Piezoelectric properties of zinc oxide nanostructure synthesized via chemical bath solution

We report our investigation on the growth of ZnO nanostructure on a patterned interdigitated microelectrode (IDE) using chemical bath deposition (CBD). Piezoresponse force microscopic techniques were used to characterise the piezoelectric material domain of the grown ZnO nanostructures. The synthesised ZnO nanostructures exhibits a hexagonal wurtzite structure with the c-axis preferred crystal orientation in the (002) plane. The average thickness of the ZnO seed layer was 467.5 nm, whereas the diameter and length of ZnO nanostructure were measured to be 2.73 μm and 6.96 μm respectively. The combine effect of Zinc nitrate and HTMA concentration and seed layer thickness are considered as the main reason for crystal morphology evolution. The ZnO nanostructures exhibited a phase switch of the response and hysteresis in the plot of phase versus dc voltage, as evidenced by the polarization exchanging of its ferroelectric behaviour. These results provide a fundamental understanding of piezoresponse ZnO nanostructure for future energy applications

Preparation and characterization of ZnO/ZnAl₂O₄-mixed metal oxides for dye-sensitized photodetector using Zn/Al-layered double hydroxide as precursor

In this article, a simple new technique has been developed for the preparation of ZnO/ZnAl₂O₄-mixed metal oxide (MMO) as anode materials for visible light dye-sensitized (DS) photodetector using Zn/Al-layered double hydroxide (LDH) as precursor. Subsequently, a detailed correlation between the structural properties of the prepared samples and the photo-responsive behavior of the fabricated DS photodetectors was elucidated. Specifically, it is evidenced that a high surface area of the prepared mesoporous MMO anode materials exhibit excellent dye absorptivity and thus facilitate free electron transfer and increase the photocurrent in the fabricated DS photodetector. A significant bathochromic shift was observed in the optical energy of the prepared MMO samples under the increment of molar ratio, providing a short electron transfer pathway in the optimized Z7A DS photodetector, which in turn demonstrated photo-responsivity and photo-detectivity of 6 mA/W and 1.7 × 10⁺¹⁰ Jones, respectively. This work presents an alternative approach for the design of an eco-friendly MMO-based DS photodetector

Surface engineering of ZnO nanorod for inverted organic solar cell

Crystallinity and band offset alignment of inorganic electron acceptor play a vital role in enhancing the device performance of inverted organic solar cell (IOSC). In this report, homogenous and vertically-aligned chemical treated ZnO nanorods (ZNR) were successfully grown on fluorine-doped tin oxide (FTO) substrate via a fully-solution method. It was found that the morphology of ZnO was fine-tuned from truncated surface to tubular structure under both of the anionic (KOH) and protonic (HCl) treatment. An extraordinary defect quenching phenomenon and hyperchromic energy band edge shift were observed in 0.1 M KOH-treated ZNR proven by the highest (0 0 2) peak detection and the lowest defect density. Compared with the pristine sample, the 0.1 M KOH-treated ZNR device showed a remarkable improvement in power conversion efficiency (PCE) up to 0.32%, signifying the effectiveness of anodic treatment. The robust correlation between the dependency of chemical treated ZNR and the device performance was established. This work elucidates a feasible method towards efficient IOSC devices development

Enhanced photovoltaic performance of CdS-sensitized inverted organic solar cells prepared via a successive ionic layer adsorption and reaction method

One-dimensional ZnO nanorods (ZNRs) synthesized on fluorine-doped tin oxide (FTO) glass by hydrothermal method were modified with cadmium sulfide quantum dots (CdS QDs) as an electron transport layer (ETL) in order to enhance the photovoltaic performance of inverted organic solar cell (IOSC). In present study, CdS QDs were deposited on ZNRs using a Successive Ionic Layer Adsorption and Reaction method (SILAR) method. In typical procedures, IOSCs were fabricated by spin-coating the P3HT:PC61BM photoactive layer onto the as-prepared ZNRs/CdS QDs. The results of current-voltage (I-V) measurement under illumination shows that the FTO/ZNRs/CdS QDs/ P3HT:PC61BM/ PEDOT: PSS/Ag IOSC achieved a higher power conversion efficiency (4.06 %) in comparison to FTO/ZNRs/P3HT:PC61BM/PEDOT: PSS/Ag (3.6 %). Our findings suggest that the improved open circuit voltage (Voc) and short circuit current density (Jsc) of ZNRs/CdS QDs devices could be attributed to enhanced electron selectivity and reduced interfacial charge carrier recombination between ZNRs and P3HT:PC61BM after the deposition of CdS QDs. The CdS QDs sensitized ZNRs reported herein exhibit great potential for advanced optoelectronic application

Synergy study on charge transport dynamics in hybrid organic solar cell: photocurrent mapping and performance analysis under local spectrum

Charge transport dynamics in ZnO based inverted organic solar cell (IOSC) has been characterized with transient photocurrent spectroscopy and localised photocurrent mapping-atomic force microscopy. The value of maximum exciton generation rate was found to vary from 2.6 × 1027 m−3s−1 (Jsat = 79.7 A m−2) to 2.9 × 1027 m−3s−1 (Jsat = 90.8 A m−2) for devices with power conversion efficiency ranging from 2.03 to 2.51%. These results suggest that nanorods served as an excellent electron transporting layer that provides efficient charge transport and enhances IOSC device performance. The photovoltaic performance of OSCs with various growth times of ZnO nanorods have been analysed for a comparison between AM1.5G spectrum and local solar spectrum. The simulated PCE of all devices operating under local spectrum exhibited extensive improvement with the gain of 13.3–13.7% in which the ZnO nanorods grown at 15 min possess the highest PCE under local solar with the value of 2.82%

Numerical analysis with experimental verification to predict outdoor power conversion efficiency of inverted organic solar devices

Inverted organic solar cell (IOSC) devices with different volume ratios of In₂S₃ nanoparticles have been studied under local spectral irradiances in Malaysia with respect to that of AM1.5G. The J-V curves of encapsulated IOSC devices were measured outdoor using an Ivium Potentiostat and local spectral irradiances were acquired using an AVANTES spectrometer concurrently. All of the IOSC devices experienced significant improvement in power conversion efficiency (PCE) under the both local sunny and cloudy conditions with respect to the AM 1.5G, by 22–35% and 31–65%, respectively. From spectral analysis, the area under the graph of spectral irradiance in UV–visible region is significantly higher compared to infrared region for both local sunny and cloudy conditions, by 44.6% and 55.9%, respectively, while it is only recorded as 12.9% for AM 1.5G. Last but not the least, we have successfully verified the numerical analysis to predict device performance by comparing the simulated and measured PCE values for different irradiance intensities whereby the prediction of PCE is better under sunny condition with a deviation of 3.4–10.8% compared to cloudy conditions, with deviation of 28.9–30.5%

Antimicrobial Drug Resistance in Singapore Hospitals

A new national antimicrobial resistance surveillance program in Singapore public hospitals that uses WHONET detected high levels of methicillin resistance among Staphylococcus aureus (35.3%), carbapenem resistance among Acinetobacter spp. (49.6%), and third-generation cephalosporin resistance among Klebsiella pneumoniae (35.9%) hospital isolates in 2006. Antimicrobial drug resistance is a major problem in Singapore

Metal free and sunlight driven g-C3N4 based photocatalyst using carbon quantum dots from Arabian dates: Green strategy for photodegradation of 2,4-dichlorophenol and selective detection of Fe3+

The fabrication of photocatalyst with a visible response and prolonged lifetime of charge carriers is a significant tactic to treat EDCs. In this work, a green synthesis route was adopted to prepare carbon quantum dots (CQDs) from Arabian dates (AD-CQDs) via hydrothermal method. The different weight percentages of fabricated AD-CQDs (10, 15 and 20 wt%) were coupled with graphitic carbon nitride (g-C3N4) to construct AD-CQDs/g-C3N4 composites to degrade 2,4-dicholorophenol (2,4-DCP) under sunlight irradiation with an average light intensity of ~973 × 100 lx. The obtained AD-CQDs were used as a highly selective sensor for ferric (Fe3+) ions, with a low detection limit of 1 nM. The increase loading of AD-CQDs resulted in particle agglomeration which decreased the specific surface area of g-C3N4 from 74.799 m2/g to 62.542 m2/g. The low specific surface area in the composites did not hamper the photocatalytic performance in which all composites showed a higher degradation rate than that of g-C3N4. With the optimum loading of AD-CQDs (20 wt%), the composite degraded 100% of 2,4-DCP in 90 min which was 1.7 times higher than g-C3N4 (59.48%). The excellent photocatalytic performance was mainly correlated to the effective separation of photogenerated electrons as evidenced by TRPL and transient photocurrent response. The second factor is visible light response because of the minor decrease of band gap energy as evidenced in UV–vis DRS spectra. Both factors are attributed to the dual functions of AD-CQDs as electron acceptors and photosensitizers. The simple and low-cost synthesis strategy could be an alternative to obtain sunlight driven photocatalysts without coupling with metal dopants or other semiconductors

Silver nanowires as flexible transparent electrode: role of PVP chain length

In this project, crystalline silver nanowires (AgNWs) are successfully grown using a continuous segmented flow process. The robust relationship among the structural, electrical and optical properties of the AgNWs in the function of the polyvinylpyrrolidone (PVP) chain length is elaborated. A concise carrier transport and a density mechanism are also discussed using a localized conductive atomic force microscopy analysis. The obtained results proved that the AgNWs synthesized using PVP with a chain length of 1.3 M exhibit excellent electrical and optical properties in the form of flexible transparent film with a sheet resistance of 90% at various bending angles. These findings present an alternative approach for production of AgNWs and fabrication of a high flexible transparent electrode

Integrating Bayesian Reasoning and Deep Learning

Deep learning (DL) has performed remarkable achievements on perception tasks by improving the complex structure with multiple layers. However, its inner structure is well-known as a black box because the users do not know the reasons why a certain decision is made. To overcome this shortcoming, Bayesian reasoning (BR) is proposed to integrate with DL where BR is an expressive knowledge representation, and it has explanation capability to reflect a cause-and-effect relationship. It relies on the probabilities which representing by a powerful probabilistic graphical model, Bayesian Network (BN). The study involved extracting the rule sets from Deep Neural Network (DNN) and extracted rules is used to construct an efficient BN. This proposed framework will aid the users to understand why a solution or decision is recommended based on the explanation provided