3,603 research outputs found
Anisotropic adaptivity for the finite element solutions of three-dimensional convection-dominated problems
Convection-dominated problems are typified by the presence of strongly directional features such as shock waves or boundary layers. Resolution of numerical solutions using an isotropic mesh can lead to unnecessary refinement in directions parallel to such features. This is particularly important in three dimensions where the grid size increases rapidly during conventional isotropic refinement procedures.
In this work, we investigate the use of adaptive finite element methods using anisotropic mesh refinement strategies for convection-dominated problems. The strategies considered here aim to resolve directional features without excessive resolution in other directions, and hence achieve accurate solutions more efficiently. Two such strategies are described here: the first based on minimization of the least-squares residual; the second based on minimizing a finite element error estimate. These are incorporated into an hr-adaptive finite element method and tested on a simple model problem
Numerical methods and a computer program for subsonic and supersonic aerodynamic design and analysis of wings with attainable thrust considerations
This paper describes methodology and an associated computer program for the design of wing lifting surfaces with attainable thrust taken into consideration. The approach is based on the determination of an optimum combination of a series of candidate surfaces rather than the more commonly used candidate loadings. Special leading-edge surfaces are selected to provide distributed leading-edge thrust forces which compensate for any failure to achieve the full theoretical leading-edge thrust, and a second series of general candidate surfaces is selected to minimize drag subject to constraints on the lift coefficient and, if desired, on the pitching moment coefficient. A primary purpose of the design approach is the introduction of attainable leading-edge thrust considerations so that relatively mild camber surfaces may be employed in the achievement of aerodynamic efficiencies comparable to those attainable if full theoretical leading-edge thrust could be achieved. The program provides an analysis as well as a design capability and is applicable to both subsonic and supersonic flow
Aerodynamic design and analysis of the AST-204, AST-205, and AST-206 blended wing-fuse large supersonic transport configuration concepts
The aerodynamic design and analysis of three blended wing-fuselage supersonic cruise configurations providing four, five, and six abreast seating was conducted using a previously designed supersonic cruise configuration as the baseline. The five abreast configuration was optimized for wave drag at a Mach number of 2.7. The four and six abreast configurations were also optimized at Mach 2.7, but with the added constraint that the majority of their structure be common with the five abreast configuration. Analysis of the three configurations indicated an improvement of 6.0, 7.5, and 7.7 percent in cruise lift-to-drag ratio over the baseline configuration for the four, five, and six abreast configurations, respectively
Aerodynamic design and analysis of the AST-200 supersonic transport configuration concept
The design and analysis of a supersonic transport configuration was conducted using linear theory methods in conjunction with appropriate constraints. Wing optimization centered on the determination of the required twist and camber and proper integration of the wing and fuselage. Also included in the design are aerodynamic refinements to the baseline wing thickness distribution and nacelle shape. Analysis to the baseline and revised configurations indicated an improvement in lift-to-drag ratio of 0.36 at the Mach 2.7 cruise condition. Validation of the design is planned through supersonic wing tunnel tests
An aerodynamic analysis computer program and design notes for low speed wing flap systems
The expanded capabilities for analysis and design of low speed flap systems afforded by recent modifications of an existing computer program is described. The program provides for the simultaneous analysis of up to 25 pairs of leading-edge and trailing-edge flap deflection schedules. Among other new features of the program are a revised attainable thrust estimation method to provide more accurate predictions for low Mach numbers, and a choice of three options for estimation of leading-edge separation vortex flow effects. Comparison of program results with low speed experimental data for an arrow wing supersonic cruise configuration with leading-edge and trailing-edge flaps showed good agreement over most of the range of flap deflections. Other force data comparisons and an independent study of airfoil and wing pressure distributions indicated that wind-tunnel measurements of the aerodynamic performance of twisted and cambered wings and wings with leading-edge flaps can be very sensitive to Reynolds number effects
A multilevel approach for obtaining locally optimal finite element meshes
In this paper we consider the adaptive finite element solution of a general class of variational problems using a combination of node insertion, node movement and edge swapping. The adaptive strategy that is proposed is based upon the construction of a hierarchy of locally optimal meshes starting with a coarse grid for which the location and connectivity of the nodes is optimized.
This grid is then locally refined and the new mesh is optimized in the same manner. Results presented indicate that this approach is able to produce better meshes than those possible by more conventional adaptive strategies and in a relatively efficient manner
A computer program for wing subsonic aerodynamic performance estimates including attainable thrust and vortex lift effects
Numerical methods incorporated into a computer program to provide estimates of the subsonic aerodynamic performance of twisted and cambered wings of arbitrary planform with attainable thrust and vortex lift considerations are described. The computational system is based on a linearized theory lifting surface solution which provides a spanwise distribution of theoretical leading edge thrust in addition to the surface distribution of perturbation velocities. The approach used relies on a solution by iteration. The method also features a superposition of independent solutions for a cambered and twisted wing and a flat wing of the same planform to provide, at little additional expense, results for a large number of angles of attack or lift coefficients. A previously developed method is employed to assess the portion of the theoretical thrust actually attainable and the portion that is felt as a vortex normal force
Regional Differences in Wild North American River Otter (Lontra canadensis) Behavior and Communication
This study focuses on the vocalization repertoires of wild North American river otters (Lontra canadensis) in New York and California. Although they are the same species, these two established populations of river otters are separated by a significant distance and are distinct from one another. River otters are semi-aquatic social predators that can be found throughout North America. This is the first study to examine the vocalizations of wild river otters, and results are compared across field sites in the different regions. River otter vocalizations and behaviors in New York were recorded using Bushnell Aggressor trail cameras that were placed in areas of moderate to high river otter activity. The River Otter Ecology Project, a nonprofit organization studying river otter populations in Marin County, provided the otter videos from California. Recorded vocalizations were separated into categories based on their appearance on a spectrogram and parameters including frequency and duration were measured for each call. Behaviors were identified in all New York videos and during vocalizations in both New York and California videos. Four call types (chuckle, hah, chirp, and whine) were recorded in both California and New York otters. An additional call (chirpwhine) was recorded only in the California population. Otters in both populations produced chuckles while traveling, scentmarking, and investigating. Hahs were produced during disturbance, food, play, and rub behaviors. Otters were most likely to produce chirps when they were stationary and alone. Hahs were most likely to occur in pairs, and chuckles and whines were more likely to occur among groups of 3 or more otters. This study not only contributes to the limited knowledge that exists on the North American river otter vocalization repertoire, but also bridges the gap between animal acoustics and behaviors, providing behavioral context for this elusive species’ most common call types in the wild
- …