Excerpts of Daivavyapashraya Chikitsa in unpublished manuscript Kashyapa Samhita - A New Outlook

The concept of Daivavyapashraya Chikitsa (a modality of treatment based on past deeds and pleasing of god) has been given least importance in the available Ayurvedic classics. Here is the study of a manuscript named Kashyapa Samhita which is quite different from deemed Kashyapa Samhita that is known off. The study was carried out by deciphering and critically editing six manuscripts collected from IPGT & RA (with accession no. 6512 and 10779), Tanjore Sarasvati Mahal Library (with accession no. 11045), Sampurnananda Library, Varanasi (with accession no. 1088604) and Oriental Research Institute, Mysore (with accession no. A129), MS University Baroda Library (with accession no. 13474B). This manuscript brings out ample references regarding Daivavyapashraya Chikitsa for different diseases caused due to sinful acts

Microstructure of selective laser melted CM247LC nickel-based superalloy and its evolution through heat treatment

The selective laser melting of high temperature alloys is of great interest to the aerospace industry as it offers the prospect of producing more complex geometries than can be achieved with other manufacturing methods. In this study, the microstructure of the nickel-based superalloy, CM247LC, has been characterised following selective laser melting and after a post deposition heat-treatment below the γʹ solvus temperature. In the as-deposited state, scanning electron microscopy with electron backscatter diffraction revealed a fine, cellular microstructure with preferential alignment of along the build direction. A high dislocation density was seen at the periphery of the cells, indicating substantial localised deformation of the material. Fine primary MC carbides were also observed in the inter-cellular regions. High-resolution transmission electron microscopy identified the occurrence of very fine γʹ precipitates, approximately 5 nm in diameter, dispersed within the gamma phase. After heat treatment, the elongated cell colonies were observed to partially coalesce, accompanied by a decrease in dislocation density, producing columnar grains along the build direction. Cuboidal γʹ precipitates approximately 500 nm in diameter were observed to form in the recrystallised grains, accompanied by larger γʹ precipitates on the grain boundaries.The authors acknowledge funding from the EU under the Seventh Framework Programme (FP7) through the ASLAM project (CfP topic number: JTI-CS-2013-01-SAGE-06-006Project reference number: 619993). The authors would also like to acknowledge Rolls-Royce plc. for providing conventionally cast CM247LC.This is the author accepted manuscript. The final version is available from Elsevier via http://dx.doi.org/10.1016/j.matchar.2016.02.00

Microstructural control and optimization of Haynes 282 manufactured through laser powder bed fusion

The microstructure and properties of alloy Haynes 282 produced through laser powder bed fusion were investigated as a function of the post-deposition heat-treatment. Scanning electron microscopy and X-ray diffraction were utilized to characterize the microstructure, whilst electro-thermal mechanical testing was used to evaluate the tensile and creep properties at 900 °C. In the as-deposited state, the initial microstructure consisted of the γ and γʹ phases along with M6C and M23C6 carbides. These carbides were observed to govern the recrystallization behaviour of the material and resulted in a minimum recrystallization temperature of 1240 °C. Following post-deposition heat-treatments, the microstructures consisted of a monomodal distribution of γʹ with M6C and M23C6 carbides along the grain boundaries. Tertiary γʹ particles were found to form in the vicinity of carbides in samples that employed a γʹ super-solvus step prior to ageing at 788 °C. The tensile properties were found to be similar in all heat-treated states, consistent with the minimal differences observed in the microstructures. In contrast, significant differences in the creep behaviour of the alloy were observed following the different heat-treatments, although no correlation with the microstructures was observed

A Survey of Bayesian Statistical Approaches for Big Data

The modern era is characterised as an era of information or Big Data. This has motivated a huge literature on new methods for extracting information and insights from these data. A natural question is how these approaches differ from those that were available prior to the advent of Big Data. We present a review of published studies that present Bayesian statistical approaches specifically for Big Data and discuss the reported and perceived benefits of these approaches. We conclude by addressing the question of whether focusing only on improving computational algorithms and infrastructure will be enough to face the challenges of Big Data

Interdiffusion Studies in the Co- Mo System

Study of interdiffusion in the Co-Mo system is important to understand the performance of turbine blades in jet engine applications. Mo is added to superalloys to increase the solid solution strengthening and the creep resistance. In this study, the interdiffusion coefficient in the Co(Mo) solid solution and impurity diffusion coefficient of Mo in Co are determined. Further, the activation energy and pre-exponential factors are calculated, which provide an idea about the atomic mechanism of diffusion

Topological close packed mu phase formation and the determination of diffusion parameters in the Co-Mo system

The study on the formation and growth of topological close packed (TCP) compounds is important to understand the performance of turbine blades in jet engine applications. These deleterious phases grow mainly by diffusion process in the superalloy substrate. Significant volume change was found because of growth of the p phase in Co-Mo system. Growth kinetics of this phase and different diffusion parameters, like interdiffusion, intrinsic and tracer diffusion coefficients are calculated. Further the activation energy, which provides an idea about the mechanism, is determined. Moreover, the interdiffusion coefficient in Co(Mo) solid solution and impurity diffusion coefficient of Mo in Co are determined

Interdiffusion and Growth of the Phases in CoNi/Mo and CoNi/W Systems

Deleterious topological-closed-packed (tcp) phases grow in the interdiffusion zone in turbine blades mainly because of the addition of refractory elements such as Mo and W in the Ni- and Co-based superalloys. CoNi/Mo and CoNi/W diffusion couples are prepared to understand the growth mechanism of the phases in the interdiffusion zone. Instead of determining the main and cross-interdiffusion coefficients following the conventional method, we preferred to determine the average effective interdiffusion coefficients of two elements after fixing the composition of one element more or less the same in the interdiffusion zone. These parameters can be directly related to the growth kinetics of the phases and shed light on the atomic mechanism of diffusion. In both systems, the diffusion rate of elements and the phase layer thickness increased because of the addition of Ni in the solid solution phase, probably because of an increase in driving force. On the other hand, the growth rate of the mu phase and the diffusion coefficient of the species decreased because of the addition of Ni. This indicates the change in defect concentration, which assists diffusion. Further, we revisited the previously published Co-Ni-Mo and Co-Ni-W ternary phase diagrams and compared them with the composition range of the phases developed in the interdiffusion zone. Different composition ranges of the tcp phases are found, and corrected phase diagrams are shown. The outcome of this study will help to optimize the concentration of elements in superalloys to control the growth of the tcp phases

Interdiffusion and the vacancy wind effect in Ni-Pt and Co-Pt systems

In this study, bulk and multifoil diffusion couple experiments were conducted to examine the interdiffusion process in Ni-Pt and Co-Pt binary alloy systems. Inter-, intrinsic-, and tracer-diffusion coefficients at different temperatures, and as a function of the composition, were estimated by using the experimental data. Results show that in both the alloy systems, Pt is the slower diffusing species, and hence the interdiffusion process is controlled by either Ni or Co. The thermodynamic driving force makes the intrinsic diffusion coefficients of Co and Ni higher in the range of 30-70 at.%. The low activation energy for Co and Ni impurity diffusion in Pt compared with Pt in Ni and Co indicates that the size of the atoms plays an important role. The vacancy wind effects on the diffusion process are examined in detail, and it was demonstrated that its contribution falls within the experimental scatter and hence can be neglected

Interdiffusion and solid solution strengthening in Ni-Co-Pt and Ni-Co-Fe ternary systems

Diffusion couple experiments are conducted in Co-Ni-Pt system at 1200 degrees C and in Co-Ni-Fe system at 1150 degrees C, by coupling binary alloys with the third element. Uphill diffusion is observed for both Co and Ni in Pt rich corner of the Co-Ni-Pt system, whereas in the Co-Ni-Fe system, it is observed for Co. Main and cross interdiffusion coefficients are calculated at the composition of intersection of two independent diffusion profiles. In both the systems, the main interdiffusion coefficients are positive over the whole composition range and the cross interdiffusion coefficients show both positive and negative values at different regions. Hardness measured by performing the nanoindentations on diffusion couples of both the systems shows the higher values at intermediate compositions

Evaluation of Solid-Solution Hardening in Several Binary Alloy Systems Using Diffusion Couples Combined with Nanoindentation

Analysis of solid-solution hardening (SSH) in alloys requires the synthesis of large composition libraries and the measurement of strength or hardness from these compositions. Conventional methods of synthesis and testing, however, are not efficient and high-throughput approaches have been developed in the past. In the present study, we use a high-throughput combinatorial approach to examine SSH at large concentrations in binary alloys of Fe-Ni, Fe-Co, Pt-Ni, Pt-Co, Ni-Co, Ni-Mo, and Co-Mo. The diffusion couple (DC) method is used to generate concentration (c) gradients and the nanoindentation (NI) technique to measure the hardness (H) along these gradients. The obtained H -c profiles are analyzed within the framework of the Labusch model of SSH, and the dependence of H predicted by the model is found to be generally applicable. The SSH behavior obtained using the combinatorial method is found to be largely consistent with that observed in the literature using conventional and DC-NI methods. This study evaluates SSH in Fe-, Ni-, Co-, and Pt-based binary alloys and confirms the applicability of the DC-NI approach for rapidly screening various solute elements for their SSH ability