6,455 research outputs found
High temperature deformation of dispersion strengthened nickel alloys. 1 - The influence of initial structure on tensile and creep deformation of TD nickel. 2 - The effect of matrix stacking fault energy on creep of Ni-Cr-ThO2 alloys Final report, 9 Feb. 1967 - 9 Feb. 1968
High temperature creep studies on unaltered, and recrystallized nickel alloy
The role of grain size and shape in the strengthening of dispersion hardened nickel alloys
Thermomechanical processing was used to develop various microsstructures in Ni, Ni-2ThO2, Ni-20Cr, Ni-20CR-2ThO2, Ni-20Cr-10W-and Ni-20Cr-10W-2ThO2. The yield strength at 25 C increased with substructure refinement according to the Hall-Petch relation, and substructure refinement was a much more potent means of strengthening than was dispersion hardening. At elevated temperature (1093 C), the most important microstructural feature affecting strength was the grain aspect ratio (grain length, L, divided by grain width, 1. The yield strength and creep strength increased linearly with increasing L/1
Development of high-emittance scales on thoriated nickel-chromium-aluminum-base alloys
The surface regions of a DSNiCrAl alloy have been doped, by a pack diffusion process, with small amounts of Mn, Fe, or Co, and the effect of these dopants on the total normal emissivity of the scales produced by subsequent high temperature oxidation has been measured. While all three elements lead to a modest increase in emissivity, (up to 23% greater than the undoped alloy) only the change caused by manganese is thermally stable. However, this increased emissivity is within 85 percent of that of TDNiCr oxidized to form a chromia scale. The maganese-doped alloy is some 50 percent weaker than undoped DSNiCrAl after the doping treatment, and approximately 30 percent weaker after oxidation
Total focussing method for volumetric imaging in immersion non destructive evaluation
This paper describes the use of a 550 (25x22) element 2MHz 2D piezoelectric composite array in immersion mode to image an aluminum test block containing a collection of artificial defects. The defects included a 1mm diameter side-drilled hole, a collection of 1mm slot defects with varying degrees of skew to the normal and a flat bottomed hole. The data collection was carried out using the full matrix capture; a scanning procedure was developed to allow the operation of the large element count array through a conventional 64-channel phased array controller. A 3D TFM algorithm capable of imaging in a dual media environment was implemented in MATLAB for the offline processing the raw scan data. This algorithm facilitates the creation of 3D images of defects while accounting for refraction effects at material boundaries. In each of the test samples interrogated the defects, and their spatial position, are readily identified using TFM. Defect directional information has been characterized using VTFM for defect exhibiting angles up to and including 45o of skew
Improving access to longitudinal patient health information within an emergency department
pre-printWe designed and implemented an electronic patient tracking system with improved user authentication and patient selection. We then measured access to clinical information from previous clinical encounters before and after implementation of the system. Clinicians accessed longitudinal information for 16% of patient encounters before, and 40% of patient encounters after the intervention, indicating such a system can improve clinician access to information. We also attempted to evaluate the impact of providing this access on inpatient admissions from the emergency department, by comparing the odds of inpatient admission from an emergency department before and after the improved access was made available. Patients were 24% less likely to be admitted after the implementation of improved access. However, there were many potential confounders, based on the inherent pre-post design of the evaluation. Our experience has strong implications for current health information exchange initiatives
Steady-state creep of dispersion-strengthened metals Final report
High temperature creep behavior of recrystallized nickel-thorium oxide alloys studied with vacuum constant-stress creep condition
High Reynolds number tests of a Douglas DLBA 032 airfoil in the Langley 0.3-meter transonic cryogenic tunnel
A wind-tunnel investigation of a Douglas advanced-technology airfoil was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-m TCT). The temperature was varied from 227 K (409 R) to 100 K (180 R) at pressures ranging from about 159 kPa (1.57 atm) to about 514 kPa (5.07 atm). Mach number was varied from 0.50 to 0.78. These variables provided a Reynolds number range (based on airfoil chord) from 6.0 to 30.0 x 10 to the 6th power. This investigation was specifically designed to: (1) test a Douglas airfoil from moderately low to flight-equivalent Reynolds numbers, and (2) evaluate sidewall-boundary-layer effects on transonic airfoil performance characteristics by a systematic variation of Mach number, Reynolds number, and sidewall-boundary-layer removal. Data are included which demonstrate the effects of fixing transition, Mach number, Reynolds number, and sidewall-boundary-layer removal on the aerodynamic characteristics of the airfoil. Also included are remarks on model design and model structural integrity
Crown and root rots of table grapes caused by Phytophthora spp. in Chile
Phytophthora crown and root rot of grapevine (Vitis vinifera L.) occurs frequently in Chile, where grapes are cultivated on their own roots. P. cinnamomi, P. cryptogea, and P. drechsleri were isolated from diseased root or crown tissue of the table grape cvs Flame Seedless, Italia, Red Globe, and Thompson Seedless with P. cryptogea being the most frequently isolated species. These pathogens were identified on the basis of standard morphological and cultural features and were compared by SDS-PAGE profiles of mycelial proteins. All isolates were pathogenic on 1-year-old cane segments and 1-year-old rooted grapevines of cvs Thompson Seedless and Red Globe. The latter cultivar was more susceptible than Thompson Seedless. P. cinnamomi and P. cryptogea have been associated with root rot of grapevines elsewhere, but this is the first report of P. drechsleri as a pathogen of grapevines and the first report of Phytophthora spp. affecting table grapes in Chile
- …