Influence of Alternation of Sulfate Attack and Freeze-Thaw on Microstructure of Concrete

The effects of sulfate attack and freeze-thaw alternation on the concrete microstructure were systemically investigated by advanced test methods such as water absorption method, air void analysis, XRD, and SEM. The experimental results indicated that freeze-thaw damage is the major effective factor in the sulfate attack and freeze-thaw alternation test. In the alternation test, average aperture of capillary pores of specimens was smaller, pores uniformity was better, and water absorption rate was lower than those specimens used in the single freeze-thaw damage test. The average aperture and uniformity of pores could be improved by adding fly ash and slag. Damage was accumulated in many cycles of freeze-thaw and microcracks increased during the test. At the same time, the hydration products of the concrete developed into expansive gypsum, AFt, and TSA without any strength during sulfate attack. The results of the microstructure analysis form XRD and SEM are in accordance with that of AFt, about 3 μm length, around which other hydration products decomposed by C-S-H after sulfate attack resulted in loss of concrete strength

Texture evolution induced by twinning and dynamic recrystallization in dilute Mg-1Sn-1Zn-1Al alloy during hot compression

Texture evolution of an extruded dilute Mg-1Sn-1Zn-1Al alloy was thoroughly investigated based on the twinning and dynamic recrystallization (DRX) behavior via hot compression at a strain rate of 10 s−1 and temperature of 225°C. It was found that the types and intensities of the texture are strongly dependent on the fraction of twins and DRX modes as well as regions where sub-grain boundaries (sub-GBs) are intensively accumulated. At the initial stage of deformation, the formation of compression direction (CD)-tilted basal texture was mainly determined by the occurrence of {101¯2} extension twins. As the strain increases, the variation in the texture intensity was greatly dominated by the DRX modes but the type of main texture remained unchanged. These findings are of great importance for texture modification of wrought Mg-Sn-based alloys during post-deformation

Strong Convergence of Monotone Hybrid Algorithm for Hemi-Relatively Nonexpansive Mappings

The purpose of this article is to prove strong convergence theorems for fixed points of closed hemi-relatively nonexpansive mappings. In order to get these convergence theorems, the monotone hybrid iteration method is presented and is used to approximate those fixed points. Note that the hybrid iteration method presented by S. Matsushita and W. Takahashi can be used for relatively nonexpansive mapping, but it cannot be used for hemi-relatively nonexpansive mapping. The results of this paper modify and improve the results of S. Matsushita and W. Takahashi (2005), and some others

A fully integrated RSSI and an ultra-low power SAR ADC for 5.8 GHz DSRC ETC transceiver

This study presents a monolithic received signal strength indicator (RSSI) and an ultra-low power SAR ADC for 5.8 GHz DSRC transceiver in China electronic toll collection systems. In order to meet the stringent requirement of wide input range for the transceiver, two RSSIs collaborate with auxiliary ADC circuits to provide the digitalized received signal strength to the digital baseband of a transceiver. The RSSI design achieves fast transient response and low power consumption with a small die area by using internal active low-pass filters instead of external passive ones. The proposed design has been fabricated using a 0.13 μm 2P6M CMOS technology. Measurement results show that the overall input dynamic range is 86 dB with an accuracy of ±1.72 dB and a transient response of less than 2 μs. Compared with the state-of-the-art designs in the literature, the overall input range and transient settling time are improved by at least 14.6%, and 300%, respectively

Seasonal Characteristics of Black Carbon Aerosol and its Potential Source Regions in Baoji, China

Continuous measurements of black carbon (BC) aerosol were made at a midsized urban site in Baoji, China, in 2015. The daily average mass concentrations varied from 0.6 to 11.5 mu g m(-3), with an annual mean value of 2.9 +/- 1.7 mu g m(-3). The monthly variation indicated that the largest loading of BC occurred in January and the smallest in June. The mass concentrations exhibited strong seasonality, with the highest occurring in winter and the lowest in summer. The large BC loadings in winter were attributed to the increased use of fuel for domestic heating and to stagnant meteorological conditions, whereas the low levels in summer were related to the increase in precipitation. BC values exhibited similar bimodal diurnal patterns during the four seasons, with peaks occurring in the morning and evening rush hours and an afternoon trough, which was associated with local anthropogenic activities and meteorological conditions. A potential source contribution function model indicated that the effects of regional transport mostly occurred in spring and winter. The most likely regional sources of BC in Baoji were southern Shaanxi province, northwestern Hubei province, and northern Chongqing during spring, whereas the northeastern Sichuan Basin was the most important source region during winter