83 research outputs found

    Acoustic guide for noise-transmission testing of aircraft

    Get PDF
    Selective testing of aircraft or other vehicular components without requiring disassembly of the vehicle or components was accomplished by using a portable guide apparatus. The device consists of a broadband noise source, a guide to direct the acoustic energy, soft sealing insulation to seal the guide to the noise source and to the vehicle component, and noise measurement microphones, both outside the vehicle at the acoustic guide output and inside the vehicle to receive attenuated sound. By directing acoustic energy only to selected components of a vehicle via the acoustic guide, it is possible to test a specific component, such as a door or window, without picking up extraneous noise which may be transmitted to the vehicle interior through other components or structure. This effect is achieved because no acoustic energy strikes the vehicle exterior except at the selected component. Also, since the test component remains attached to the vehicle, component dynamics with vehicle frame are not altered

    Cabin Noise Control for Twin Engine General Aviation Aircraft

    Get PDF
    An analytical model based on modal analysis was developed to predict the noise transmission into a twin-engine light aircraft. The model was applied to optimize the interior noise to an A-weighted level of 85 dBA. To achieve the required noise attenuation, add-on treatments in the form of honeycomb panels, damping tapes, acoustic blankets, septum barriers and limp trim panels were added to the existing structure. The added weight of the noise control treatment is about 1.1 percent of the total gross take-off weight of the aircraft

    Design of sidewall treatment of cabin noise control of a twin engine turboprop aircraft

    Get PDF
    An analytical procedure was used to predict the noise transmission into the cabin of a twin engine general aviation aircraft. This model was then used to optimize the interior A weighted noise levels to an average value of about 85 dBA. The surface pressure noise spectral levels were selected utilizing experimental flight data and empirical predictions. The add on treatments considered in this optimization study include aluminum honeycomb panels, constrained layer damping tape, porous acoustic blankets, acoustic foams, septum barriers and limp trim panels which are isolated from the vibration of the main sidewall structure. To reduce the average noise level in the cabin from about 102 kBA (baseline) to 85 dBA (optimized), the added weight of the noise control treatment is about 2% of the total gross takeoff weight of the aircraft

    A primer for structural response to random pressure fluctuations

    Get PDF
    A review was made of power spectral methods for determining linear response of structures to random pressure fluctuations. Various simplifying assumptions are made for the purpose of obtaining useful formula for structural response. The transmission of sound through a flexible structure into an interior cavity was also treated

    Vibration and structureborne noise in space station

    Get PDF
    Analytical models and computer programs for structural response calculations under action of mechanical point loads were developed for single wall shells (composite or aluminum), double wall shells (composite or aluminum), and single wall or double wall circular plates (aluminum). The design configuration of the habitability modules of the space station concept are expected to be discretely stiffened cylindrical shells with truncated cone type end caps or flat but stiffened circular end plates. Analytical formulations and response calculations were performed for the case where the stiffened shell is represented by an orthotropic shell model. The natural frequencies can be calculated. For application to low frequency (below 1000Hz) vibrations and noise generation, such a model might be adequate to evaluate vibration and noise transmission characteristics of space station habitability modules. Parametric studies are now being performed to assess interior noise environment inside a habitability module to mechanically induced vibrations

    Aircraft cabin noise prediction and optimization

    Get PDF
    Theoretical and experimental studies were conducted to determine the noise transmission into acoustic enclosures ranging from simple rectangular box models to full scale light aircraft in flight. The structural models include simple, stiffened, curved stiffened, and orthotropic panels and double wall windows. The theoretical solutions were obtained by model analysis. Transfer matrix and finite element procedures were utilized. Good agreement between theory and experiment has been achieved. An efficient acoustic add-on treatment was developed for interior noise control in a twin engine light aircraft

    Noise transmission through plates into an enclosure

    Get PDF
    An analytical model is presented to predict noise transmission through elastic plates into a hard-walled rectangular cavity at low frequencies, that is, frequencies up through the first few plate and cavity natural frequencies. One or several nonoverlapping and independently vibrating panels are considered. The effects on noise transmission of different external-pressure excitations, plate boundary conditions, fluid parameters, structural parameters, and geometrical parameters were investigated

    Vibrations and structureborne noise in space station

    Get PDF
    Theoretical models were developed capable of predicting structural response and noise transmission to random point mechanical loads. Fiber reinforced composite and aluminum materials were considered. Cylindrical shells and circular plates were taken as typical representatives of structural components for space station habitability modules. Analytical formulations include double wall and single wall constructions. Pressurized and unpressurized models were considered. Parametric studies were conducted to determine the effect on structural response and noise transmission due to fiber orientation, point load location, damping in the core and the main load carrying structure, pressurization, interior acoustic absorption, etc. These analytical models could serve as preliminary tools for assessing noise related problems, for space station applications

    Response of space shuttle insulation panels to acoustic noise pressure

    Get PDF
    The response of reusable space shuttle insulation panels to random acoustic pressure fields are studied. The basic analytical approach in formulating the governing equations of motion uses a Rayleigh-Ritz technique. The input pressure field is modeled as a stationary Gaussian random process for which the cross-spectral density function is known empirically from experimental measurements. The response calculations are performed in both frequency and time domain

    Vibrations and structureborne noise in space station

    Get PDF
    The related literature was reviewed and a preliminary analytical model was developed for simplified acoustic and structural geometries for pressurized and unpressurized space station modules. In addition to the analytical work, an experimental program on structureborne noise generation and transmission was started. A brief review of those accomplishments is given
    corecore