609 research outputs found
Dilution Zone Mixing
Studies to characterize dilution zone mixing; experiments on the effects of free-stream turbulence on a jet in crossflow; and the development of an interactive computer code for the analysis of the mixing of jets with a confined crossflow are reviewed
Gaseous exhaust emissions from a J-58 engine at simulated supersonic flight conditions
Emissions of total oxides of nitrogen, unburned hydrocarbons, carbon monoxide, and carbon dioxide from a J-58 engine at simulated flight conditions of Mach 2.0, 2.4, and 2.8 at 19.8 km altitude are reported. For each flight condition, measurements were made for four engine power levels from maximum power without afterburning through maximum afterburning. These measurements were made 7 cm downstream of the engine primary nozzle using a single point traversing gas sample probe. Results show that emissions vary with flight speed, engine power level, and with radial position across the exhaust
On the mixing of a row of jets with a confined crossflow
Mean temperature profiles calculated with an interactive microcomputer code which evaluates dilution-zone design alternatives are presented to show the effects of flow and geometric variables on the mixing of a single row of jets injected through sharp-edged orifices into a uniform flow of a different temperature in a constant area duct. In addition, this program is used to calculate profiles for opposed rows of jets with their centerlines in-line, by assuming that the confining effect of an opposite wall is equivalent to that of a plane of symmetry between opposed jets
Dispersion and dilution of jet aircraft exhaust at high-altitude flight conditions
A method is presented for estimating the dispersion and dilution of jet aircraft exhaust from aircraft passage through times on the order of weeks thereafter. In the near wake of the aircraft, the solution is that for round turbulent jets in a parallel flow. More rapid dispersion due to atmospheric effects begins when the scale-dependent eddy viscosity becomes larger than the turbulent jet eddy viscosity. In the far wake region, the solution approaches that for scale-dependent dispersion from a point source moving with the aircraft. Calculations are presented for supersonic aircraft at high altitude flight conditions
Emission calibration of a J-58 afterburning turbojet engine at simulated supersonic stratospheric flight conditions
Emissions of total oxides of nitrogen, unburned hydrocarbons, and carbon monoxide from a J-58 engine at simulated flight conditions of Mach 2.0, 2.4, and 2.8 at 19.8 km altitude are reported. For each flight condition, measurements were made for four engine power levels from maximum power without afterburning through maximum afterburning. These measurements were made 7 cm downstream of the engine primary nozzle using a single point traversing gas sample probe. Results show that emissions vary with flight speed, engine power level, and with radial position across the exhaust
Measurement of exhaust emissions from two J-58 engines at simulated supersonic cruise flight conditions
Emissions of total oxides of nitrogen, unburned hydrocarbons, carbon monoxide, and carbon dioxide from two J-58 afterburning turbojet engines at simulated high-altitude flight conditions are reported. Test conditions included flight speeds from Mach 2 to 3 at altitudes from 16 to 23 km. For each flight condition, exhaust measurements were made for four or five power levels from maximum power without afterburning through maximum afterburning. The data show that exhaust emissions vary with flight speed, altitude, power level, and radial position across the exhaust. Oxides of nitrogen (NOX) emissions decreased with increasing altitude, and increased with increasing flight speed. NOX emission indices with afterburning were less than half the value without afterburning. Carbon monoxide and hydrocarbon emissions increased with increasing altitude, and decreased with increasing flight speed. Emissions of these species were substantially higher with afterburning than without
Perspectives on dilution jet mixing
A microcomputer code which displays 3-D oblique and 2-D plots of the temperature distribution downstream of jets mixing with a confined crossflow has been used to investigate the effects of varying the several independent flow and geometric parameters on the mixing. Temperature profiles calculated with this empirical model are presented to show the effects of orifice size and spacing, momentum flux ratio, density ratio, variable temperature mainstream, flow area convergence, orifice aspect ratio, and opposed and axially staged rows of jets
Airflow distribution control for improved turbine engine performance
Control allows significant diffuser length and weight reduction, reduces combustor exhaust emissions during engine idle, and improves combustor altitude relight capability
Modeling of dilution jet flowfields
The present paper will compare temperature field measurements from selected cases in these investigations with distributions calculated with an empirical model based on assumed vertical profile similarity and superposition and with a 3-D elliptic code using a standard K-E turbulence model. The results will show the capability (or lack thereof) of the models to predict the effects of the principle flow and geometric variables
On modeling dilution jet flowfields
This paper compares temperature field measurements from selected experiments on a single row, and opposed rows, of jets injected into a ducted crossflow with profiles calculated using an empirical model based on assumed vertical profile similarity and superposition, and distributions calculated with a 3-D elliptic code using a standard K-E turbulence model. The empirical model predictions are very good within the range of the generating experiments, and the numerical model resultings, although exhibiting too little mixing, correctly describe the effects of the principal flow and geometric variables
- …