A Trigger/Timing Logic Unit for ILC Test-beams

Detector development for the International Linear Collider (ILC) is likely to involve initial beam-tests with a triggered configuration, moving to beam-tests in a triggerless or self-triggered mode. A Trigger/Timing Logic Unit (TLU) is described which allows triggered operation, with option of smooth transition to trigger-less, data-driven mode. The unit has already been sucessfully used for a number of beam-tests

The SoLid anti-neutrino detector's readout system

The SoLid collaboration have developed an intelligent readout system to reduce their 3200 silicon photomultiplier detector's data rate by a factor of 10000 whilst maintaining high efficiency for storing data from anti-neutrino interactions. The system employs an FPGA-level waveform characterisation to trigger on neutron signals. Following a trigger, data from a space time region of interest around the neutron will be read out using the IPbus protocol. In these proceedings the design of the readout system is explained and results showing the performance of a prototype version of the system are presented

Timing and Synchronization of the DUNE Neutrino Detector

The DUNE neutrino experiment far detector has a fiducial mass of 40 kt. The O(1M) readout channels are distributed over the four 10 kt modules and need to be synchronized with respect to each other to a precision of O(10 ns). The entire system needs to be synchronized with respect to GPS time to O(100 ns). The system needs to be reliable, simple and affordable. Clock and synchronization information encoded on the same fibre using a protocol based on duty cycle shift keying (DCSK) with 8b10b encoding to ensure DC-balance. The use of DCSK allows the clock to be recovered directly by PLL based clock generators without needing to use a separate clock and data recovery (CDR) device. Small scale tests show a timing jitter at the endpoint of approximately 10 ps with respect to the timing master.Comment: conferenc

TORCH: A Cherenkov Based Time-of-Flight Detector

TORCH is a novel high-precision time-of-flight detector suitable for large area applications and covering the momentum range up to 10 GeV/c. The concept uses Cherenkov photons produced in a fused silica radiator which are propagated to focussing optics coupled to fast photodetectors. For this purpose, custom MCP-PMTs are being produced in collaboration with industrial partners. The development is divided into three phases. Phase 1 addresses the lifetime requirements for TORCH, Phase 2 will customize the MCP-PMT granularity and Phase 3 will deliver prototypes that meet the TORCH requirements. Phase 1 devices have been successfully delivered and initial tests show stable gain performance for integrated anode current >5 C/cm2 and a single photon time resolution of ≤ 30 ps. Initial simulations indicate the single photon timing resolution of the TORCH detector will be ∼70 ps

Performance of the EUDET-type beam telescopes

Test beam measurements at the test beam facilities of DESY have been conducted to characterise the performance of the EUDET-type beam telescopes originally developed within the EUDET project. The beam telescopes are equipped with six sensor planes using MIMOSA26 monolithic active pixel devices. A programmable Trigger Logic Unit provides trigger logic and time stamp information on particle passage. Both data acquisition framework and offline reconstruction software packages are available. User devices are easily integrable into the data acquisition framework via predefined interfaces. The biased residual distribution is studied as a function of the beam energy, plane spacing and sensor threshold. Its standard deviation at the two centre pixel planes using all six planes for tracking in a 6\,GeV electron/positron-beam is measured to be (2.88\,\pm\,0.08)\,\upmu\meter.Iterative track fits using the formalism of General Broken Lines are performed to estimate the intrinsic resolution of the individual pixel planes. The mean intrinsic resolution over the six sensors used is found to be (3.24\,\pm\,0.09)\,\upmu\meter.With a 5\,GeV electron/positron beam, the track resolution halfway between the two inner pixel planes using an equidistant plane spacing of 20\,mm is estimated to (1.83\,\pm\,0.03)\,\upmu\meter assuming the measured intrinsic resolution. Towards lower beam energies the track resolution deteriorates due to increasing multiple scattering. Threshold studies show an optimal working point of the MIMOSA26 sensors at a sensor threshold of between five and six times their RMS noise. Measurements at different plane spacings are used to calibrate the amount of multiple scattering in the material traversed and allow for corrections to the predicted angular scattering for electron beams

The AIDA-2020 TLU:a flexible trigger logic unit for test beam facilities

The AIDA-2020 Trigger Logic Unit (TLU) has been designed to be a flexible and easily configurable unit to provide trigger and control signals to devices employed during test beams, integrating them with the beam telescope. The most recent iteration of the TLU (v1E) has been re-designed within the AIDA-2020 project to integrate with hardware used in beam facilities. Configuration and communication with the TLU are performed over Ethernet. It can be employed as a stand-alone unit or be deployed as part of the EUDAQ2 data acquisition framework, which allows it to connect to a wide range of LHC readout systems. The TLU can operate with a sustained particle rate of 1 MHz and with instantaneous rates up to 20 MHz. In the current firmware iteration, the unit can time-stamp incoming signals with a resolution of 1.5 ns. The hardware, firmware and software designs of the TLU are freely accessible and benefit from constant inputs and upgrades from experienced users. TLU units have already been deployed successfully in beam lines at CERN and DESY

TORCH: A Cherenkov Based Time-of-Flight Detector

TORCH is a novel high-precision time-of-flight detector suitable for large area applications and covering the momentum range up to 10 GeV/c. The concept uses Cherenkov photons produced in a fused silica radiator which are propagated to focussing optics coupled to fast photodetectors. For this purpose, custom MCP-PMTs are being produced in collaboration with industrial partners. The development is divided into three phases. Phase 1 addresses the lifetime requirements for TORCH, Phase 2 will customize the MCP-PMT granularity and Phase 3 will deliver prototypes that meet the TORCH requirements. Phase 1 devices have been successfully delivered and initial tests show stable gain performance for integrated anode current >5 C/cm2 and a single photon time resolution of ≤ 30 ps. Initial simulations indicate the single photon timing resolution of the TORCH detector will be ∼70 ps

The TORCH time-of-flight detector

AbstractThe TORCH time-of-flight detector is being developed to provide particle identification between 2 and 10GeV/c momentum over a flight distance of 10m. TORCH is designed for large-area coverage, up to 30m2, and has a DIRC-like construction. The goal is to achieve a 15ps time-of-flight resolution per incident particle by combining arrival times from multiple Cherenkov photons produced within quartz radiator plates of 10mm thickness. A four-year R&D programme is underway with an industrial partner (Photek, UK) to produce 53×53mm2 Micro-Channel Plate (MCP) detectors for the TORCH application. The MCP-PMT will provide a timing accuracy of 40ps per photon and it will have a lifetime of up to at least 5Ccm−2 of integrated anode charge by utilizing an Atomic Layer Deposition (ALD) coating. The MCP will be read out using charge division with customised electronics incorporating the NINO chipset. Laboratory results on prototype MCPs are presented. The construction of a prototype TORCH module and its simulated performance are also described

Test-beam and laboratory characterisation of the TORCH prototype detector

The TORCH time-of-flight (TOF) detector is being developed to provide particle identification up to a momentum of 10 GeV/c over a flight distance of 10 m. It has a DIRC-like construction with View the MathML source10mm thick synthetic amorphous fused-silica plates as a Cherenkov radiator. Photons propagate by total internal reflection to the plate periphery where they are focused onto an array of customised position-sensitive micro-channel plate (MCP) detectors. The goal is to achieve a 15 ps time-of-flight resolution per incident particle by combining arrival times from multiple photons. The MCPs have pixels of effective size 0.4 mm×6.6 mm2 in the vertical and horizontal directions, respectively, by incorporating a novel charge-sharing technique to improve the spatial resolution to better than the pitch of the readout anodes. Prototype photon detectors and readout electronics have been tested and calibrated in the laboratory. Preliminary results from testbeam measurements of a prototype TORCH detector are also presented