Transport and magnetic Jc of MgB2 strands and small helical coils

The critical current densities of MgB2 monofilamentary strands with and without SiC additions were measured at 4.2 K. Additionally, magnetic Jc at B = 1 T was measured from 4.2 K to 40 K. Various heat treatment times and temperatures were investigated for both short samples and small helical coils. SiC additions were seen to improve high field transport Jc at 4.2 K, but improvements were not evident at 1 T at any temperature. Transport results were relatively insensitive to heat treatment times and temperatures for both short samples and coils in the 700C to 900C range.Comment: 8 text pages, 1 table, 4 fig

Properties of recent IBAD-MOCVD Coated Conductors relevant to their high field, low temperature magnet use

BaZrO3 (BZO) nanorods are now incorporated into production IBAD-MOCVD coated conductors. Here we compare several examples of both BZO-free and BZO-containing coated conductors using critical current (Ic) characterizations at 4.2 K over their full angular range up to fields of 31 T. We find that BZO nanorods do not produce any c-axis distortion of the critical current density Jc(theta) curve at 4.2 K at any field, but also that pinning is nevertheless strongly enhanced compared to the non-BZO conductors. We also find that the tendency of the ab-plane Jc(theta) peak to become cusp-like is moderated by BZO and we define a new figure of merit that may be helpful for magnet design - the OADI (Off-Axis Double Ic), which clearly shows that BZO broadens the ab-plane peak and thus raises Jc 5-30{\deg} away from the tape plane, where the most critical approach to Ic occurs in many coil designs. We describe some experimental procedures that may make critical current Ic tests of these very high current tapes more tractable at 4.2 K, where Ic exceeds 1000 A even for 4 mm wide tape with only 1 micron thickness of superconductor. A positive conclusion is that BZO is very beneficial for the Jc characteristics at 4.2 K, just as it is at higher temperatures, where the correlated c-axis pinning effects of the nanorods are much more obvious

Development of Y-Ba-Cu-O Superconductors for Magnetic Bearings

The material requirements, material manufacturing and magnetic properties that are relevant to fabrication of High Temperature Superconductor (HTS) magnetic bearings have been discussed. It is found that the seeded-melt-texturing method can be used to fabricate the single domain material that is required to achieve the best magnetic properties. Trapped-field mapping has been used as a non-destructive tool to determine the single-domain nature of the HTS material and quantity of the HTS disks. Both the trapped field and the levitation force of the Y-Ba-Cu-O disks are found to be strongly sensitive to the oxygen content

Accelerator Magnet Development Based on COMB Technology with STAR Wires

This paper reports progress in the development of COMB magnet technology with STAR wires. A two-layer dipole magnet with 60 mm clear bore has been recently fabricated and tested in liquid nitrogen. The purpose of the test was to determine what kind of critical current degradation occurs in the process of winding the STAR wire into the COMB structure.Comment: CEC/ICMC2

Differential Effect of Contrast Polarity Reversals in Closed Squares and Open L-Junctions

Scene segmentation depends on interaction between geometrical and photometric factors. It has been shown that reversals in contrast polarity at points of highest orientation discontinuity along closed contours significantly impair shape discrimination performance, while changes in contrast polarity at straight(er) contour segments do not have such deleterious effects (Spehar, 2002). Here we employ (semi) high resolution fMRI (1.5 mm × 1.5 mm × 1.5 mm) to investigate the neuronal substrate underlying these perception effects. Stimuli consisted of simple elements (a) squares with contrast reversals along straight segments; (b) squares with contrast reversals in the corner (highest orientation discontinuity); (c) L-Junctions with contrast reversals along the straight ends; (d) L-Junctions with contrast reversals in the corner. Element with contrast polarity reversals are easy to distinguish though appear geometrically equivalent. For squares with contrast polarity reversals only along straight lines we find significantly lower BOLD modulation compared to any of the control conditions, which show similar responses to each other. In the light of previous psychophysical work (Elder and Zucker, 1993; Spehar, 2002) we speculate that this effect is due to closure perception. We observe this across a wide range of areas on occipital cortex

Engineering current density over 5 kA mm-2 at 4.2 K, 14 T in thick film REBCO tapes

We report on remarkably high in-field performance at 4.2 K achieved in >4 μm thick rare earth barium copper oxide (REBCO) samples with Zr addition. Two different samples have been measured independently at Lawrence Berkeley National Laboratory and the National High Magnetic Field Laboratory, achieving critical current densities (J ) of 12.21 MA cm and 12.32 MA cm at 4.2 K, 14 T (), respectively, which corresponds to equivalent critical current (I ) values of 2247 and 2119 A/4 mm. These I values are about two times higher than the best reported performance of REBCO tapes to date and more than five times higher than the commercial HTS tapes reported in a recent study. The measured J values, with a pinning force of ∼1.7 T N m are almost identical to the highest value reported for thin (∼1 μm thick) REBCO at the field and temperature, but extended to very thick (>4 μm) films. This results in an engineering current density (J ) above 5 kA mm at 4.2 K, 14 T, which is more than five times higher than Nb Sn and nearly four times higher than the highest reported value of all superconductors other than REBCO at this field and temperature. The reported results have been achieved by utilizing an advanced metal organic chemical vapor deposition system. This study demonstrates the remarkable level of in-field performance achievable with REBCO conductors at 4.2 K and strong potential for high-field magnet applications. c c c c e 3 -2 -2 -3 -

Development of Prototype HTS Components for Magnetic Suspension Applications

We have concentrated on developing prototype lengths of bismuth and thallium based silver sheathed superconductors by the powder-in-tube approach to fabricate high temperature superconducting (HTS) components for magnetic suspension applications. Long lengths of mono and multi filament tapes are presently being fabricated with critical current densities useful for maglev and many other applications. We have recently demonstrated the prototype manufacture of lengths exceeding 1 km of Bi-2223 multi filament conductor. Long lengths of thallium based multi-filament conductor have also been fabricated with practical levels of critical current density and improved field dependence behavior. Test coils and magnets have been built from these lengths and characterized over a range of temperatures and background fields to determine their performance. Work is in progress to develop, fabricate and test HTS windings that will be suitable for magnetic suspension, levitation and other electric power related applications