Multigrid for hypersonic viscous two- and three-dimensional flows

The use of a multigrid method with central differencing to solve the Navier-Stokes equations for hypersonic flows is considered. The time dependent form of the equations is integrated with an explicit Runge-Kutta scheme accelerated by local time stepping and implicit residual smoothing. Variable coefficients are developed for the implicit process that removes the diffusion limit on the time step, producing significant improvement in convergence. A numerical dissipation formulation that provides good shock capturing capability for hypersonic flows is presented. This formulation is shown to be a crucial aspect of the multigrid method. Solutions are given for two-dimensional viscous flow over a NACA 0012 airfoil and three-dimensional flow over a blunt biconic

Mechanosensing and Chemical Signaling in Single Osteocytes

Klein Nulend, J. [Promotor]Smit, T.H. [Copromotor

Development of Unsteady Aerodynamic and Aeroelastic Reduced-Order Models Using the FUN3D Code

Recent significant improvements to the development of CFD-based unsteady aerodynamic reduced-order models (ROMs) are implemented into the FUN3D unstructured flow solver. These improvements include the simultaneous excitation of the structural modes of the CFD-based unsteady aerodynamic system via a single CFD solution, minimization of the error between the full CFD and the ROM unsteady aero- dynamic solution, and computation of a root locus plot of the aeroelastic ROM. Results are presented for a viscous version of the two-dimensional Benchmark Active Controls Technology (BACT) model and an inviscid version of the AGARD 445.6 aeroelastic wing using the FUN3D code

Comparative Study of Active Flow Control Strategies for Lift Enhancement of a Simplified High-Lift Configuration

Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of the conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-AFC configuration to recover the aerodynamic performance (lift) of the CRM-HL configuration. In the current paper, a Lattice Boltzmann method-based computational fluid dynamics (CFD) code, known as PowerFLOWQ is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with several different types of AFC devices. The transonic version of the PowerFLOWQ code that has been validated for high speed flows is used to accurately simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. The numerical solutions predict the expected trends in aerodynamic forces as the actuation levels are increased. More efficient AFC systems and actuator arrangements emerged based on the parametric studies performed prior to a Fall 2018 wind tunnel test. Preliminary comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations

Wind Tunnel Testing of Active Flow Control on High-Lift Common Research Model

A 10%-scale high-lift version of the Common Research Model (CRM-HL) and an Active Flow Control (AFC) version of the model equipped with a simple-hinged flap (CRM-SHLAFC) were successfully tested. The tests were performed in the 14- by 22-Foot Subsonic Tunnel (14x22) at the NASA Langley Research Center (LaRC). The CRM-HL has a set of 37 inboard and outboard single-element Fowler flaps. The CRM-SHL-AFC has a set of 50 inboard and 55 outboard simple-hinged flaps equipped with integrated modular AFC cartridges on the flap shoulder. Both high-lift configurations share the same 30 slats and engine nacelle. Three new types of AFC devices were examined: the Double-Row Sweeping Jets (DRSWJ), the Alternating Pulsed Jets (APJ), and the High Efficiency Low Power (HELP) actuators. The DRSWJ and the APJ actuators used two rows of unsteady jets, whereas the HELP actuators used a combination of unsteady and steady jets, to overcome strong adverse pressure gradients while minimizing the mass flow usage. Nozzle pressure ratio, mass flow consumption and the power coefficient, which takes account of both supply air pressure and mass flow usage for the actuators, were used for judging the performance efficiency of the AFC devices. A prestall lift performance degradation for the CRM-HL configuration was resolved with a properly placed nacelle chine. The configuration with nacelle chine was chosen as the representative reference conventional high-lift case for comparison with the CRMSHL- AFC. The AFC-induced lift coefficient increment (DCL) was maintained for the entire lift curve over the CRM-SHL-AFC case with no AFC for almost all flow-control cases examined. The lift curve of the reference CRM-HL have a slightly steeper slope compared to those of the CRM-SHL-AFC configurations. The HELP actuation concept was extremely effective in controlling flow separation in the linear region of the curves comparing lift coefficient to mass flow rate. The HELP actuation achieved a targeted DCL of 0.50 using a moderate amount of mass flow and supply air pressure. The CRM-SHL-AFC configuration equipped with HELP actuation was able to match or exceed the lift performance of the reference conventional high-lift configuration (i.e., CRM-HL equipped with a nacelle chine), thus meeting the NASA Advanced Air Transport Technology (AATT) project goal

Aeroacoustic Simulation of Nose Landing Gear on Adaptive Unstructured Grids With FUN3D

Numerical simulations have been performed for a partially-dressed, cavity-closed nose landing gear configuration that was tested in NASA Langley s closed-wall Basic Aerodynamic Research Tunnel (BART) and in the University of Florida's open-jet acoustic facility known as the UFAFF. The unstructured-grid flow solver FUN3D, developed at NASA Langley Research center, is used to compute the unsteady flow field for this configuration. Starting with a coarse grid, a series of successively finer grids were generated using the adaptive gridding methodology available in the FUN3D code. A hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) turbulence model is used for these computations. Time-averaged and instantaneous solutions obtained on these grids are compared with the measured data. In general, the correlation with the experimental data improves with grid refinement. A similar trend is observed for sound pressure levels obtained by using these CFD solutions as input to a FfowcsWilliams-Hawkings noise propagation code to compute the farfield noise levels. In general, the numerical solutions obtained on adapted grids compare well with the hand-tuned enriched fine grid solutions and experimental data. In addition, the grid adaption strategy discussed here simplifies the grid generation process, and results in improved computational efficiency of CFD simulations

Summary of the 2004 CFD Validation Workshop on Synthetic Jets and Turbulent Separation Control

A computational fluid dynamics (CFD) validation workshop for synthetic jets and turbulent separation control (CFDVAL2004) was held in Williamsburg, Virginia in March 2004. Three cases were investigated: synthetic jet into quiescent air, synthetic jet into a turbulent boundary layer crossflow, and flow over a hump model with no-flow-control, steady suction, and oscillatory control. This paper is a summary of the CFD results from the workshop. Although some detailed results are shown, mostly a broad viewpoint is taken, and the CFD state-of-the-art for predicting these types of flows is evaluated from a general point of view. Overall, for synthetic jets, CFD can only qualitatively predict the flow physics, but there is some uncertainty regarding how to best model the unsteady boundary conditions from the experiment consistently. As a result, there is wide variation among CFD results. For the hump flow, CFD as a whole is capable of predicting many of the particulars of this flow provided that tunnel blockage is accounted for, but the length of the separated region compared to experimental results is consistently overpredicted

Stratégie de grille conforme octrée intersectées pour les Applications aux calculs Aéroacoustiques de LAGOON, Modèle de train d'Atterrissage, utilisant le Flow Solver CEDRE non structuré

International audienceAircraft noise is a societal concern and landing gears contribute significantly to the generated noise in approach and landing configurations. Landing gears are characterized by their complex geometry and numerous works have been carried out to develop and validate aeroacoustics simulations to predict the associated noise. Most of them associate a time resolved flow solution, to capture the acoustic sources, to an acoustic computation, to estimate the resulting far field noise. Due to the geometric complexity, unstructured grids are required and may necessitate meticulous work to optimize. In this context, Lattice Boltzmann Methods (LBM) have become popular as they propose to combine automatic grid generation and high CPU efficiency and produced remarked results. The automatic grid generation is facilitated by the use of advanced wall models that do not require resolution of complex details of boundary layer flow, ranging from attached to detached regimes, that are produced by the complex geometries and flow environment of landing gears. Navier-Stokes (NS) solvers on the contrary rely on precise boundary layer solution that require complex grids, even in the unstructured approach, to handle the attached boundary layer regimes, that require strong grid anisotropy, as well as detached regimes and their trailing flow, that require grid isotropy. The grid construction work can therefore become a complex process. The simplification of this process is then an important challenge for industrial applications. The present work details a multi-year effort at ONERA in that direction

Surface Flow Visualization of the High-Lift Common Research Model

A 10% scale version of the High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The CRM-HL experiment included various configurations such as conventional and simple-hinged flaps, with and without engine nacelle/pylon, with and without nacelle chine, different Active Flow Control (AFC) methods (sweeping jets, alternating pulsed jets, and preconditioned boundary layer blowing), and their various parameters. This particular study is focused on the surface flow visualization of the conventional CRM-HL model at landing configuration. The conventional CRM-HL model with the single-slotted Fowler flap system serves as a baseline for the AFC-enabled simplified high-lift configuration as well as a high-lift technology development platform due to its publicly open geometry. Surface flow visualizations were performed using fluorescent minitufts, which were found to be nonintrusive to the aerodynamic performance. Tuft flow visualizations are supplemented with the relevant pressure and force measurements in order to understand the flow characteristics developed on the conventional CRM- HL model. In addition, three dimensional, unsteady, compressible Computational Fluid Dynamic (CFD) simulations were performed for selective cases. The surface streamlines and transverse velocity fluctuations obtained by the CFD simulations are qualitatively compared to the tuft direction and tuft unsteadiness, respectively. Force measurements of the CRM-HL model show performance degradation at higher angles of attack. Surface flow visualizations revealed the performance loss due to the nacelle/pylon wake that grows with angle of attack and eventually promotes flow separation over the inboard wing. This performance loss was successfully recovered by placing a chine on the engine nacelle