Physicomechanical properties of the extracellular matrix of a demineralized bone

The article describes the results of a study of physicomechanical properties of a demineralized bone matrix of human cancellous and compact bones. A demineralized cancellous bone was shown to have the best characteristics of a porous system for colonization of matrices by cells. The ultimate stress and elasticity modulus of samples of demineralized femoral heads isolated in primary hip replacement was demonstrated to vary in wide ranges. The elasticity modulus ranged from 50 to 250 MPa, and the tensile strength varied from 1.1 to 5.5 MPa. Microhardness measurements by the recovered indentation method were not possible because of the viscoelastic properties of a bone material. To study the piezoelectric properties of samples, a measuring system was developed that comprised a measuring chamber with contact electrodes, a system for controlled sample loading, an amplifier-converter unit, and signal recording and processing software. The measurement results were used to determine the dependence of the signal amplitude on the dynamic deformation characteristics. The findings are discussed in terms of the relationship between the mechanical and electrical properties and the structure of the organic bone component

Physicomechanical properties of the extracellular matrix of a demineralized bone

The article describes the results of a study of physicomechanical properties of a demineralized bone matrix of human cancellous and compact bones. A demineralized cancellous bone was shown to have the best characteristics of a porous system for colonization of matrices by cells. The ultimate stress and elasticity modulus of samples of demineralized femoral heads isolated in primary hip replacement was demonstrated to vary in wide ranges. The elasticity modulus ranged from 50 to 250 MPa, and the tensile strength varied from 1.1 to 5.5 MPa. Microhardness measurements by the recovered indentation method were not possible because of the viscoelastic properties of a bone material. To study the piezoelectric properties of samples, a measuring system was developed that comprised a measuring chamber with contact electrodes, a system for controlled sample loading, an amplifier-converter unit, and signal recording and processing software. The measurement results were used to determine the dependence of the signal amplitude on the dynamic deformation characteristics. The findings are discussed in terms of the relationship between the mechanical and electrical properties and the structure of the organic bone component

СВОЙСТВА ДЕМИНЕРАЛИЗОВАННОГО КОСТНОГО МАТРИКСА ДЛЯ БИОИНЖЕНЕРИИ ТКАНЕЙ

The purpose. Determination of tissues of physico-mechanical properties of demineralized bone matrix of spongy and compact human bone important for bioengineering.Material and Methods.The methods for studying micromorphological, piezoelectric and transport properties, adapted for measuring the materials of potential scaffolds.Results. The results of studying the physico-mechanical properties of the demineralized bone matrix of spongy and compact human bones are presented. It is shown that the demineralized spongy bone possesses the best characteristics of the pore system for the colonization of matrix cells. The tensile strength and modulus of elasticity of samples from the demineralized heads of the femurs extracted during the initial hip arthroplasty vary widely. The modulus of elasticity varied from 50 to 250 MPa, and the ultimate strength was from 1.1 to 5.5 MPa.Conclusion. Methods for measuring micromorphological, piezoelectric and transport properties for materials of potential matrices were developed and / or adapted. It is shown that in the samples of materials from the human bone, these characteristics, as a rule, vary considerably. Proceeding from this, it becomes obvious that the development of protocols of measurement methods of the above listed properties is an important work for the creation of technology of bioengineering of tissue implants for reconstructive surgery. Цель. Определение значимых для биоинженерии тканей физико-механических свойств деминерализованного костного матрикса губчатой и компактной кости человека.Материалы и методы. Перечислены методы исследования микроморфологических, пьезоэлектрических и транспортных свойств, адаптированные для измерения у материалов потенциальных матриц.Результаты. Приведены результаты исследования физико-механических свойств деминерализованного костного матрикса губчатой и компактной кости человека. Показано, что деминерализованная губчатая кость обладает наилучшими характеристиками поровой системы для заселения матриксов клетками. Предел прочности и модуль упругости образцов из деминерализованных головок бедренных костей, извлеченных в ходе первичного эндопротезирования тазобедренного сустава, изменяются в широких пределах. Модуль упругости изменялся от 50 до 250 МПа, а предел прочности – от 1,1 до 5,5 МПа.Заключение. Были отработаны и/или адаптированы методы измерений микроморфологических, пьезоэлектрических и транспортных свойств у материалов потенциальных матриц. Показано, что у образцов материалов из кости человека данные характеристики, как правило, значительно варьируют. Исходя из этого, становится очевидным, что отработка протоколов методов измерения вышеперечисленных свойств является важной работой для создания технологии биоинженерии тканевых имплантатов для восстановительной хирургии.

RF Magnetron Sputtering of Substituted Hydroxyapatite for Deposition of Biocoatings

Functionalization of titanium (Ti)-based alloy implant surfaces by deposition of calcium phosphates (CaP) has been widely recognized. Substituted hydroxyapatites (HA) allow the coating properties to be tailored based on the use of different Ca substitutes. The formation of antibacterial CaP coatings with the incorporation of Zn or Cu by an RF magnetron sputtering is proposed. The influence of RF magnetron targets elemental composition and structure in the case of Zn-HA and Cu-HA, and the influence of substrate’s grain size, the substrate’s temperature during the deposition, and post-deposition heat treatment (HT) on the resulting coatings are represented. Sintering the targets at 1150 °C resulted in a noticeable structural change with an increase in cell volume and lattice parameters for substituted HA. The deposition rate of Cu-HA and Zn-HA was notably higher compared to stochiometric HA (10.5 and 10) nm/min vs. 9 ± 0.5 nm/min, respectively. At the substrate temperature below 100 °C, all deposited coatings were found to be amorphous with an atomic short-range order corresponding to the {300} plane of crystalline HA. All deposited coatings were found to be hyper-stochiometric with Ca/P ratios varying from 1.9 to 2.5. An increase in the substrate temperature to 200 °C resulted in the formation of equiaxed grain structure on both coarse-grained (CG) and nanostructured (NS) Ti. The use of NS Ti notably increased the scratch resistance of the deposited coatings from18 ± 1 N to 22 ± 2 N. Influence of HT in air or Ar atmosphere is also discussed. Thus, the deposition of Zn- or Cu-containing CaP is a complex process that could be fine-tuned using the obtained research results

Effect of the Porosity, Roughness, Wettability, and Charge of Micro-Arc Coatings on the Efficiency of Doxorubicin Delivery and Suppression of Cancer Cells

Porous calcium phosphate coatings were formed by the micro-arc oxidation method on the surface of titanium for the loading and controlled release of the anticancer drug doxorubicin. The coatings’ morphology and microstructure were examined by scanning electron microscopy. The phase composition was determined with the help of X-ray diffraction analysis. Studies of the hydrophilic properties of the coatings and their zeta potential were carried out. Data on the kinetics of doxorubicin adsorption-desorption were obtained. In addition, the effect of calcium phosphate coatings impregnated with doxorubicin on the viability of the Neuro-2a cell line was revealed. The coating formed at low voltages of 200–250 V contained a greater number of branched communicating pores, and therefore they were able to adsorb a greater amount of doxorubicin. The surface charge also contributes to the process of the adsorption-desorption of doxorubicin, but this effect is not fully understood and further studies are required to identify it

Влияние продолжительности термической обработки на структуру и фазовый состав образцов сплава Co-Cr-Mo, полученных с помощью аддитивных технологий

Laser powder bed fusion (LPBF) requires application of powders with specific characteristics. These are near-spherical shape of particles, uniform elemental composition, typical particle size of 5 - 70 mu m, etc. Such powders are produced by spheroidization methods. They have such disadvantages as high cost and sale only in large quantities. There are publications describing application in LPBF powders, produced by the methods, alternative to spheroidiz,ation. In the current study, powders of pure raw Co, Cr and Mo were used for the production of Co-Cr-Mo powder mixture. Samples of Co-28 wt.% Cr-6 wt.% Mo alloy were produced by LPBF from this powder mixture. Due to the difference between melting temperatures of Co, Cr and Mo, inclusions of Cr and Mo were formed within the bulk of samples. Studies of phase and elemental composition, structure and microhardness of the as-produced samples and after post-treatment with varied duration are represented. As-produced samples have non-uniform elemental composition and are represented by the main Co-based phase. Increasing the annealing duration leads to the sequential dissolution of un-melted Cr and Mo inclusions. Complete dissolution of Cr particles was observed at 10 hours of treatment and complete dissolution of Mo particles was not observed after 20 hours of annealing. Microhardness non-linearly changes with the increasing duration of annealing. This is due to the phase transformations and diffusion processes occurring at such type of post-treatment. Complete dissolution of Mo-particles could be achieved by further increasing the annealing time or by varying the mode of laser powder bed fusion