Optimization of the Core Compound for Ytterbium Ultra-Short Cavity Fiber Lasers

Highly ytterbium-, aluminum- and phosphorus-co-doped silica fibers with low optical losses were fabricated by the MCVD method, utilizing an all-gas-phase deposition technique. Optical and laser properties of the active fibers with a phosphosilicate and aluminophosphosilicate glass cores doped with 1.85 mol% and 1.27 mol% Yb2O3 were thoroughly investigated. With the help of hydrogen loading, it was possible to induce highly reflective Bragg grating in both fiber samples using the standard phase-mask technique and 193 nm-UV laser irradiation. The ultra-short (less than 2 cm long) Fabry–Perot laser cavities were fabricated by inscribing two fiber Bragg gratings (highly and partially reflective FBGs) directly in the core of the fiber samples. The highest pump-to-signal conversion efficiency of 47% was demonstrated in such laser configuration using phosphosilicate fiber. The reasons for the low efficiency of aluminophosphosilicate fiber are discussed

High-power fiber laser materials: Influence of fabrication methods and codopants on optical properties

In this contribution the influence of fabrication technique (solution doping, gas-phase doping) and the choice of suitable material systems (Al, P, Yb:SiO2 and Al, F, Yb:SiO2) for high power fiber laser materials on their optical properties is analyzed. The materials under analysis contain low amounts of codopants (Yb < 0.15 mol%, other <1.2 mol%). The effects on refractive index, attenuation, absorption and emission cross section as well as on photodarkening are addressed. The main part concerns with the analysis of photodarkening, in fact the evolution of individual defect centers are spectrally and temporally investigated by means of 2D curve fitting. It is suggested that this spectro-temporal fitting procedure can lead to new insights in the development of photodarkening on a level of the defects themselves

Femtosecond Laser Fabrication of Silver Microstructures in Nanoporous Glasses

This paper presents the results of studying the process of laser formation of microstructures from silver nanoparticles in nanoporous quartz glasses. Glass samples were impregnated with organometallic molecules Ag(hfac)COD in a supercritical carbon dioxide environment. The formation of point and linear microstructures was carried out by high-frequency (70 MHz) femtosecond laser radiation with a wavelength of 525 nm and energy in the pulse up to 1 nJ. It was found that the formation of microstructures occurs due to photo- and thermal decomposition of precursor molecules with the formation of plasmonic silver nanoparticles. It is shown that the developed temperatures can exceed the melting point of glass, which leads to the appearance of microstructures with altered refractive index. A qualitative model explaining the individual stages of cluster formation in the glass volume under point laser impact is presented

UV-induced stress changes in phosphorous-doped fibers drawn at different drawing tensions

Stress changes in hydrogenated phosphorous-doped fibers after Bragg grating inscription have been measured. Fibers with three different drawing tensions have been investigated. The core stress was found to increase independently of the initial stress stat

Random Laser Based on Ytterbium-Doped Fiber with a Bragg Grating Array as the Source of Continuous-Wave 976 nm Wavelength Radiation

A random narrow-linewidth lasing at a wavelength of 976 nm was obtained in an ytterbium-doped germanophosphosilicate fiber with an array of weakly reflecting fiber Bragg gratings (FBGs). A random laser cavity was formed by implementing the standard phase mask method of FBG inscription directly during the fiber drawing process. The UV radiation pulses of a KrF excimer laser (248 nm wavelength) synchronized with the fiber drawing speed were used to fabricate the in-fiber array of hundreds of similar FBGs. The developed laser’s slope efficiency in the backward-pumping scheme was measured as high as 33%. The stable continuous-wave operation mode of the laser was detected. The magnitude of the laser power fluctuations depends linearly on the cavity length. The random laser cavity modified with a single highlyreflected (90%) FBG demonstrates significantly better power stability and higher slope efficiency than the same one without an FBG