A -5 dBm 400MHz OOK Transmitter for Wireless Medical Application

A 400 MHz high efficiency transmitter forwireless medical application is presented in this paper. Transmitter architecture with high-energy efficiencies isproposed to achieve high data rate with low powerconsumption. In the on-off keying transmitters, the oscillatorand power amplifier are turned off when the transmittersends 0 data. The proposed class-e power amplifier has highefficiency for low level output power. The proposed on-offkeying transmitter consumes 1.52 mw at -5 dBm output by 40Mbps data rate and energy consumption 38 pJ/bit. Theproposed transmitter has been designed in 0.18µm CMOStechnology

Low-Power High-Data-Rate Transmitter Design for Biomedical Application

Ph.DDOCTOR OF PHILOSOPH

Low power CMOS IC, biosensor and wireless power transfer techniques for wireless sensor network application

The emerging field of wireless sensor network (WSN) is receiving great attention due to the interest in healthcare. Traditional battery-powered devices suffer from large size, weight and secondary replacement surgery after the battery life-time which is often not desired, especially for an implantable application. Thus an energy harvesting method needs to be investigated. In addition to energy harvesting, the sensor network needs to be low power to extend the wireless power transfer distance and meet the regulation on RF power exposed to human tissue (specific absorption ratio). Also, miniature sensor integration is another challenge since most of the commercial sensors have rigid form or have a bulky size. The objective of this thesis is to provide solutions to the aforementioned challenges

A 2.4GHz ULP OOK single-chip transceiver for healthcare applications

Wireless body-area networks (WBAN) are used for communication among sensor nodes operating on, in or around the human body, e.g. for healthcare purposes. In view of energy autonomy, the total energy consumption of the sensor nodes should be minimized. Because of their low complexity, a combination of the super-regenerative (SR) principle [1-3] and OOK modulation enables ultra low power (ULP) consumption. This work presents a 2.4GHz ULP OOK single chip transceiver for WBAN applications. A block diagram of the implemented transceiver is shown in Fig. 26.3.1. Next to the direct modulation TX [4] and SR RF [5] front-ends, this work integrates analog and digital baseband, PLL functionality and additional programmability for flexible data rates, and achieves ultra-low power consumption for the overall system

Multi-channel ultra-low-power receiver architecture for body area networks

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2011.Cataloged from PDF version of thesis.Includes bibliographical references (p. 85-91).In recently published integrated medical monitoring systems, a common thread is the high power consumption of the radio compared to the other system components. This observation is indicative of a natural place to attempt a reduction in system power. Narrowband receivers in-particular can enjoy significant power reduction by employing high-Q bulk acoustic resonators as channel select filters directly at RF, allowing down-stream analog processing to be simplified, resulting in better energy efficiency. But for communications in the ISM bands, it is important to employ multiple frequency channels to permit frequency-division-multiplexing and provide frequency diversity in the face of narrowband interferers. The high-Q nature of the resonators means that frequency tuning to other channels in the same band is nearly impossible; hence, a new architecture is required to address this challenge. A multi-channel ultra-low power OOK receiver for Body Area Networks (BANs) has been designed and tested. The receiver multiplexes three Film Bulk Acoustic Resonators (FBARs) to provide three channels of frequency discrimination, while at the same time offering competitive sensitivity and superior energy efficiency in this class of BAN receivers. The high-Q parallel resonance of each resonator determines the passband. The resonator's Q is on the order of 1000 and its center frequency is approximately 2.5 GHz, resulting in a -3 dB bandwidth of roughly 2.5 MHz with a very steep rolloff. Channels are selected by enabling the corresponding LNA and mixer pathway with switches, but a key benefit of this architecture is that the switches are not in series with the resonator and do not de-Q the resonance. The measured 1E-3 sensitivity is -64 dBm at 1 Mbps for an energy efficiency of 180 pJ/bit. The resonators are packaged beside the CMOS using wirebonds for the prototype.by Phillip Michel Nadeau.S.M

A 2.4GHz ULP OOK single-chip transceiver for healthcare applications

This paper describes an ultra-low power (ULP) single chip transceiver for wireless body area network (WBAN) applications. It supports on-off keying (OOK) modulation, and it operates in the 2.36–2.4 GHz medical BAN and 2.4–2.485 GHz ISM bands. It is implemented in 90 nm CMOS technology. The direct modulated transmitter transmits OOK signal with 0 dBm peak power, and it consumes 2.59 mW with 50% OOK. The transmitter front-end supports up to 10 Mbps. The transmitter digital baseband enables digital pulse-shaping to improve spectrum efficiency. The super-regenerative receiver front-end supports up to 5 Mbps with $-75~{rm dBm}$ sensitivity. Including the digital part, the receiver consumes 715 $mu {rm W}$ at 1 Mbps data rate, oversampled at 3 MHz. At the system level the transceiver achieves ${rm PER}=10 ^{-2}$ at 25 meters line of site with 62.5 kbps data rate and 288 bits packet size. The transceiver is integrated in an electrocardiogram (ECG) necklace to monitor the heart's electrical property

Energy Aware RF Transceiver for Wireless Body Area Networks (WBAN)

Ph.DDOCTOR OF PHILOSOPH

RF Integrated Circuits for Energy Autonomous Sensor Nodes.

The exponential growth in the semiconductor industry has enabled computers to pervade our everyday lives, and as we move forward many of these computers will have form factors much smaller than a typical laptop or smartphone. Sensor nodes will soon be deployed ubiquitously, capable of capturing information of their surrounding environment. The next step is to connect all these different nodes together into an entire interconnected system. This “Internet of Things” (IoT) vision has incredible potential to change our lives commercially, societally, and personally. The backbone of IoT is the wireless sensor node, many of which will operate under very rigorous energy constraints with small batteries or no batteries at all. It has been shown that in sensor nodes, radio communication is one of the biggest bottlenecks to ultra-low power design. This research explores ways to reduce energy consumption in radios for wireless sensor networks, allowing them to run off harvested energy, while maintaining qualities that will allow them to function in a real world, multi-user environment. Three different prototypes have been designed demonstrating these techniques. The first is a sensitivity-reduced nanowatt wake-up radio which allows a sensor node to actively listen for packets even when the rest of the node is asleep. CDMA codes and interference rejection reduce the potential for energy-costly false wake-ups. The second prototype is a full transceiver for a body-worn EKG sensor node. This transceiver is designed to have low instantaneous power and is able to receive 802.15.6 Wireless Body Area Network compliant packets. It uses asymmetric communication including a wake-up receiver based on the previous design, UWB transmitter and a communication receiver. The communication receiver has 10 physical channels to avoid interference and demodulates coherent packets which is uncommon for low power radios, but dictated by the 802.15.6 standard. The third prototype is a long range transceiver capable of >1km communication range in the 433MHz band and able to interface with an existing commercial radio. A digitally assisted baseband demodulator was designed which enables the ability to perform bit-level as well as packet-level duty cycling which increases the radio's energy efficiency.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/110432/1/nerobert_1.pd

Design of Low-Power Short-Distance Transceiver for Wireless Sensor Networks

Ph.DDOCTOR OF PHILOSOPH