21 research outputs found
A Parameter-Reduced Volterra Model for Dynamic RF Power Amplifier Modeling based on Orthonormal Basis Functions
ABSTRACT: A nonlinear dynamic behavioral model for radio frequency power amplifiers is presented. It uses orthonormal basis functions, Kautz functions, with complex poles that are different for each nonlinear order. It has the same general properties as Volterra models, but the number of parameters is significantly smaller. Using frequency weighting the out-of-band model error can be reduced. Using experimental data it was found that the optimal poles were the same for different input powers and for the different nonlinear orders. The optimal poles were also the same for direct and inverse models, which could be explained theoretically to be a general property of nonlinear systems with negligible linear memory effects. The model can be used as either a direct or inverse model with the same model error for power amplifiers with negligible linear memory effects. VC 2007 Wiley Periodicals
Microwave complex permittivity and anisotropy of conifer wood chips vs moisture content: experiments and modeling
The complex microwave permittivity-including anisotropy- of wood chips of softwood has been measured for different moisture contents in the band 0.75 to 2.5 GHz using an ultra-wide band radio transmission technique. The real and imaginary parts increase monotonically with moisture content. The wood chips are oriented by gravity, which gives anisotropic permittivity. The anisotropy ratio of the real part increases from 1.1 to 1.6 with moisture content from 0 to 120%. The anisotropy ratio of the imaginary part is around 2.5 at all moisture contents. Effective medium models were used to model the permittivity. The Bruggeman, and two versions of the Maxwell Garnett model gave good results at low moisture content (below the fiber saturation point). Above the fiber saturation point only the Bruggeman model gave results in agreement with experiments. The difference in model performance suggests that the free water does not follow the wood chips geometry
Deformation potentials of the E1 transition in Ge, GaAs, InP, ZnSe, and ZnTe from ab initio calculations.
Isotope effects on the electronic critical points of germanium: Ellipsometric investigation of the E
Within the past years the optical excitations of electrons
have been measured for semiconductor samples of different
isotope compositions. The isotope shift observed
have been compared with calculations of the effects of
electron-phonon interaction on the electronic band structure.
While qualitative agreement has been obtained, some
discrepancies remain especially concerning the
E1 and transitions.
We have remeasured the effect of isotope mass on the
E1 and transitions of
germanium with several isotopic compositions.
The results, obtained by means of spectroscopic
ellipsometry, confirm that the real part of the gap
self-energies induced by electron-phonon interaction is
larger than found from band structure calculations,
while the imaginary part agrees with those
calculations, which are based on a pseudopotential band structure and
a bond charge model for the lattice dynamics. Our results agree
with predictions based on the measured temperature
dependence of the gaps. We compare our data for
E1 and with
results for the lowest direct (E0) and indirect
(Eg) gaps. The measured values of
and increase noticeably with increasing
isotope mass. Similar effects have been observed in the
temperature dependence of in
and . A microscopic explanation for this effect
is not available
Wideband Characterization of a Doherty Amplifier Using Behavioral Modeling," presented at ARFTG 67
A Doherty amplifier was investigated using behavioral amplifier modeling techniques. A measurement system for simultaneous wide bandwidth (>100 MHz) and large dynamic range (~70 dBc ACLR) sampled measurements that are needed for the behavioral modeling is presented. Both the measurement system and the performance of the Doherty amplifier are described. The findings are that the well known and widely used parallel Hammerstein model, also denoted the memory polynomial model, is well suitable also for modeling and predistortion of Doherty amplifiers, and that a Doherty amplifier can be designed with only minor memory effects. This is seen in the modeling error, which is reduced by 13 dB, compared with a constant gain, using a memoryless polynomial model and only 6 dB further by adding memory to the model.