106,326 research outputs found
Orbital-resolved vortex core states in FeSe Superconductors: calculation based on a three-orbital model
We study electronic structure of vortex core states of FeSe superconductors
based on a t three-orbital model by solving the Bogoliubov-de
Gennes(BdG) equation self-consistently. The orbital-resolved vortex core states
of different pairing symmetries manifest themselves as distinguishable
structures due to different quasi-particle wavefunctions. The obtained vortices
are classified in terms of the invariant subgroups of the symmetry group of the
mean-field Hamiltonian in the presence of magnetic field. Isotropic and
anisotropic wave vortices have symmetry for each orbital, whereas
wave vortices show symmetry for orbitals
and symmetry for orbital. In the case of
wave vortices, hybridized-pairing between and orbitals gives
rise to a relative phase difference in terms of gauge transformed pairing order
parameters between and orbitals, which is essentially
caused by a transformation of co-representation of and
subgroup. The calculated local density of states(LDOS) of wave
vortices show qualitatively similar pattern with experiment results. The phase
difference of between and orbital-resolved
wave vortices can be verified by further experiment observation
Design of a 2.4 GHz High-Performance Up-Conversion Mixer with Current Mirror Topology
In this paper, a low voltage low power up-conversion mixer, designed in a Chartered 0.18 μm RFCMOS technology, is proposed to realize the transmitter front-end in the frequency band of 2.4 GHz. The up-conversion mixer uses the current mirror topology and current-bleeding technique in both the driver and switching stages with a simple degeneration resistor. The proposed mixer converts an input of 100 MHz intermediate frequency (IF) signal to an output of 2.4 GHz radio frequency (RF) signal, with a local oscillator (LO) power of 2 dBm at 2.3 GHz. A comparison with conventional CMOS up-conversion mixer shows that this mixer has advantages of low voltage, low power consumption and high-performance. The post-layout simulation results demonstrate that at 2.4 GHz, the circuit has a conversion gain of 7.1 dB, an input-referred third-order intercept point (IIP3) of 7.3 dBm and a noise figure of 11.9 dB, while drawing only 3.8 mA for the mixer core under a supply voltage of 1.2 V. The chip area including testing pads is only 0.62×0.65 mm2
Tungsten fibre reinforced Zr-based bulk metallic glass composites
A Zr-based bulk metallic glass (BMG) alloy with the composition (Zr55Al10Ni5Cu30)98.5Si1.5 was used as the base material to form BMG composites. Tungsten fiber reinforced BMG composites were successfully fabricated by pressure metal infiltration technique, with the volume fraction of the tungsten fiber ranging from 10% to 70%. Microstructure and mechanical properties of the BMG composites were investigated. Tungsten reinforcement significantly increased the material’s ductility by changing the compressive failure mode from single shear band propagation to multiple shear bands propagation, and transferring stress from matrix to tungsten fibers
Extending the Energy Framework for Network Simulator 3 (ns-3)
The problem of designing and simulating optimal transmission protocols for
energy harvesting wireless networks has recently received considerable
attention, thus requiring for an accurate modeling of the energy harvesting
process and a consequent redesign of the simulation framework to include it.
While the current ns-3 energy framework allows the definition of new energy
sources that incorporate the contribution of an energy harvester, the
integration of an energy harvester component into an existing energy source is
not straightforward using the existing energy framework. In this poster, we
propose an extension of the energy framework currently released with ns-3 in
order to explicitly introduce the concept of an energy harvester. Starting from
the definition of the general interface, we then provide the implementation of
two simple models for the energy harvester. In addition, we extend the set of
implementations of the current energy framework to include a model for a
supercapacitor energy source and a device energy model for the energy
consumption of a sensor. Finally, we introduce the concept of an energy
predictor, that gathers information from the energy source and harvester and
use this information to predict the amount of energy that will be available in
the future, and we provide an example implementation. As a result of these
efforts, we believe that our contributions to the ns-3 energy framework will
provide a useful tool to enhance the quality of simulations of energy-aware
wireless networks.Comment: 2 pages, 4 figures. Poster presented at WNS3 2014, Atlanta, G
- …