324 research outputs found
Three-Dimensional Finite Element Study on Stress Generation in Synchrotron X-Ray Tomography Reconstructed Nickel-Manganese-Cobalt Based Half Cell
In this study, the stress generation caused by phase transitions and lithium intercalation of nickel-manganese-cobalt (NMC) based half cell with realistic 3D microstructures has been studied using finite element method. The electrochemical properties and discharged curves under various C rates are studied. The potential drops significantly with the increase of C rates. During the discharge process, for particles isolated from the conductive channels, several particles with no lithium ion intercalation are observed. For particles in the electrochemical network, the lithium ion concentration increases during the discharge process. The stress generation inside NMC particles is calculated coupled with lithium diffusion and phase transitions. The results show the stresses near the concave and convex regions are the highest. The neck regions of the connected particles can break and form several isolated particles. If the isolated particles are not connected with the electrically conductive materials such as carbon and binder, the capacity loses in battery. For isolated particles in the conductive channel, cracks are more likely to form on the surface. Moreover, stresses inside the particles increase dramatically when considering phase transitions. The phase transitions introduce an abrupt volume change and generate the strain mismatch, causing the stresses increase
A 550,000-year record of East Asian monsoon rainfall from Be-10 in loess
Cosmogenic Be-10 flux from the atmosphere is a proxy for rainfall. Using this proxy, we derived a 550,000-year-long record of East Asian summer monsoon (EASM) rainfall from Chinese loess. This record is forced at orbital precession frequencies, with higher rainfall observed during Northern Hemisphere summer insolation maxima, although this response is damped during cold interstadials. The Be-10 monsoon rainfall proxy is also highly correlated with global ice-volume variations, which differs from Chinese cave delta O-18, which is only weakly correlated. We argue that both EASM intensity and Chinese cave delta O-18 are not governed by high-northern-latitude insolation, as suggested by others, but rather by low-latitude interhemispheric insolation gradients, which may also strongly influence global ice volume via monsoon dynamics
Microporous metallic scaffolds supported liquid infused icephobic construction.
Ice accretion on component surfaces often causes severe impacts or accidents. Liquid-infused surfaces (LIS) have drawn much attention as icephobic materials for ice mitigation in recent years due to their outstanding icephobicity. However, the durability of LIS constructions remains a big challenge, including mechanical vulnerability and rapid depletion of lubricants. The practical applications of LIS materials are significantly restrained, and the full potential of LIS for ice prevention has yet to be demonstrated. A universal approach was proposed to introduce microporous metallic scaffolds in the LIS construction to increase the applicability and durability, and to prompt the potential of LIS for ice mitigation. Microporous Ni scaffolds were chosen to integrate with polydimethylsiloxane modified by silicone oil addition. The new LIS construction demonstrated significantly improved durability in icing/de-icing cyclic test, and it also offered a solution for the rapid oil depletion by restraining the deformation of the matrix material. Low ice adhesion strength could be maintained via a micro-crack initiation mechanism. The results indicated that the multi-phase LIS construction consisting of microporous Ni scaffolds effectively addressed the shackles of the icephobicity deterioration of LIS materials, confirming a new design strategy for the R&D of icephobic surfaces
Boron-doped rutile TiO2/ anatase TiO2/ ZrTiO4 ternary heterojunction photocatalyst with optimized phase interface and band structure
To improve the photocatalytic performance of TiO2-based heterostructures, Z-scheme/ā
”-type rutile TiO2 (R)/anatase TiO2 (A)/ZrTiO4 ternary heterojunction photocatalyst was designed and prepared via a facile one-step calcining strategy. Phase interface and band structure of the materials were controlled and optimized by regulating RāTiO2/AāTiO2 mass ratio in the TiO2 (A, R)/ZrTiO4 structures using boron doping. The highest photocatalytic performance and excellent catalytic stability of Rhodamine B removal was observed from the heterojunction with a low RāTiO2/AāTiO2 mass ratio of 0.066, even after five testing cycles, accompanying with low photoluminescence intensity and electrochemical impedance, high photocurrent and charge carrier density (5.12 Ć 1022 cmā3), and a positive shift of valence band position (from +2.06 to + 2.16 eV). The increased photodegradation behaviour was due to the remarkably enhanced separation efficiency and improved redox ability of the photo-induced charge carriers as a result of the high content of oxygen vacancies and the formed anatase TiO2/rutile TiO2 Z-scheme heterojunction
Metallic skeleton promoted two-phase durable icephobic layers
HypothesisThe accretion of ice on component surfaces often causes severe impacts or accidents in modern industries. Applying icephobic surface is considered as an effective solution to minimise the hazards. However, the durability of the current icephobic surface and coatings for long-term service remains a great challenge. Therefore, it is indeed to develop new durable material structures with great icephobic performance.ExperimentsA new design concept of combining robust porous metallic skeletons and icephobic filling was proposed. Nickel/polydimethylsiloxane (PDMS) two-phase layer was prepared using porous Ni foam skeletons impregnated with PDMS as filling material by a two-step method.FindingsGood icephobicity and mechanical durability have been verified. Under external force, micro-cracks could easily initiate at the ice/solid interface due to the small surface cavities and the difference of local elastic modulus between the ice and PDMS, which would promote the ice fracture and thus lead to low ice adhesion strength. The surface morphology and icephobicity almost remain unchanged after water-sand erosion, showing greatly improved mechanical durability. By combining the advantages of the mechanical durability of porous Ni skeleton and the icephobicity of PDMS matrix, the Ni foam/PDMS two-phase layer demonstrates great potentials for ice protection with long-term service time
In-situ synthesis of ultra-fine ZrB2āZrCāSiC nanopowders by sol-gel method
Ā© 2019 Elsevier Ltd and Techna Group S.r.l. ZrB2āZrCāSiC nanopowders with uniform phase distribution were prepared from cost-effective ZrOCl2Ā·8H2O by a simple sol-gel method. The synthesis route, ceramization mechanism and morphology evolution of the nanopowders were investigated. ZrB2āZrCāSiC ceramic precursor can be successfully obtained through hydrolysis and condensation reactions between the raw materials. Pyrolysis of the precursor was completed at 650 Ā°C, and it produced ZrO2, SiO2, B2O3 and amorphous carbon with a yield of 39% at 1300 Ā°C. By heat-treated at 1500 Ā°C for 2 h, highly crystallized ZrB2āZrCāSiC ceramics with narrow size distribution were obtained. With the holding time of 2 h, both the crystal size and the particle size can be refined. Further prolonging the holding time can lead to serious particles coarsening. Studies on the microstructure evolution of the generated carbon during the ceramic conversion demonstrates the negative effect of the ceramic formation on the structure order improvement of the carbon, due to the large amount of defects generated in it by the boro/carbothermal reduction reactions
- ā¦