzes the energy of an SRAM sub-array. Since supply- and threshold-voltage have a strong effect, targets for these are established in order to optimize energy. Despite the heavy emphasis on leakage-energy, analysis of a high-density 256x256 sub-array in 45nm LP CMOS points to two necessary optimizations: (1) aggressive supply-voltage reduction (in addition to Vt elevation), and (2) performance enhancement. Important SRAM metrics, including read/write/hold-margin and read-current, are also investigated to identify trade-offs of these optimizations. Based on the need to lower supply-voltage, a 0.35V 256kb SRAM is demonstrated in 65nm LP CMOS. It uses an 8T bit-cell with peripheral circuit-assists to improve write-margin and bit-line leakage. Additionally, redundancy, to manage the increasing impact of variability in the periphery, is proposed to improve the area-offset trade-off of sense-amplifiers, demonstrating promise for highly advanced technology nodes. Based on the need to improve performance, which is limited by density constraints, a 64kb SRAM, using an offset-compensating sense-amplifier, is demonstrated in 45nm LP CMOS with high-density 0.25[mu]m2 bit-cells.(cont.) The sense-amplifier is regenerative, but non -strobed, overcoming timing uncertainties limiting performance, and it is single-ended, for compatibility with 8T cells. Compared to a conventional strobed sense-amplifier, it achieves 34% improvement in worst-case access-time and 4x improvement in the standard deviation of the access-time.by Naveen Verma.Ph.D

Low-power and application-specific SRAM design for energy-efficient motion estimation

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2012.Cataloged from PDF version of thesis.Includes bibliographical references (p. 181-189).Video content is expected to account for 70% of total mobile data traffic in 2015. High efficiency video coding, in this context, is crucial for lowering the transmission and storage costs for portable electronics. However, modern video coding standards impose a large hardware complexity. Hence, energy-efficiency of these hardware blocks is becoming more critical than ever before for mobile devices. SRAMs are critical components in almost all SoCs affecting the overall energy-efficiency. This thesis focuses on algorithm and architecture development as well as low-power and application-specific SRAM design targeting motion estimation. First, a motion estimation design is considered for the next generation video standard, HEVC. Hardware cost and coding efficiency trade-offs are quantified and an optimum design choice between hardware complexity and coding efficiency is proposed. Hardware-efficient search algorithm, shared search range across CU engines and pixel pre-fetching algorithms provide 4.3x area, 56x on-chip bandwidth and 151 x off-chip bandwidth reduction. Second, a highly-parallel motion estimation design targeting ultra-low voltage operation and supporting AVC/H.264 and VC-1 standards are considered. Hardware reconfigurability along with frame and macro-block parallel processing are implemented for this engine to maximize hardware sharing between multiple standards and to meet throughput constraints. Third, in the context of low-power SRAMs, a 6T and an 8T SRAM are designed in 28nm and 45nm CMOS technologies targeting low voltage operation. The 6T design achieves operation down to 0.6V and the 8T design achieves operation down to 0.5V providing ~ 2.8x and ~ 4.8x reduction in energy/access respectively. Finally, an application-specific SRAM design targeted for motion estimation is developed. Utilizing the correlation of pixel data to reduce bit-line switching activity, this SRAM achieves up to 1.9x energy savings compared to a similar conventional 8T design. These savings demonstrate that application-specific SRAM design can introduce a new dimension and can be combined with voltage scaling to maximize energy-efficiency.by Mahmut Ersin Sinangil.Ph.D

Low-voltage embedded biomedical processor design

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2010.Cataloged from PDF version of thesis.Includes bibliographical references (p. 180-190).Advances in mobile electronics are fueling new possibilities in a variety of applications, one of which is ambulatory medical monitoring with body-worn or implanted sensors. Digital processors on such sensors serve to analyze signals in real-time and extract key features for transmission or storage. To support diverse and evolving applications, the processor should be flexible, and to extend sensor operating lifetime, the processor should be energy-efficient. This thesis focuses on architectures and circuits for low power biomedical signal processing. A general-purpose processor is extended with custom hardware accelerators to reduce the cycle count and energy for common tasks, including FIR and median filtering as well as computing FFTs and mathematical functions. Improvements to classic architectures are proposed to reduce power and improve versatility: an FFT accelerator demonstrates a new control scheme to reduce datapath switching activity, and a modified CORDIC engine features increased input range and decreased quantization error over conventional designs. At the system level, the addition of accelerators increases leakage power and bus loading; strategies to mitigate these costs are analyzed in this thesis. A key strategy for improving energy efficiency is to aggressively scale the power supply voltage according to application performance demands. However, increased sensitivity to variation at low voltages must be mitigated in logic and SRAM design. For logic circuits, a design flow and a hold time verification methodology addressing local variation are proposed and demonstrated in a 65nm microcontroller functioning at 0.3V. For SRAMs, a model for the weak-cell read current is presented for near-V supply voltages, and a self-timed scheme for reducing internal bus glitches is employed with low leakage overhead. The above techniques are demonstrated in a 0.5-1.OV biomedical signal processing platform in 0.13p-Lm CMOS. The use of accelerators for key signal processing enabled greater than 10x energy reduction in two complete EEG and EKG analysis applications, as compared to implementations on a conventional processor.by Joyce Y. S. Kwong.Ph.D