167,973 research outputs found
Visual and motion simulation techniques
Visual and motion simulation techniques for manned space flight model
Diffusion of trace gases for leak detection in aerospace systems
Diffusion of Freon and helium trace gases for detection of leaks in aerospace system
High pressure Hugoniot measurements using Mach waves
Traditionally, most dynamic shock compression experiments are conducted using a plane one-dimensional wave of uniaxial strain. In this case, the evaluation of the equation of state is simplified due to the geometry, but the amplitude of the induced shock wave is limited by the magnitude of the input load. In an effort to dramatically increase the range of pressures that can be accessed by traditional loading methods, a composite target assembly is examined. The target consists of two concentric cylinders aligned with the axial direction parallel to the loading. The target is designed such that on initial loading, the outer cylinder will have a higher shock velocity than the inner material of interest. Conically converging shocks will be generated at the interface between the two materials due to the impedance mismatch. Upon convergence, an irregular reflection occurs and the conical analog of a Mach reflection develops. The Mach reflection will grow until it reaches a steady state, at which point the wave configuration becomes self similar. The resulting high pressure Hugoniot state can then be measured using velocity interferometry and impedance matching. The technique is demonstrated using a planar mechanical impact generated by a powder gun to study the shock response of copper. Two systems are examined which utilize either a low impedance (6061-T6 aluminum) or a high impedance (molybdenum) outer cylinder. A multipoint VISAR experiment will be presented to validate the technique, and will be compared to numerical simulations. The feasibility of measuring an entire Hugoniot curve using full field velocity interferometry (ORVIS) will also be discussed
A documentation of two- and three-dimensional shock-separated turbulent boundary layers
A shock-related separation of a turbulent boundary layer has been studied and documented. The flow was that of an axisymmetric turbulent boundary layer over a 5.02-cm-diam cylinder that was aligned with the wind tunnel axis. The boundary layer was compressed by a 30 deg half-angle conical flare, with the cone axis inclined at an angle alpha to the cylinder axis. Nominal test conditions were P sub tau equals 1.7 atm and M sub infinity equals 2.85. Measurements were confined to the upper-symmetry, phi equals 0 deg, plane. Data are presented for the cases of alpha equal to 0. 5. and 10 deg and include mean surface pressures, streamwise and normal mean velocities, kinematic turbulent stresses and kinetic energies, as well as reverse-flow intermittencies. All data are given in tabular form; pressures, streamwise velocities, turbulent shear stresses, and kinetic energies are also presented graphically
Characterizations of four specimens processed as a part of the M553 sphere forming experiment performed during the Skylab 1 and 2 flight
Four specimens identified as SL-1.3, SL-1.8, SL-1.9 and SL-2.5 were submitted for metallurgical characterization. These specimens had been processed in the M512 Facility as a part of the M553 Sphere Forming Experiment performed during the Skylab 1/2 flight. Three of these specimens, SL-1.3, SL-1.8, and SL-2.5 were designed to be melted completely by the electron beam and detach themselves from their support posts and resolidify while floating free in the near zero gravity and vacuum environment of space. Specimens SL-1.3 and SL-1.8 were completely melted, but it is believed they did not leave their posts before solidifying. Specimen SL-2.5 was only partially melted. Specimen SL-1.9 was to be completely melted and retained on a large sting which was accomplished as planned. The nominal composition of the four specimens was: (1) SL-1.3 - Ni 12% Sn; (2) SL-1.8 - Ni 30% Cu; (3) SL-1.9 - Pure Ni; and (4) SL-2.5 - Pure Ni. These four specimens have been examined according to the Phase B Characterization Plan. The results are discussed and compared with similar characterization analyses run on ground base specimens
Polarimetric variations of binary stars. II. Numerical simulations for circular and eccentric binaries in Mie scattering envelopes
We present numerical simulations of the periodic polarimetric variations
produced by a binary star placed at the center of an empty spherical cavity
inside a circumbinary ellipsoidal and optically thin envelope made of dust
grains. Mie single-scattering is considered along with pre- and post-scattering
extinction factors which produce a time-varying optical depth and affect the
morphology of the periodic variations. We are interested in the effects that
various parameters will have on the average polarization, the amplitude of the
polarimetric variations, and the morphology of the variability. We show that
the absolute amplitudes of the variations are smaller for Mie scattering than
for Thomson scattering. Among the four grain types that we have studied, the
highest polarizations are produced by grains with sizes in the range 0.1-0.2
micron. In general, the variations are seen twice per orbit. In some cases,
because spherical dust grains have an asymmetric scattering function, the
polarimetric curves produced also show variations seen once per orbit.
Circumstellar disks produce polarimetric variations of greater amplitude than
circumbinary envelopes.
Another goal of these simulations is to see if the 1978 BME (Brown, McLean, &
Emslie, ApJ, 68, 415) formalism, which uses a Fourier analysis of the
polarimetric variations to find the orbital inclination for Thomson-scattering
envelopes, can still be used for Mie scattering. We find that this is the case,
if the amplitude of the variations is sufficient and the true inclinations is
i_true > 45 deg. For eccentric orbits, the first-order coefficients of the
Fourier fit, instead of second-order ones, can be used to find almost all
inclinations.Comment: 23 pages, 5 figures, to be published in Astronomical Journa
Application of calibration masks to TV vidicon tube
Photographic application method devised for overlaying test pattern masks on TV camera vidicon tubes prints the mask within 0.0076 cm of the vertical and horizontal center lines of the tube face. Entire process, including mask fabrication and alignment procedure, requires less than 10 minutes
Health and safety: Preliminary comparative assessment of the Satellite Power System (SPS) and other energy alternatives
Data readily available from the literature were used to make an initial comparison of the health and safety risks of a fission power system with fuel reprocessing; a combined-cycle coal power system with a low-Btu gasifier and open-cycle gas turbine; a central-station, terrestrial, solar photovoltaic power system; the satellite power system; and a first-generation fusion system. The assessment approach consists of the identification of health and safety issues in each phase of the energy cycle from raw material extraction through electrical generation, waste disposal, and system deactivation; quantitative or qualitative evaluation of impact severity; and the rating of each issue with regard to known or potential impact level and level of uncertainty
Boundary States and Black Hole Entropy
Black hole entropy is derived from a sum over boundary states. The boundary
states are labeled by energy and momentum surface densities, and parametrized
by the boundary metric. The sum over state labels is expressed as a functional
integral with measure determined by the density of states. The sum over metrics
is expressed as a functional integral with measure determined by the universal
expression for the inverse temperature gradient at the horizon. The analysis
applies to any stationary, nonextreme black hole in any theory of gravitational
and matter fields.Comment: 4 pages, Revte
- …