29,527 research outputs found
A cryogenic dc-dc power converter for a 100kW synchronous HTS generator at liquid nitrogen temperatures
A dc-dc converter has been developed for retrofitting inside the vacuum space of the HTS rotor of a synchronous generator. The heavy copper sections of the current leads used for energising the HTS field winding were replaced by cryogenic power electronics; consisting of the converter and a rotor control unit. The converter board was designed using an H-bridge configuration with two 5A rated wires connecting the cryogenic boards to the stator control board located on the outside of the generator and drawing power from a (5A, 50V) dc power source. The robustness of converter board was well demonstrated when it was powered up from a cold start at 82K. When charging the field winding with moderate currents (30A), the heat in-leak to the âcoldâ rotor core was only 2W. It continued to function down to 74K, surviving several quenches. However, the quench protection function failed when injecting 75A into the field winding, resulting in the burn out of one of the DC-link capacitors. The magnitudes of the critical currents measured with the original current leads were compared to the quench currents, which was defined as the current which triggered quench protection protocol. The difference between the two currents was rather large, (~20A). However, additional measurements using a single HTS coil in liquid nitrogen found that this reduction should not be so dramatic and in the region of 4A. Our conclusions identified the converterâs switching voltage and its operating frequency as two parameters, which could have contributed to lowering the quench current. Magnetic fields and eddy currents are expected to be more prominent the field winding and its impact on the converter also need further investigation
TEM investigation of YBa2Cu3O7 thin films on SrTiO3 bicrystals
YBa2Cu3O7 films in c-axis orientation on bicrystalline SrTiO3 substrates are investigated by TEM. The films and the substrates are examined in cross-section and in plane view. The grain boundary of the bicrystal substrate contains (110) faceted voids, but is otherwise straight on a nanometer scale. Contrary to this, the film grain boundary is not straight grain boundary can be up to 100 nm for a 100 nm thick film. The deviation from the intended position of the YBCO grain boundary can already occur at the film/substrate interface where it can be as much as ±50 nm
High-Efficient Parallel CAVLC Encoders on Heterogeneous Multicore Architectures
This article presents two high-efficient parallel realizations of the context-based adaptive variable length coding (CAVLC) based on heterogeneous multicore processors. By optimizing the architecture of the CAVLC encoder, three kinds of dependences are eliminated or weaken, including the context-based data dependence, the memory accessing dependence and the control dependence. The CAVLC pipeline is divided into three stages: two scans, coding, and lag packing, and be implemented on two typical heterogeneous multicore architectures. One is a block-based SIMD parallel CAVLC encoder on multicore stream processor STORM. The other is a component-oriented SIMT parallel encoder on massively parallel architecture GPU. Both of them exploited rich data-level parallelism. Experiments results show that compared with the CPU version, more than 70 times of speedup can be obtained for STORM and over 50 times for GPU. The implementation of encoder on STORM can make a real-time processing for 1080p @30fps and GPU-based version can satisfy the requirements for 720p real-time encoding. The throughput of the presented CAVLC encoders is more than 10 times higher than that of published software encoders on DSP and multicore platforms
Compressed Air Energy Storage-Part II: Application to Power System Unit Commitment
Unit commitment (UC) is one of the most important power system operation
problems. To integrate higher penetration of wind power into power systems,
more compressed air energy storage (CAES) plants are being built. Existing
cavern models for the CAES used in power system optimization problems are not
accurate, which may lead to infeasible solutions, e.g., the air pressure in the
cavern is outside its operating range. In this regard, an accurate CAES model
is proposed for the UC problem based on the accurate bi-linear cavern model
proposed in the first paper of this two-part series. The minimum switch time
between the charging and discharging processes of CAES is considered. The whole
model, i.e., the UC model with an accurate CAES model, is a large-scale mixed
integer bi-linear programming problem. To reduce the complexity of the whole
model, three strategies are proposed to reduce the number of bi-linear terms
without sacrificing accuracy. McCormick relaxation and piecewise linearization
are then used to linearize the whole model. To decrease the solution time, a
method to obtain an initial solution of the linearized model is proposed. A
modified RTS-79 system is used to verify the effectiveness of the whole model
and the solution methodology.Comment: 8 page
Fluidized bed combustor modeling
A general mathematical model for the prediction of performance of a fluidized bed coal combustor (FBC) is developed. The basic elements of the model consist of: (1) hydrodynamics of gas and solids in the combustor; (2) description of gas and solids contacting pattern; (3) kinetics of combustion; and (4) absorption of SO2 by limestone in the bed. The model is capable of calculating the combustion efficiency, axial bed temperature profile, carbon hold-up in the bed, oxygen and SO2 concentrations in the bubble and emulsion phases, sulfur retention efficiency and particulate carry over by elutriation. The effects of bed geometry, excess air, location of heat transfer coils in the bed, calcium to sulfur ratio in the feeds, etc. are examined. The calculated results are compared with experimental data. Agreement between the calculated results and the observed data are satisfactory in most cases. Recommendations to enhance the accuracy of prediction of the model are suggested
Evolution of magnetic component in Yang-Mills condensate dark energy models
The evolution of the electric and magnetic components in an effective
Yang-Mills condensate dark energy model is investigated. If the electric field
is dominant, the magnetic component disappears with the expansion of the
Universe. The total YM condensate tracks the radiation in the earlier Universe,
and later it becomes thus is similar to the cosmological constant.
So the cosmic coincidence problem can be avoided in this model. However, if the
magnetic field is dominant, holds for all time, suggesting that it
cannot be a candidate for the dark energy in this case.Comment: 12 pages, 4 figures, minor typos correcte
- âŠ