31,659 research outputs found
Parametric finite-element studies on the effect of tool shape in friction stir welding
The success of the Friction Stir Welding (FSW) process, and the weld quality produced, depends significantly on the design of the welding tool. In this paper the effect of variation in various tool geometry parameters on FSW process outcomes, during the plunge stage, were investigated. Specifically the tool shoulder surface angle and the ratio of the shoulder radius to pin radius on tool reaction force, tool torque, heat generation, temperature distribution and size of the weld zone were investigated. The studies were carried out numerically using the finite element method. The welding process used AA2024 aluminium alloy plates with a thickness of 3 mm. It was found that, in plunge stage, the larger the pin radius the higher force and torque the tool experiences and the greater heat generated. It is also found that the shoulder angle has very little effect on energy dissipation as well as little effect on temperature distribution
Orbiter catalytic/noncatalytic heat transfer as evidenced by heating to contaminated surfaces on STS-2 and STS-3
During that portion of Space Shuttle orbiter entry when significant aerodynamic heat transfer occurs, the flow over the vehicle is in chemical nonequilibrium. The parameter which most significantly influences the level of surface heat transfer in such a flow field is the catalytic efficiency of the surface with respect to the recombination of dissociated oxygen atoms. Significant, and instantaneous, changes were observed in the level of heat transfer at several lower surface centerline locations on STS-2 and STS-3. This phenomenon apparently resulted from a sudden change in the surface catalytic efficiency at these locations due to contamination of the surface by metallic oxides. As a result, data obtained from affected measurements cannot be considered as benchmark data with which to attempt to characterize nonequilibrium heat transfer to the orbiter's lower surface centerline
Filler bar heating due to stepped tiles in the shuttle orbiter thermal protection system
An analytical study was performed to investigate the excessive heating in the tile to tile gaps of the Shuttle Orbiter Thermal Protection System due to stepped tiles. The excessive heating was evidence by visible discoloration and charring of the filler bar and strain isolation pad that is used in the attachment of tiles to the aluminum substrate. Two tile locations on the Shuttle orbiter were considered, one on the lower surface of the fuselage and one on the lower surface of the wing. The gap heating analysis involved the calculation of external and internal gas pressures and temperatures, internal mass flow rates, and the transient thermal response of the thermal protection system. The results of the analysis are presented for the fuselage and wing location for several step heights. The results of a study to determine the effectiveness of a half height ceramic fiber gap filler in preventing hot gas flow in the tile gaps are also presented
Inequivalent contact structures on Boothby-Wang 5-manifolds
We consider contact structures on simply-connected 5-manifolds which arise as
circle bundles over simply-connected symplectic 4-manifolds and show that
invariants from contact homology are related to the divisibility of the
canonical class of the symplectic structure. As an application we find new
examples of inequivalent contact structures in the same equivalence class of
almost contact structures with non-zero first Chern class.Comment: 27 pages; to appear in Math. Zeitschrif
Scaling of the Kondo zero bias peak in a hole quantum dot at finite temperatures
We have measured the zero bias peak in differential conductance in a hole
quantum dot. We have scaled the experimental data with applied bias and
compared to real time renormalization group calculations of the differential
conductance as a function of source-drain bias in the limit of zero temperature
and at finite temperatures. The experimental data show deviations from the T=0
calculations at low bias, but are in very good agreement with the finite T
calculations. The Kondo temperature T_K extracted from the data using T=0
calculations, and from the peak width at 2/3 maximum, is significantly higher
than that obtained from finite T calculations.Comment: Accepted to Phys. Rev. B (Rapid
Enzymatic processing of replication and recombination intermediates by the vaccinia virus DNA polymerase
Poxvirus DNA polymerases play a critical role in promoting virus recombination. To test if vaccinia polymerase (E9L) could mediate this effect by catalyzing the post-synaptic processing of recombinant joint molecules, we prepared substrates bearing a nick, a 3â˛-unpaired overhang, a 5Ⲡoverhang, or both 3Ⲡand 5Ⲡoverhangs. The sequence of the 5Ⲡoverhang was also modified to permit or preclude branch migration across the joint site. These substrates were incubated with E9L, and the fate of the primer strand characterized under steady-state reaction conditions. E9L rapidly excises a mispaired 3Ⲡstrand from a DNA duplex, producing a meta-stable nicked molecule that is a substrate for ligase. The reaction was not greatly affected by adding an unpaired 5Ⲡstrand, but since such molecules cannot be processed into nicked intermediates, the 3â˛-ended strand continued to be subjected to exonucleolytic attack. Incorporating homology into the 5Ⲡoverhang prevented this and permitted some strand assimilation, but such substrates also promoted strand-displacement DNA synthesis of a type predicted by the 1981 Moyer and Graves model for poxvirus replication. Single-strand annealing reactions are used by poxviruses to produce recombinant viruses and these data show that virus DNA polymerases can process DNA in such a manner as to both generate single-stranded substrates for such reactions and to facilitate the final processing of the reaction products
Influence of Potamogeton crispus growth on nutrients in the sediment and water of Lake Tangxunhu
An incubation experiment was performed on Potamogeton crispus (P. crispus) using sediment collected from Lake Tangxunhu in the center of China, in order to determine the effects of plant growth on Fe, Si, Cu, Zn, Mn, Mg, P, and Ca concentrations in the sediments and overlying waters. After 3 months of incubation, Ca, Mg, and Si concentrations in the water column were significantly lower, and P and Cu concentrations were significantly higher than in unplanted controls. The effect of P. crispus growth on sediment pore waters and water-extractable elements varied. Concentrations of Ca, Mg, Si, Fe, Cu, and Zn were significantly higher, and P was significantly lower, than in pore waters of the control. Water-extracted concentrations of Fe, Mg, and Si in the sediments were lower, and P was higher, than in the control. Presence of P. crispus generally enhanced concentration gradients of elements between pore waters and overlying waters but not for P. The growth of P. crispus was associated with an increase in water pH and formation of root plaques, resulting in complex effects on the sediment nutritional status
- âŚ