Preliminary experimental comparison and feasibility analysis of CO2/R134a mixture in Organic Rankine Cycle for waste heat recovery from diesel engines

This paper presents results of a preliminary experimental study of the Organic Rankine Cycle (ORC) using CO2/R134a mixture based on an expansion valve. The goal of the research was to examine the feasibility and effectiveness of using CO2 mixtures to improve system performance and expand the range of condensation temperature for ORC system. The mixture of CO2/R134a (0.6/0.4) on a mass basis was selected for comparison with pure CO2 in both the preheating ORC (P-ORC) and the preheating regenerative ORC (PR-ORC). Then, the feasibility and application potential of CO2/R134a (0.6/0.4) mixture for waste heat recovery from engines was tested under ambient cooling conditions. Preliminary experimental results using an expansion valve indicate that CO2/R134a (0.6/0.4) mixture exhibits better system performance than pure CO2. For PR-ORC using CO2/R134a (0.6/0.4) mixture, assuming a turbine isentropic efficiency of 0.7, the net power output estimation, thermal efficiency and exergy efficiency reached up to 5.30 kW, 10.14% and 24.34%, respectively. For the fitting value at an expansion inlet pressure of 10 MPa, the net power output estimation, thermal efficiency and exergy efficiency using CO2/R134a (0.6/0.4) mixture achieved increases of 23.3%, 16.4% and 23.7%, respectively, versus results using pure CO2 as the working fluid. Finally, experiments showed that the ORC system using CO2/R134a (0.6/0.4) mixture is capable of operating stably under ambient cooling conditions (25.2–31.5 °C), demonstrating that CO2/R134a mixture can expand the range of condensation temperature and alleviate the low-temperature condensation issue encountered with CO2. Under the ambient cooling source, it is expected that ORC using CO2/R134a (0.6/0.4) mixture will improve the thermal efficiency of a diesel engine by 1.9%

In Vitro Effects of Concomitant Use of Herbal Preparations on Cytochrome P450s Involved in Clozapine Metabolism

published_or_final_versio

Numerical Study on Indoor Wideband Channel Characteristics with Different Internal Wall

Effects of material and configuration of the internal wall on the performance of wideband channel are investigated by using the Finite Difference Time-Domain (FDTD) method. The indoor wideband channel characteristics, such as the path-loss, Root-Mean-Square (RMS) delay spread and number of the multipath components (MPCs), are presented. The simulated results demonstrate that the path-loss and MPCs are affected by the permittivity, dielectric loss tangent and thickness of the internal wall, while the RMS delay spread is almost not relevant with the dielectric permittivity. Furthermore, the comparison of simulated result with the measured one in a simple scenario has validated the simulation study

Experimental study on solidification/stabilization of Cr in stainless steel pickling sludge by high temperature roasting process

For stainless steel pickling sludge (SSPS) produced in a stainless steel factory in southeast China, Fly ash (FA) and waste glass (WG) were used as solidification/stabilization (S/S) agents to conduct high-temperature roasting experiments on S/S of Cr in SSPS, respectively. The effects of roasting temperature and S/S agent dosage on the S/S of Cr were studied. The results show that both FA and WG can take positive way to S/S. By adding 25 % of FA to SSPS at roasting temperature of 1 500 °C, the Cr leaching concentration of S/S products can decrease to 0,63 ppm. As for WG as S/S agent, the Cr leaching concentration of the product can be reduced to 0,45ppm when the dosage is 20 % and the roasting temperature is 1 400 °C,. Considering the dosage and roasting temperature, WG is suggested as a better S/S agent

Dynamical and sequential decay effects on isoscaling and density dependence of the symmetry energy

The isoscaling properties of the primary and final products are studied via isospin dependent quantum molecular dynamics (IQMD) model and the followed sequential decay model GEMINI, respectively. It is found that the isoscaling parameters $\alpha$ of both primary and final products keep no significant change for light fragments, but increases with the mass for intermediate and heavy products. The dynamical effects on isoscaling are exhibited by that $\alpha$ value decreases a little with the evolution time of the system, and opposite trend for the heavy products. The secondary decay effects on isoscaling are reflected in the increasing of the $\alpha$ value for the final products which experiences secondary decay process. Furthermore the density dependence of the symmetry energy has also been explored, it is observed that in the low densities the symmetry energy coefficient has the form of $C_{sym}(\rho)\sim C_{0}(\rho/\rho_{0})^{\gamma}$, where $\gamma = 0.7 \sim 1.3$ for both primary and final products, but $C_{0}$ have different values for primary and final products. It is also suggested that it might be more reasonable to describe the density dependence of the symmetry energy coefficient by the $C_{sym}(\rho/\rho_{0})\approx C_{1}(\rho/\rho_{0})^{\gamma_{soft}} + C_{2}(\rho/\rho_{0})^{\gamma_{stiff}}$ with $\gamma_{soft}\leq 1$, $\gamma_{stiff}\geq 1$ and $C_{1}, C_{2}$ constant parameters.Comment: 10 pages, 10 figure