Investigation of Tantalum Wet Slug Capacitor Failures in the Apollo Telescope Mount Charger Battery Regulator Modules

This investigation describes the capacitor failures and to identify the cause of the failure mechanism. Early failures were thought to have happened because of age and/or abuse since the failed capacitors were dated 1967. It is shown that all 1967 capacitors were replaced with 1972 capacitors

Forest land management by satellite: LANDSAT-derived information as input to a forest inventory system

The author has identified the following significant results. Analysis of LANDSAT temporal data, specifically the digitally merged winter and summer scenes, provided the best overall classification results. Comparison of temporal classification results with available ground truth reveal a 94% agreement in the delineation of hardwood categories, a 96% agreement for the combined pine category, and a greater than 50% agreement for each individual pine subcategory. For nearly 1000 acres, compared clearcut acreage estimated with LANDSAT digital data differed from company inventory records by only 3%. Through analysis of summer data, pine stands were successfully classified into subcategories based upon the extent of crown closure. Maximum spectral separability of hardwood and pine stands was obtained from the analysis of winter data

Rotor redesign for a highly loaded 1800 ft/sec tip speed fan. 3: Laser Doppler velocimeter report

Laser Doppler velocimeter (LDV) techniques were employed for testing a highly loaded, 550 m/sec (1800 ft/sec) tip speed, test fan stage, the objective to provide detailed mapping of the upstream, intrablade, and downstream flowfields of the rotor. Intrablade LDV measurements of velocity and flow angle were obtained along four streamlines passing through the leading edge at 45%, 69%, 85%, and 95% span measured from hub to tip, at 100% of design speed, peak efficiency; 100% speed, near surge; and 95% speed, peak efficiency. At the design point, most passages appeared to have a strong leading edge shock, which moved forward with increasing strength near surge and at part speeds. The flow behind the shock was of a complex mixed subsonic and supersonic form. The intrablade flowfields were found to be significantly nonperiodic at 100% design speed, peak efficiency

Evidence of magnetic field quenching of phosphorous-doped silicon quantum dots

We present data on the electrical transport properties of highly-doped silicon-on-insulator quantum dots under the effect of pulsed magnetic fields up to 48 T. At low field intensities, B<7 T, we observe a strong modification of the conductance due to the destruction of weak localization whereas at higher fields, where the magnetic field length becomes comparable to the effective Bohr radius of phosphorous in silicon, a strong decrease in conductance is demonstrated. Data in the high and low electric field bias regimes are then compared to show that close to the Coulomb blockade edge magnetically-induced quenching to single donors in the quantum dot is achieved at about 40 T.Comment: accepted for publication at Current Applied Physic

Monitoring the defoliation of hardwood forests in Pennsylvania using LANDSAT

An automated system for conducting annual gypsy moth defoliation surveys using LANDSAT MSS data and digital processing techniques is described. A two-step preprocessing procedure was developed that uses multitemporal data sets representing forest canopy conditions before and after defoliation to create a digital image in which all nonforest cover types are eliminated or masked out of a LANDSAT image that exhibits insect defoliation. A temporal window for defoliation assessment was identified and a statewide data base was established. A data management system to interface image analysis software with the statewide data base was developed and a cost benefit analysis of this operational system was conducted

Cost-effectiveness analysis in R using a multi-state modelling survival analysis framework: a tutorial

This tutorial provides a step-by-step guide to performing cost-effectiveness analysis using a multi-state modelling approach. Alongside the tutorial we provide easy-to-use functions in the statistics package R. We argue this multi-state modelling approach using a package such as R has advantages over approaches where models are built in a spreadsheet package. In particular, using a syntax-based approach means there is a written record of what was done and the calculations are transparent. Reproducing the analysis is straightforward as the syntax just needs to be run again. The approach can be thought of as an alternative way to build a Markov decision analytic model, which also has the option to use a state-arrival extended approach if the Markov property does not hold. In the state-arrival extended multi-state model a covariate that represents patients’ history is included allowing the Markov property to be tested. We illustrate the building of multi-state survival models, making predictions from the models and assessing fits. We then proceed to perform a cost-effectiveness analysis including deterministic and probabilistic sensitivity analyses. Finally, we show how to create two common methods of visualising the results, namely cost-effectiveness planes and cost-effectiveness acceptability curves. The analysis is implemented entirely within R. It is based on adaptions to functions in the existing R package mstate, to accommodate parametric multi-state modelling which facilitates extrapolation of survival curves