Large-area wet-chemical deposition of nanoporous tungstic silica coatings

We report on a facile procedure for synthesis of nanoporous coatings of tungstic silica through wet-chemical deposition and post-treatment of tungsten-doped potassium silicate solutions. The process relies on an aqueous washing and ion exchange step where dispersed potassium salt deposits are removed from a 150 nm silicate gel layer. Through an adjustment of the pH value of the washing agent within the solubility regime of a tungstic salt precursor, the tungsten content of the remaining nanostructured coating can be controlled. We propose this route as a universal approach for the deposition of large-area coatings of nanoporous silica with the potential for incorporating a broad variety of other dopant species. As for the present case, we observe, on the one hand, antireflective properties which enable the reduction of reflection losses from float glass by up to 3.7 percent points. On the other hand, the incorporation of nanoscale tungstic precipitates provides a lever for tailoring the coating hydrophilicity and, eventually, also surface acidity. This may provide a future route for combining optical performance with anti-fouling functionality

Serrated flow of CuZr-based bulk metallic glasses probed by nanoindentation: Role of the activation barrier, size and distribution of shear transformation zones

We report on the effect of Al and Co alloying in vitreous Cu50Zr50 on local deformation and serrated flow as a model for relating the size and localization of shear transformation zones (STZ) to Poisson ratio and strain-rate sensitivity of metallic glasses. Alloying with Al results in significant variations in mechanical performance, in particular, in Young's modulus, hardness and strain-rate sensitivity. Increasing strain-rate sensitivity with increasing degree of alloying indicates a reduced tendency for shear localization. In parallel, a gradual transition from inhomogeneous to homogeneous plastic flow is observed. Using a statistical analysis of the shear stress associated with the initiation of the first pop-in in the load-displacement curve during spherical indentation, the activation volume for plastic flow at the onset of yielding is reported. This analysis is employed for experimental evaluation of the compositional dependence of activation barrier, size and distribution of STZs. It is demonstrated that the STZ size does not change significantly upon Al alloying and encompasses a local volume of around 22–24 atoms. However, the barrier energy density for the initiation of a single STZ progressively increases. The broader distribution of STZs impedes their accumulation into larger-size flow units, leading to a lower number and reduced size of serrations in the load-displacement curve. On the contrary, lower barrier energy densities enable a larger quantity of STZs to be activated simultaneously. These STZs can easily percolate into large flow units, promoting plastic flow through their interaction. We employ Poisson's ratio as an indicator for plasticity to shown that this interpretation can be transferred to other types of metallic glasses. That is, larger flow units were found for metallic glasses with higher Poisson ratio and more pronounced plasticity, while the flow units in alloys with very low Poisson ratio and high brittleness are significantly reduced in size and more homogeneously distributed throughout the material

Diffusion and interface effects during preparation of all-solid microstructured fibers

All-solid microstructured optical fibers (MOF) allow the realization of very flexible optical waveguide designs. They are prepared by stacking of doped silica rods or canes in complex arrangements. Typical dopants in silica matrices are germanium and phosphorus to increase the refractive index (RI), or boron and fluorine to decrease the RI. However, the direct interface contact of stacking elements often causes interrelated chemical reactions or evaporation during thermal processing. The obtained fiber structures after the final drawing step thus tend to deviate from the targeted structure risking degrading their favored optical functionality. Dopant profiles and design parameters(e.g., the RI homogeneity of the cladding) are controlled by the combination of diffusion and equilibrium conditions of evaporation reactions. We show simulation results of diffusion and thermal dissociation in germanium and fluorine doped silica rod arrangements according to the monitored geometrical disturbances in stretched canes or drawn fibers. The paper indicates geometrical limits of dopant structures in sub-μm-level depending on the dopant concentration and the thermal conditions during the drawing process. The presented results thus enable an optimized planning of the preform parameters avoiding unwanted alterations in dopant concentration profiles or in design parameters encountered during the drawing process

Influence of process parameters on the incorporation of phosphorus into silica soot material during MCVD process

The incorporation of phosphorus into silica soot material strongly changes during the multistep preparation process of the MCVD technology in combination with solution doping for Al and rare earths. We report on the influence of various process parameters on the phosphorus concentration, the bond types of phosphorus atoms and the relative density of the soot material. By optimization of the process the phosphorus concentration of the presintered soot could be increased by around 10% in comparison to the conventional treatment. The understanding of the interdependencies allows an improvement of the preparation process of phosphorus co-doped RE doped silica laser fibers with MCVD technology

Impact of rare earth doping on the luminescence of lanthanum aluminum silicate glasses for radiation sensing

Large core soft glass fibers have been demonstrated to be promising candidates as intrinsic fiber sensors for radiation detection and dosimetry applications. Doping with rare earth ions enhanced their radiation sensitivity. SiO2-Al2O3-La2O3 (SAL) glasses offer easy fabrication of large core fibers with high rare earth concentration and higher mechanical strength than soft glasses. This paper evaluates the suitability of the SAL glass type for radiation dosimetry based on optically stimulated luminescence (OSL) via a comprehensive investigation of the spectroscopic and dosimetric properties of undoped and differently rare earth doped bulk SAL glass samples. Due to the low intensity of the rare earth luminescence peaks in the 250–400 nm OSL detection range, the OSL response for all the SAL glasses is not caused by the rare earth ions but by radiation-induced defects that act as intrinsic centers for the recombination of electrons and holes produced by the ionizing radiation, trapped in fabrication induced defect centers, and then released via stimulation with 470 nm light. The rare earth ions interfere with these processes involving intrinsic centers. This dosimetric behavior of highly rare earth doped SAL glasses suggests that enhancement of OSL response requires lower rare earth concentrations and/or longer wavelength OSL detection range.Ruth E. Shaw, Christopher A. G. Kalnins, Carly A. Whittaker, Jillian E. Moffatt, Georgios Tsiminis, Elizaveta Klantsataya, David Ottaway, Nigel A. Spooner, Doris Litzkendorf, Anne Matthes, Anka Schwuchow, Katrin Wondraczek, and Heike Ebendorff-Heideprie

Optical breathing of nano-porous antireflective coatings through adsorption and desorption of water

We report on the direct consequences of reversible water adsorption on the optical performance of silica-based nanoporous antireflective (AR) coatings as they are applied on glass in photovoltaic and solar thermal energy conversion systems. In situ UV-VIS transmission spectroscopy and path length measurements through high-resolution interferometric microscopy were conducted on model films during exposure to different levels of humidity and temperature. We show that water adsorption in the pores of the film results in a notable increase of the effective refractive index of the coating. As a consequence, the AR effect is strongly reduced. The temperature regime in which the major part of the water can be driven-out rapidly lies in the range of 55°C and 135°C. Such thermal desorption was found to increase the overall transmission of a coated glass by ∼ 1%-point. As the activation energy of isothermal desorption, we find a value of about 18 kJ/mol. Within the experimental range of our data, the sorption and desorption process is fully reversible, resulting in optical breathing of the film. Nanoporous AR films with closed pore structure or high hydrophobicity may be of advantage for maintaining AR performance under air exposure

Large-area wet-chemical deposition of nanoporous tungstic silica coatings

We report on a facile procedure for synthesis of nanoporous coatings of tungstic silica through wet-chemical deposition and post-treatment of tungsten-doped potassium silicate solutions. The process relies on an aqueous washing and ion exchange step where dispersed potassium salt deposits are removed from a 150 nm silicate gel layer. Through an adjustment of the pH value of the washing agent within the solubility regime of a tungstic salt precursor, the tungsten content of the remaining nanostructured coating can be controlled. We propose this route as a universal approach for the deposition of large-area coatings of nanoporous silica with the potential for incorporating a broad variety of other dopant species. As for the present case, we observe, on the one hand, antireflective properties which enable the reduction of reflection losses from float glass by up to 3.7 percent points. On the other hand, the incorporation of nanoscale tungstic precipitates provides a lever for tailoring the coating hydrophilicity and, eventually, also surface acidity. This may provide a future route for combining optical performance with anti-fouling functionality

Large-area wet-chemical deposition of nanoporous tungstic silica coatings

\u3cp\u3eWe report on a facile procedure for synthesis of nanoporous coatings of tungstic silica through wet-chemical deposition and post-treatment of tungsten-doped potassium silicate solutions. The process relies on an aqueous washing and ion exchange step where dispersed potassium salt deposits are removed from a 150 nm silicate gel layer. Through an adjustment of the pH value of the washing agent within the solubility regime of a tungstic salt precursor, the tungsten content of the remaining nanostructured coating can be controlled. We propose this route as a universal approach for the deposition of large-area coatings of nanoporous silica with the potential for incorporating a broad variety of other dopant species. As for the present case, we observe, on the one hand, antireflective properties which enable the reduction of reflection losses from float glass by up to 3.7 percent points. On the other hand, the incorporation of nanoscale tungstic precipitates provides a lever for tailoring the coating hydrophilicity and, eventually, also surface acidity. This may provide a future route for combining optical performance with anti-fouling functionality.\u3c/p\u3

Magnetic and magneto-optical quenching in (Mn[2+], Sr[2+]) metaphosphate glasses

Transition metal ions such as Mn[2+], Fe[2+], or Co[2+] provide an interesting alternative to rare earth dopants in optically active glasses. In terms of their magneto-optical properties, they are not yet very well exploited. Here, we report on the effect of Mn[2+] on Faraday rotation in a metaphosphate glass matrix along the join Mn{x}Sr{1-x}(PO{3}){2} with x = 0...1. Mn[2+] shows small optical extinction in the visible spectral range and, compared to other transition metal ions, a high effective magnetic moment. At high Mn- levels, however, the magneto-optical activity of Mn[2+] is strongly quenched due to ionic clustering. The magnetic properties of the heavily Mn[2+]-loaded phosphate matrix are dominated by a superexchange interaction in the Mn[2+]-O-Mn[2+] bridge with antiparallel spin alignment between Mn[2+] and O[2-] species. The apparent paramagnetic potential of Mn[2+] species can therefore not be exploited at room temperature