SCR Blocking Pulse Gate Amplifier-Patent

Silicon controlled rectifier pulse gate amplifier for blocking false gating caused by negative transient voltage

Method for measuring alternator voltage transients

Transient voltage detection circuit measures voltage excursions and recovery times resulting from step-load changes applied to a combination alternator-voltage regulator

Correlation of transient spectra with performance in coaxial plasma guns

Two channel transient voltage digitizer for correlation of transient spectra with performance in coaxial, argon plasma gun

Circuit protection devices for transient suppression

The Electromer Corporation has developed a series of transient voltage suppression components based on a patented, specially formulated PolyClamp (trademark) material. PolyClamp components are a new class of transient voltage surge suppressors that extend the range of protection offered by transients protectors. The PolyClamp transient surge suppressors provide low capacitance, high energy capability, and packaging flexibility. A wide variety of applications can be protected. A tube and ferrule configuration was designed to be used with MIL/Aerospace style connectors and is designed to meet the applicable environmental, mechanical, and electrical requirements as defined by the United States and European defence standards performance requirements. Here, PolyClamp is compared with current transient surge suppressors. Typical performance and design are discussed

Optimal Battery Energy Storage Placement for Transient Voltage Stability Enhancement

A placement problem for multiple Battery Energy Storage System (BESS) units is formulated towards power system transient voltage stability enhancement in this paper. The problem is solved by the Cross-Entropy (CE) optimization method. A simulation-based approach is adopted to incorporate higher-order dynamics and nonlinearities of generators and loads. The objective is to maximize the voltage stability index, which is set up based on certain grid-codes. Formulations of the optimization problem are then discussed. Finally, the proposed approach is implemented in MATLAB/DIgSILENT and tested on the New England 39-Bus system. Results indicate that installing BESS units at the optimized location can alleviate transient voltage instability issue compared with the original system with no BESS. The CE placement algorithm is also compared with the classic PSO (Particle Swarm Optimization) method, and its superiority is demonstrated in terms of fewer iterations for convergence with better solution qualities.Comment: This paper has been accepted by the 2019 IEEE PES General Meeting at Atlanta, GA in August 201

Optimization of Battery Energy Storage to Improve Power System Oscillation Damping

A placement problem for multiple Battery Energy Storage System (BESS) units is formulated towards power system transient voltage stability enhancement in this paper. The problem is solved by the Cross-Entropy (CE) optimization method. A simulation-based approach is adopted to incorporate higher-order dynamics and nonlinearities of generators and loads. The objective is to maximize the voltage stability index, which is setup based on certain grid-codes. Formulations of the optimization problem are then discussed. Finally, the proposed approach is implemented in MATLAB/DIgSILENT and tested on the New England 39-Bus system. Results indicate that installing BESS units at the optimized location can alleviate transient voltage instability issue compared with the original system with no BESS. The CE placement algorithm is also compared with the classic PSO (Particle Swarm Optimization) method, and its superiority is demonstrated in terms of a faster convergence rate with matched solution qualities.Comment: This paper has been accepted by IEEE Transactions on Sustainable Energy and now still in online-publication phase, IEEE Transactions on Sustainable Energy. 201

Temperature-Dependent Macromodels of Digital Device

This paper addresses the development of a temperature-dependent parametric macromodel for the output ports of a digital IC. The model parameters are estimated from port transient voltage and current waveforms by means of a simple and efficient procedure. The obtained models are implemented as SPICE subcircuits. They perform at an accuracy and efficiency level suitable for system-level SI and EMC simulation

Investigation of surge propagation in transient voltage surge suppressors and experimental verification

An on-going question in the field of surge protection study is how to predict incipient failure of power electronics in the event of a short time, high voltage, and high energy transient surge propagation. The work presented in this thesis addresses the above question by investigating how a high voltage transient surge, whose duration is in the microseconds range, will propagate through the two-level transient voltage suppressor system that is intended to protect sophisticated electronics situated close to the service entrance of a building. In this work the energy patterns relevant to the individual components of the system are evaluated using numerical methods and some of the results are also compared with those obtained using SPICE simulations. Although several mathematical models for surge protection components are discussed in the literature and some device specific ones are provided by manufacturers, there is no evidence to show that a complete analysis, using any such model, has been performed to predict the energy absorptions and associated time lags between the components in a TVSS. Numerical simulation techniques using MATLAB are used to estimate the energy absorption and associated time delays in relation to the propagated transient surge, in individual components of a transient voltage surge suppressor. This study develops mathematical models for particular nonlinear transient surge absorbing elements, specifically for the metal oxide varistor and transient voltage suppressor diode, formulates the state equations which are used to numerically simulate several instances of the transient voltage surge suppressor system, and presents simulation results. All results are validated experimentally using a lightning surge simulator. The outcomes established using the two approaches indicate that the theoretical energy calculations are within 10% of the experimental validations for the metal oxide varistor, which is the main energy absorbing element in the system. The remaining energy distributions in the line-filter components and the transient voltage suppressor diode, which are at least 10 times smaller, are all within 20% of the experimental results. The times at which, the metal oxide varistor and the transient voltage suppressor diode switches to heavy conduction mode are also simulated accurately

Factors affecting the operation of laser-triggered gas switch (LTGS) with multi-electrode spark gap

Multi-electrode spark switches can be used for switching applications at elevated voltages or for command triggering. Symmetrical field graded electrodes allow the electrical stress across individual gaps to be controlled, thus maximising the hold off voltage and reducing switch pre-fire. The paper considers some aspects of multielectrode switch design and their influence on switching behavior. Non-symmetrical, uni-directional electrode topologies can be employed with advantages over traditional symmetrical design. The choice of working gas and gas pressure can influence switching performance in terms of delay-time and jitter. Transient analysis of switch characteristics has been undertaken in order to understand multi-electrode switching