6,211 research outputs found
Cracks in glass electrical connector headers removed by dry blasting with fine abrasive
Cracking that causes pressure leakage in glass connector headers can be alleviated by manipulating the pin bridgewire connectors. This initiates the surface and meniscus cracks. Dry blasting the header surface with a fine abrasive then removes the cracks
Aerodynamic design guidelines and computer program for estimation of subsonic wind tunnel performance
General guidelines are given for the design of diffusers, contractions, corners, and the inlets and exits of non-return tunnels. A system of equations, reflecting the current technology, has been compiled and assembled into a computer program (a user's manual for this program is included) for determining the total pressure losses. The formulation presented is applicable to compressible flow through most closed- or open-throat, single-, double-, or non-return wind tunnels. A comparison of estimated performance with that actually achieved by several existing facilities produced generally good agreement
Low-speed wind tunnel investigation of the lateral-directional characterisitcs of a large-scale variable wing-sweep fighter model in the high-lift configuration
The low-speed characteristics of a large-scale model of the F-14A aircraft were studied in tests conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel. The primary purpose of the present tests was the determination of lateral-directional stability levels and control effectiveness of the aircraft in its high-lift configuration. Tests were conducted at wing angles of attack between minus 2 deg and 30 deg and with sideslip angles between minus 12 deg and 12 deg. Data were taken at a Reynolds number of 8.0 million based on a wing mean aerodynamic chord of 2.24 m (7.36 ft). The model configuration was changed as required to show the effects of direct lift control (spoilers) at yaw, yaw angle with speed brake deflected, and various amounts and combinations of roll control
Thermal stability and grain growth behavior of mechanically alloyed nanocrystalline Fe-Cu alloys
X-ray diffraction, transmission electron microscopy, and differential scanning calorimetry were used to study the thermal stability of highly supersaturated nanocrystalline FexCu100−x alloys (10~80. For 60<=x<=80 fcc and bcc phases coexist. Heating to elevated temperatures leads to structural relaxation, phase separation, and grain growth of the metastable nanocrystalline solid solutions. Single-phase fcc and bcc alloys undergo significant strain release but no appreciable grain growth prior to phase separation. After phase separation pronounced grain growth sets in. In contrast, samples in the two-phase region show some grain growth and significant chemical redistribution even at low temperatures. The phase separation of single-phase fcc and bcc alloys proceeds via different mechanisms: fcc solid solutions decompose by forming small Fe precipitates, while demixing in bcc alloys starts by segregation of Cu atoms to bcc grain boundaries before nucleation of Cu precipitates. These results show that the stability and grain growth behavior of nanocrystalline alloys is strongly affected by the microstructure of the material
Wind sensitivity studies of a non-return wind tunnel with a 216- by 432-mm (8.5- by 17.0-inches) test section, phase 2
The refinement of inlet and exit treatments were studied which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel. The investigation was conducted in the Ames Research Center 40- by 80-foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios from zero to somewhat greater than one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three component directions generally less. The loss in total pressure due to the inlet treatment was low: about 0.035 of the test-section dynamic pressure for the no-wind case
An aerodynamic investigation of two 1.83-meter-diameter fan systems designed to drive a subsonic wind tunnel
An experimental, aerodynamic investigation was made of two 1.83 m diameter fan systems which are being considered for the repowered drive section of the 40- by 80-foot wind tunnel at NASA Ames Research Center. One system was low speed, the other was high speed. The low speed fan was tested at various stagger angles from 32.9 deg to 62.9 deg. At a fan blade stagger angle of 40.8 deg and operating at a tip speed of 1155 m/sec, the low speed fan developed 207.3 m of head. The high speed fan had a design blade stagger angle of 56.2 deg and was tested at this stagger angle only. The high speed fan operating at 191.5 m/sec developed 207.3 m of head. Radial distributions of static pressure coefficients, total pressure coefficients, and angles of swirl are presented. Radial surveys were conducted at four azimuth locations in front of the fan, and repeated downstream of the fan. Data were taken for various flow control devices and for two inlet contraction lengths
Wind sensitivity studies of a non-return wind tunnel, with a 216- by 432-mm (8.5- by 17.0-inch) test section, phase 1
The study to develop inlet and exit treatments which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel is reported. The investigation was conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios between zero and one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three directions generally less than 1/2 knot (0.26 m/sec) for wind velocities of 15 knots (7.7 m/sec) or less. The loss in total pressure due to the inlet treatment was low: about 0.03 of the test-section dynamic pressure
Measurement of Prandtl number and thermal conductivity Summary report
Prandtl numbers and thermal conductivity of air, argon, and hydrocarbon fuel combustion product
A Look at the Declining Membership of Tennessee Association of Plumbing, Heating, Cooling Contractors, Inc.
- …