Synchrotron x-ray measurement and finite element analysis of residual strain in TIG welded aluminium alloy 2024

Residual strains have been measured in a tungsten inert gas (TIG) butt-welded 2024 aluminum alloy plate using synchrotron X-ray diffraction. Novel two-dimensional strain maps spanning the entire plate reveal steep gradients in residual stress and provide detailed validation data for finite element (FE) analysis. Two variants of a FE model have been used to predict the residual strain distributions, incorporating different levels of plate constraint. The model uses decoupled thermal and elastic- plastic mechanical analyses and successfully predicts the longitudinal and transverse residual strain field over the entire weld. For butt weld geometries, the degree of transverse constraint is shown to be a significant boundary condition, compared to simpler bead-on-plate analyses. The importance of transverse residual strains for detailed model validation is highlighted, together with the need for care in selecting the location for line scans. The residual stress is largest in the heat-affected zone (HAZ), being equal to the local postweld yield stress, though the strength increases subsequently by natural aging. In addition, a halving of the diffraction line width has been observed local to the weld, and this correlates with the microstructural changes in the region

Evolution of damage during the fatigue of 3D woven glass-fibre reinforced composites subjected to tension-tension loading observed by time-lapse X-ray tomography

The development of fatigue damage in a glass fibre modified layer-to-layer three dimensional (3D) woven composite has been followed by time-lapse X-ray computed tomography (CT). The damage was found to be distributed regularly throughout the composite according to the repeating unit, even at large fractions of the total life. This suggests that the through-thickness constraint provides a high level of stress redistribution and damage tolerance. The different types of damage have been segmented, allowing a quantitative analysis of damage evolution as a function of the number of fatigue cycles. Transverse cracks were found to initiate within the weft after just 0.1% of life, followed soon after (by 1% of life) by longitudinal debonding cracks. The number and extent of these multiplied steadily over the fatigue life, whereas the spacing of transverse cracks along with weft/binder debonding saturated at 60% of life and damage in the resin pockets occurred only just before final failure

Exploring microstructural changes associated with oxidation in Ni-YSZ SOFC electrodes using high resolution X-ray computed tomography

State of the art solid oxide fuel cell (SOFC) anodes are typically Ni based, one of the primary drawbacks of these electrodes is their significant dimensional change upon oxidation. As commercial SOFCs may typically be expected to undergo numerous redox cycles in their operating lifetime, it is important to understand the associated microstructural degradation process. Here we present a methodology for the use of synchrotron based X-ray nano-computed tomography to explore the step-wise oxidation of the Ni phase in a Ni–YSZ composite material. This non-destructive technique demonstrates the potential to track microstructural evolution on a grain-by-grain basis in three dimensions

Ribosomal S6K1 in POMC and AgRP Neurons Regulates Glucose Homeostasis but Not Feeding Behavior in Mice.

SummaryHypothalamic ribosomal S6K1 has been suggested as a point of convergence for hormonal and nutrient signals in the regulation of feeding behavior, bodyweight, and glucose metabolism. However, the long-term effects of manipulating hypothalamic S6K1 signaling on energy homeostasis and the cellular mechanisms underlying these roles are unclear. We therefore inactivated S6K1 in pro-opiomelanocortin (POMC) and agouti-related protein (AgRP) neurons, key regulators of energy homeostasis, but in contrast to the current view, we found no evidence that S6K1 regulates food intake and bodyweight. In contrast, S6K1 signaling in POMC neurons regulated hepatic glucose production and peripheral lipid metabolism and modulated neuronal excitability. S6K1 signaling in AgRP neurons regulated skeletal muscle insulin sensitivity and was required for glucose sensing by these neurons. Our findings suggest that S6K1 signaling is not a general integrator of energy homeostasis in the mediobasal hypothalamus but has distinct roles in the regulation of glucose homeostasis by POMC and AgRP neurons

Evaluation of Errors Associated with Cutting-Induced Plasticity in Residual Stress Measurements Using the Contour Method

Cutting-induced plasticity can lead to elevated uncertainties in residual stress measurements made by the contour method. In this study plasticity-induced stress errors are numerically evaluated for a benchmark edge-welded beam to understand the underlying mechanism. Welding and cutting are sequentially simulated by finite element models which have been validated by previous experimental results. It is found that a cutting direction normal to the symmetry plane of the residual stress distribution can lead to a substantially asymmetrical back-calculated stress distribution, owing to cutting-induced plasticity. In general, the stresses at sample edges are most susceptible to error, particularly when the sample is restrained during cutting. Inadequate clamping (far from the plane of cut) can lead to highly concentrated plastic deformation in local regions, and consequently the back-calculated stresses have exceptionally high values and gradients at these locations. Furthermore, the overall stress distribution is skewed towards the end-of-cut side. Adequate clamping (close to the plane of cut) minimises errors in back-calculated stress which becomes insensitive to the cutting direction. For minimal constraint (i.e. solely preventing rigid body motion), the plastic deformation is relatively smoothly distributed, and an optimal cutting direction (i.e. cutting from the base material towards the weld region in a direction that falls within the residual stress symmetry plane) is identified by evaluating the magnitude of stress errors. These findings suggest that cutting process information is important for the evaluation of potential plasticity-induced errors in contour method results, and that the cutting direction and clamping strategy can be optimised with an understanding of their effects on plasticity and hence the back-calculated stresses

Anisotropic crack propagation and deformation in dentin observed by four-dimensional X-ray nano-computed tomography

Understanding the cracking behaviour of biological composite materials is of practical importance. This paper presents the first study to track the interplay between crack initiation, microfracture and plastic deformation in three dimensions (3D) as a function of tubule and collagen fibril arrangement in elephant dentin using in situ X-ray nano-computed tomography (nano-CT). A nano-indenter with a conical tip has been used to incrementally indent three test-pieces oriented at 0°, 45° and 70° to the long axis of the tubules (i.e. radial to the tusk). For the 0° sample two significant cracks formed, one of which linked up with microcracks in the axial-radial plane of the tusk originating from the tubules and the other one occurred as a consequence of shear deformation at the tubules. The 70° test-piece was able to bear the greatest loads despite many small cracks forming around the indenter. These were diverted by the microstructure and did not propagate significantly. The 45° test-piece showed intermediate behaviour. In all cases strains obtained by digital volume correlation were well in excess of the yield strain (0.9%), indeed some plastic deformation could even be seen through bending of the tubules. The hoop strains around the conical indenter were anisotropic with the smallest strains correlating with the primary collagen orientation (axial to the tusk) and the largest strains aligned with the hoop direction of the tusk

Versatile regularisation toolkit for iterative image reconstruction with proximal splitting algorithms

Ill-posed image recovery requires regularisation to ensure stability. The presented open-source regularisation toolkit consists of state-of-the-art variational algorithms which can be embedded in a plug-and-play fashion into the general framework of proximal splitting methods. The packaged regularisers aim to satisfy various prior expectations of the investigated objects, e.g., their structural characteristics, smooth or non-smooth surface morphology. The flexibility of the toolkit helps with the design of more advanced model-based iterative reconstruction methods for different imaging modalities while operating with simpler building blocks. The toolkit is written for CPU and GPU architectures and wrapped for Python/MATLAB. We demonstrate the functionality of the toolkit in application to Positron Emission Tomography (PET) and X-ray synchrotron computed tomography (CT)

Annual changes in aerobic fitness are biased between normative equations in children and adolescents with cystic fibrosis

This is the author accepted manuscript. The final version is available from Elsevier via the DOI in this recordPaper P298 presented at the the 43rd European Cystic Fibrosis Digital Conference, 24 - 25 September 202