28,732 research outputs found
Use of leaning vanes in a two stage fan
The use of leaning vanes for tone noise reduction was examined in terms of their application in a typical two-stage high pressure ratio fan. In particular for stages designed with outlet guide vanes and zero swirl between stages, leaning the vanes of the first stage stator was studied, since increasing the number of vanes and the gap between stages do not provide the desired advantage. It was shown that noise reduction at higher harmonics of blade passing frequency can be obtained by leaning the vanes
Control of interface reactions in SIC/TI composites
The reaction between a 0.5 to 1.0 Al film and a thick Ti substrate to form TiAl3 occurs very rapidly on heating to 635 C and causes the Al to be confined to the surface region. After heating to 900 C Ti3Al is formed with little release of Al into alpha Ti. Further annealing at 900 C eventually causes the Ti3Al phase to decompose and a substantial amount of Al is released into alpha Ti. The interdiffusion coefficient for Al in alpha Ti at 900 C increases by less than one order of magnitude as Al is varied from 0 to 20 at %. These data were obtained from the (101) X-ray diffraction intensity band using polycrystalline samples. Improvements in the analysis of X-ray diffraction data for the determination of composition profiles are discussed
Theoretical studies of tone noise from a fan rotor
An analytical study was made of some possible rotor alone noise sources of dipole, quadrapole and monopole characters which generate discrete tone noise. Particular emphasis is given to the tone noise caused by fan inlet flow distortion and turbulence. Analytical models are developed to allow prediction of absolute levels. Experimental data measured on a small scale fan is presented which indicates inlet turbulence interaction with a fan rotor can be a source of tone noise. Predicted and measured tone noise for the small scale rotor are shown to be in reasonable agreement
Design and breadboard evaluation of the SPS reference phase control system concept
The total breadboard system includes one pilot transmitter, one pilot receiver, nine phase distribution units, and two power transponders. With this complement of equipment, segments of a typical phase distribution system can be assembled to facilitate the evaluation of significant system parameters. The achievable accuracy of a large phase distribution system, the sensitivity of the system to parameter variations, and the limitations of commercially available components in such applications were determined
Theoretical studies on tone noise from a ducted fan rotor
The method of computing radiated noise from a ducted rotor due to inflow distortion and turbulence are examined. Analytical investigations include an appropriate description of sources, the cut-off conditions imposed on the modal propagation of the pressure waves in the annular duct, and reflections at the upstream end of the duct. Far field sound pressure levels at blade passing frequency due to acoustic radiation from a small scale low speed fan are computed. Theoretical predictions are in reasonable agreement with experimental measurements
Electrical and Magnetic behaviour of PrFeAsO0.8F0.2 superconductor
The superconducting and ground state samples of PrFeAsO0.8F0.2 and PrFeAsO
have been synthesised via easy and versatile single step solid state reaction
route. X-ray & Reitveld refine parameters of the synthesised samples are in
good agreement to the earlier reported value of the structure. The ground state
of the pristine compound (PrFeAsO) exhibited a metallic like step in
resistivity below 150K followed by another step at 12K. The former is
associated with the spin density wave (SDW) like ordering of Fe spins and later
to the anomalous magnetic ordering for Pr moments. Both the resistivity
anomalies are absent in case of superconducting PrFeAsO0.8F0.2 sample. Detailed
high field (up to 12Tesla) electrical and magnetization measurements are
carried out for superconducting PrFeAsO0.8F0.2 sample. The PrFeAsO0.8F0.2
exhibited superconducting onset (Tconset) at around 47K with Tc({\rho} =0) at
38K. Though the Tconset remains nearly invariant, the Tc({\rho} =0) is
decreased with applied field, and the same is around 23K under applied field of
12Tesla. The upper critical field (Hc2) is estimated from the Ginzburg Landau
equation (GL) fitting, which is found to be ~ 182Tesla. Critical current
density (Jc) being calculated from high field isothermal magnetization (MH)
loops with the help of Beans critical state model, is found to be of the order
of 103 A/cm2. Summarily, the superconductivity characterization of single step
synthesised PrFeAsO0.8F0.2 superconductor is presented.Comment: 15 Pages Text + Fig
An optimality criterion for sizing members of heated structures with temperature constraints
A thermal optimality criterion is presented for sizing members of heated structures with multiple temperature constraints. The optimality criterion is similar to an existing optimality criterion for design of mechanically loaded structures with displacement constraints. Effectiveness of the thermal optimality criterion is assessed by applying it to one- and two-dimensional thermal problems where temperatures can be controlled by varying the material distribution in the structure. Results obtained from the optimality criterion agree within 2 percent with results from a closed-form solution and with results from a mathematical programming technique. The thermal optimality criterion augments existing optimality criteria for strength and stiffness related constraints and offers the possibility of extension of optimality techniques to sizing structures with combined thermal and mechanical loading
- …