16,655 research outputs found
Aerodynamic characteristics of several airfoils of low aspect ratio
This paper presents the results of wind-tunnel tests of several airfoils of low aspect ratio. The airfoils included three circular Clark Y airfoils with different amounts of dihedral, two Clark Y airfoils with slots in their portions, and three flat-plate airfoils. Lift, drag, and pitching-moment characteristics of the slotted airfoils with slots open and closed; pitching moment characteristics of one of the slotted airfoils with slots open and closed; and lift characteristics of the flat-plate airfoils are included. The results reveal a definite improvement of lift, drag, and pitching-moment characteristics with increase in dihedral of the circular Clark Y wing. Lift characteristics near the stall were found to depend markedly on the shape of the extreme tip but were not greatly affected by slots through the after portion of the airfoils. Changes in plan form of the flat-plate airfoils gave erroneous indications of the effect to be expected from changes in plan form of an airfoil of Clark Y section. The minimum drag characteristics of the circular Clark Y airfoils were found to be substantially the same as for a Clark Y airfoil of conventional aspect ratio
Nickel-cadmium Battery Cell Reversal from Resistive Network Effects
During the individual cell short-down procedures often used for storing or reconditioning nickel-cadmium (Ni-Cd) batteries, it is possible for significant reversal of the lowest capacity cells to occur. The reversal is caused by the finite resistance of the common current-carrying leads in the resistive network that is generally used during short-down. A model is developed to evaluate the extent of such a reversal in any specific battery, and the model is verified by means of data from the short-down of a f-cell, 3.5-Ah battery. Computer simulations of short-down on a variety of battery configurations indicate the desirability of controlling capacity imbalances arising from cell configuration and battery management, limiting variability in the short-down resistors, minimizing lead resistances, and optimizing lead configurations
Mechanisms for capacity fading in the NiH2 cell and its effects on cycle life
During recent years there have been a number of instances where the capacity of nickel hydrogen battery cells has proven to be unstable during storage. The capacity losses seen after periods of cell or battery storage have typically varied from only a small amount of fading, up to about 30 percent of the total cell capacity. Detailed studies into the root causes for such fading have been carried out in a number of instances. This report provides an overview of the different mechanisms that have been found to be responsible for such capacity fading in nickel hydrogen cells, and summarizes the presently available data on how each responsible mechanism affects ultimate cell cycle life
Passive dual spin misalignment compensators
A combination dual-spin gyroscopically stabilized device is described having a spinning rotor and a non-spinning platform. Two substantially lossless mechanical resonators, resonant at the spin frequency, are orthogonally positioned on the platform for compensation for the disturbing torque acting on the platform due to rotor misalignment
The Aerodynamic Forces and Moments on a Spinning Model of the F4B-2 Airplane as Measured by the Spinning Balance
The aerodynamic forces and moments on a 1/12-scale model of the F4B-2 airplane were measured with the spinning balance in nine spinning attitudes with three sets of tail surfaces, namely, F4B-2 surfaces; F4B-4 fin and rudder with rectangular stabilizer; and with all tail surfaces removed. In one of these attitudes measurements were made to determine the effect upon the forces and moments of independent and of simultaneous displacement of the rudder and elevator for two of the sets of tail surfaces. Additional measurements were made for a comparison of model and full-scale data for six attitudes that were determined from flight tests with various control settings. The characteristics were found to vary in the usual manner with angle of attack and sideslip. The F4B-2 surfaces were quite ineffective as a source of yawing moments. The F4B-4 fin and F4B-2 stabilizer gave a greater damping yawing moment when controls were against the spin than did the F4B-2 surfaces but otherwise there was little difference. Substitution of a rectangular stabilizer for the F4B-2 stabilizer made no appreciable difference in the coefficient. Further comparisons with other airplane types are necessary before final conclusions can be drawn as to the relations between model and full-scale spin measurements
Evaluation of a metal shear web selectively reinforced with filamentary composites for space shuttle application. Phase 1 summary report: Shear web design development
An advanced composite shear web design concept was developed for the Space Shuttle orbiter main engine thrust beam structure. Various web concepts were synthesized by a computer-aided adaptive random search procedure. A practical concept is identified having a titanium-clad + or - 45 deg boron/epoxy web plate with vertical boron/epoxy reinforced aluminum stiffeners. The boron-epoxy laminate contributes to the strength and stiffness efficiency of the basic web section. The titanium-cladding functions to protect the polymeric laminate parts from damaging environments and is chem-milled to provide reinforcement in selected areas. Detailed design drawings are presented for both boron/epoxy reinforced and all-metal shear webs. The weight saving offered is 24% relative to all-metal construction at an attractive cost per pound of weight saved, based on the detailed designs. Small scale element tests substantiate the boron/epoxy reinforced design details in critical areas. The results show that the titanium-cladding reliably reinforces the web laminate in critical edge load transfer and stiffener fastener hole areas
An experimental investigation of high amplitude panel flutter
Aluminum panel flutter tests at supersonic Mach number
A method for predicting the panel flutter fatigue life of Saturn 5 panels
Development of method for predicting fatigue life of panels under flutter conditions with application to Saturn 5 launch vehicle structure
Computer program conducts facilities utilization and occupancy survey
Computer program identifies the uses of all facilities and provides information on the net area in each room as well as the number and classification of people occupying them. The system also provides a means to indicate unsatisfactory work areas and may be able to be updated each month
- …