Fabrication of high-purity polycrystalline mgo

Chemical production and analysis of magnesium oxide - high purity polycrystalline fabricatio

The mechanical behavior of tantalum carbide and magnesium oxide

Mechanical behavior of tantalum carbide and magnesium oxide polycrystalline ceramic

Compatibility Studies of Various Refractory Materials in Contact with Molten Silicon

The production of low cost, efficient solar cells for terrestrial electric power generation involves the manipulation of molten silicon with a present need for noncontaminating, high temperature refractories to be used as containment vessels, ribbon-production dies, and dip-coated substrates. Studies were conducted on the wetting behavior and chemical/physical interactions between molten silicon and various refractory materials

The effect of grain boundaries on mechanical behavior in polycrystalline ceramics

Atomic structure and chemical composition influence on grain boundaries effect on mechanical failure in polycrystalline ceramic

Structure of deformed silicon and implications for low cost solar cells

The microstructure and minority carrier lifetime of silicon were investigated in uniaxially compressed silicon samples. The objective of the investigation was to determine if it is feasible to produce silicon solar cells from sheet formed by high temperature rolling. The initial structure of the silicon samples ranged from single crystal to fine-grained polycrystals. The samples had been deformed at strain rates of 0.1 to 8.5/sec and temperatures of 1270-1380 C with subsequent annealing at 1270-1380 C. The results suggest that high temperature rolling of silicon to produce sheet for cells of high efficiency is not practical

Generation of optimal trajectories for Earth hybrid pole sitters

A pole-sitter orbit is a closed path that is constantly above one of the Earth's poles, by means of continuous low thrust. This work proposes to hybridize solar sail propulsion and solar electric propulsion (SEP) on the same spacecraft, to enable such a pole-sitter orbit. Locally-optimal control laws are found with a semi-analytical inverse method, starting from a trajectory that satisfies the pole-sitter condition in the Sun-Earth circular restricted three-body problem. These solutions are subsequently used as first guess to find optimal orbits, using a direct method based on pseudospectral transcription. The orbital dynamics of both the pure SEP case and the hybrid case are investigated and compared. It is found that the hybrid spacecraft allows savings on propellant mass fraction. Finally, it is shown that for sufficiently long missions, a hybrid pole-sitter, based on mid-term technology, enables a consistent reduction in the launch mass for a given payload, with respect to a pure SEP spacecraft

Realistic Earth escape strategies for solar sailing

With growing interest in solar sailing comes the requirement to provide a basis for future detailed planetary escape mission analysis by drawing together prior work, clarifying and explaining previously anomalies. Previously unexplained seasonal variations in sail escape times from Earth orbit are explained analytically and corroborated within a numerical trajectory model. Blended-sail control algorithms, explicitly independent of time, which providenear-optimal escape trajectories and maintain a safe minimum altitude and which are suitable as a potential autonomous onboard controller, are then presented. These algorithms are investigated from a range of initial conditions and are shown to maintain the optimality previously demonstrated by the use of a single-energy gain control law but without the risk of planetary collision. Finally, it is shown that the minimum sail characteristic acceleration required for escape from a polar orbit without traversing the Earth shadow cone increases exponentially as initial altitude is decreased

Electricity from photovoltaic solar cells: Flat-Plate Solar Array Project final report. Volume IV: High-efficiency solar cells

The Flat-Plate Solar Array (FSA) Project, funded by the U.S. Government and managed by the Jet Propulsion Laboratory, was formed in 1975 to develop the module/array technology needed to attain widespread terrestrial use of photovoltaics by 1985. To accomplish this, the FSA Project established and managed an Industry, University, and Federal Government Team to perform the needed research and development (R&D). The High-Efficiency Solar Cells Task was assigned the objective of understanding and developing high-efficiency solar cell devices that would meet the cost and performance goals of the FSA Project. The need for research dealing with high efficiency devices was considered important because of the role efficiency plays in reducing the price per watt of generated energy. This document is a summary of the R&D efforts conducted during the period 1982 to 1986 to provide understanding and control of energy conversion losses associated with crystalline-silicon solar cells. New levels of conversion efficiency (greater than 20 %) were demonstrated. Major contributions were made both to the understanding and reduction of bulk and surface losses in solar cells. For example, oxides, nitrides, and polysilicon were all shown to be potentially useful surface passivants. Improvements in measurement techniques were made and Auger coefficients and spectral absorption data were obtained for unique types of silicon sheet. New modeling software was developed including a program to optimize a device design based on input characteristics of a cell. Although considerable progress was made in this Task, several elements of research were incomplete at the conclusion of the Project