Fluid flow due to collective non-reciprocal motion of symmetrically-beating artificial cilia

Using a magneto-mechanical solid-fluid numerical model for permanently magnetic artificial cilia, we show that the metachronal motion of symmetrically beating cilia establishes a net pressure gradient in the direction of the metachronal wave, which creates a unidirectional flow. The flow generated is characterised as a function of the cilia spacing, the length of the metachronal wave, and a dimensionless parameter that characterises the relative importance of the viscous forces over the elastic forces in the cilia

Reynolds-number Dependence of Streamwise Velocity Fluctuations in Turbulent Pipe Flow

Statistics of the streamwise velocity component in fully-developed pipe flow are examined for Reynolds numbers in the range 5.5 x 10^4 < Re_D < 5.7 x 10^6. The second moment exhibits two maxima: one in the viscous sublayer is Reynolds-number dependent while the other, near the lower edge of the log region, is also Reynolds-number dependent and follows roughly the peak in Reynolds shear stress. The behaviour of both peaks is consistent with the concept of inactive motion which increases with increasing Reynolds number and decreasing distance from the wall. No simple scaling is apparent, and in particular, so-called "mixed" scaling is no better than wall scaling in the viscous sublayer and is actually worse than wall scaling in the outer region. The second moment is compared with empirical and theoretical scaling laws and some anomalies are apparent. The scaling of spectra using y, R and u_τ is examined. It appears that even at the highest Reynolds number, they exhibit incomplete similarity only: while spectra do collapse with either inner or outer scales for limited ranges of wave number, these ranges do not overlap. Thus similarity may not be described as complete and any apparent k_1^(-1) range does not attract any special significance and does not involve universal constants. It is suggested that this is because of the influence of inactive motion. Spectra also show the presence of very long structures close to the wall

Generic flow profiles induced by a beating cilium

We describe a multipole expansion for the low Reynolds number fluid flows generated by a localized source embedded in a plane with a no-slip boundary condition. It contains 3 independent terms that fall quadratically with the distance and 6 terms that fall with the third power. Within this framework we discuss the flows induced by a beating cilium described in different ways: a small particle circling on an elliptical trajectory, a thin rod and a general ciliary beating pattern. We identify the flow modes present based on the symmetry properties of the ciliary beat.Comment: 12 pages, 6 figures, to appear in EPJ

Scaling in Wall Turbulence: Scale Separation and Interaction (Invited Paper)

High Reynolds number pipe flow data are used to demonstrate the importance of several conditions related to scale separation that are either assumed in the classical theories or may be used in light of recent results in wall turbulence to infer a minimum Reynolds number condition above which scaling results may be suitable for extrapolation. Results from the Princeton Superpipe have suggested Re_τ > 5000 as the minimum Reynolds number for which key properties of pipe flow reach a “fully-developed” condition, based on observations of streamwise mean and turbulent velocity structure. Additional values related to finer constraints on the structural development are also discussed. A “skeleton” of wall turbulence is introduced, based on structural components identified as having a dominant role in the dynamics of near-wall turbulence in recent experiments by a variety of authors. Possible interaction mechanisms between these components are described alongside some outstanding questions concerning scale separation and interaction

Self-similarity of Mean Flow in Pipe Turbulence

Based on our previous modified log-wake law in turbulent pipe ‡flows, we invent two compound similarity numbers (Y;U), where Y is a combination of the inner variable y+ and outer variable , and U is the pure exect of the wall. The two similarity numbers can well collapse mean velocity profile data with different moderate and large Reynolds numbers into a single universal profile. We then propose an arctangent law for the buffer layer and a general log law for the outer region in terms of (Y;U). From Milikan’s maximum velocity law and the Princeton superpipe data, we derive the von Kármán constant = 0:43 and the additive constant B=6. Using an asymptotic matching method, we obtain a self-similarity law that describes the mean velocity profile from the wall to axis; and embeds the linear law in the viscous sublayer, the quartic law in the bursting sublayer, the classic log law in the overlap, the sine-square wake law in the wake layer, and the parabolic law near the pipe axis. The proposed arctangent law, the general log law and the self-similarity law have been compared with the high-quality data sets, with diffrent Reynolds numbers, including those from the Princeton superpipe, Loulou et al., Durst et al., Perry et al., and den Toonder and Nieuwstadt. Finally, as an application of the proposed laws, we improve the McKeon et al. method for Pitot probe displacement correction, which can be used to correct the widely used Zagarola and Smits data set

Analytical approach for entropy generation and heat transfer in CNT-nanofluid dynamics through a ciliated porous medium

The transportation of biological and industrial nanofluids by natural propulsion like cilia movement and self-generated contraction-relaxation of flexible walls has significant applications in numerous emerging technologies. Inspired by multi-disciplinary progress and innovation in this direction, a thermo-fluid mechanical model is proposed to study the entropy generation and convective heat transfer of nanofluids fabricated by the dispersion of single-wall carbon nanotubes (SWCNT) nanoparticles in water as the base fluid. The regime studied comprises heat transfer and steady, viscous, incompressible flow, induced by metachronal wave propulsion due to beating cilia, through a cylindrical tube containing a sparse (i.e. high permeability) homogenous porous medium. The flow is of the creeping type and is restricted under the low Reynolds number and long wavelength approximations. Slip effects at the wall are incorporated and the generalized Darcy drag-force model is utilized to mimic porous media effects. Cilia boundary conditions for velocity components are employed to determine analytical solutions to the resulting non-dimensionalized boundary value problem. The influence of pertinent physical parameters on temperature, axial velocity, pressure rise and pressure gradient, entropy generation function, Bejan number and stream-line distributions are computed numerically. A comparative study between SWCNT nanofluids and pure water is also computed. The computations demonstrate that axial flow is accelerated with increasing slip parameter and Darcy number and is greater for SWCNT- nanofluids than for pure water. Furthermore the size of the bolus for SWCNT-nanofluids is larger than that of the pure water. The study is applicable in designing and fabricating nanoscale and microfluidics devices, artificial cilia and biomimetic micro-pump

Out of cleanroom, self-assembled magnetic artificial cilia

Micrometer-sized hair-like structures called cilia,are abundant in nature and have various functionalities such as fluid pumping and sensing. Many efforts have been made to mimic the fluid pumping function of cilia, but most of the fabrication processes of these "artificial cilia" are tedious and expensive, hindering their practical applications. In this paper a cost-effective in situ fabrication technique is demonstrated. The cilia are constructed by self-assembly of micron sized magnetic beads and encapsulated with soft polymer coatings. Actuation of the cilia induces an effective fluid flow, and the cilia lengths and distribution can be adjusted by varying magnetic bead concentration and fabrication parameters