92 research outputs found
Study of the Mechanisms of Flux Pinning in Type 2 Superconductors
Flux pinning mechanisms in type-2 semiconductors and specific heat measurements on annealed and deformed pure niobium sample
Cryogenic magnetometer development Final report, 1 Jul. 1964 - 7 Mar. 1967
Magnetometers for measuring stable magnetic fields produced by low field superconducting shield
Recommended from our members
Interfacial Effects in Multilayers
Interfacial structure and the atomic interactions between atoms at interfaces in multilayers or nano-laminates have significant impact on the physical properties of these materials. A technique for the experimental evaluation of interfacial structure and interfacial structure effects is presented and compared to experiment. In this paper the impact of interfacial structure on the performance of x-ray, soft x-ray and extreme ultra-violet multilayer optic structures is emphasized. The paper is concluded with summary of these results and an assessment of their implications relative to multilayer development and the study of buried interfaces in solids in general
Recommended from our members
Mechanical Properties of Cu/Ta Multilayers Prepared by Magnetron Sputtering
The microstructure and mechanical properties of sputtered Cu/Ta multilayers were studied. X- ray diffraction and transmission electron microscopy characterization indicate that both the Ta and Cu in the 2 nm period multilayer are predominantly amorphous, while in longer period samples, the layers are crystalline, with the metastable tetragonal {beta}-Ta observed. No observable microstructure changes upon annealing at 300{degrees}C were found. An average Vickers micro- hardness value of about 5.5 GPa was measured, which increases about 5% upon annealing at 300{degrees}C. Residual stress in the multilayers and its dependence on thermal annealing are reported. The relationships between microstructure and mechanical properties in the multilayers are discussed
Recommended from our members
Nanostructure Multilayer Materials for Capacitor Energy Storage for Eh Vehicles
Acceleration and regenerative breaking for electric and hybrid vehicles require high power capacitors to complement energy sources. Large, flat nanostructure multilayer capacitors (NMCS) can provide load balancing capacitance in EHVs of the future. Additional uses include snubber capacitors for power electronics such as motor drives, energy discharge capacitors for lasers, and numerous industrial and military electronics applications [1]. In the present work, we demonstrate the effectiveness of LLNL`s multilayer materials technology by fabricating NMC test films with high energy and power density
Recommended from our members
High Energy Density Capacitors for Power Electronic Applications Using Nano-Structure Multilayer Technology
Power electronics applications are currently limited by capacitor size and performance. Only incremental improvements are anticipated in existing capacitor technologies, while significant performance advances are required in energy density and overall performance to meet the technical needs of the applications which are important for U.S. economic competitiveness. One application, the Power Electronic Building Block (PEBB), promises a second electronics revolution in power electronic design. High energy density capacitors with excellent electrical thermal and mechanical performance represent an enabling technology in the PEBB concept. We propose a continuing program to research and develop LLNL`s nano-structure multilayer technologies for making high voltage, high energy density capacitors. Our controlled deposition techniques are capable of synthesizing extraordinarily smooth sub-micron thick layers of dielectric and conductor materials. We have demonstrated that, with this technology, high voltage capacitors with an order of magnitude improvement in energy density are achievable
Recommended from our members
Techniques for in Situ HVEM Mechanical Deformation of Nanostructural Materials
We have developed two in-situ HVEM techniques which allow us to begin fundamental investigations into the mechanisms of deformation and fracture in nonstructured materials. A procedure for the observation of tensile deformation and failure in multilayers materials in cross-section is given and also the development of an in-situ HVEM nanoindentor of surfaces and films on surfaces in cross-section
Recommended from our members
Application of Soft X-Ray Lasers for Probing High Density Plasmas
The reliability and characteristics of collisionally pumped soft x-ray lasers make them ideal for a wide variety of plasma diagnostics. These systems now operate over a wavelength range extending from 35 to 400 {Angstrom} and have output energies as high as 10 mJ in 150 ps pulses. The beam divergence of these lasers is less than 15 mrad and they have a typical linewidth of {Delta}{lambda}/{lambda} {approximately} 10{sup -4} making them the brightest xuv sources available. In this paper we will describe the use of x-ray lasers to probe high density plasmas using a variety of diagnostic techniques. Using an x-ray laser and a multilayer mirror imaging system we have studied hydrodynamic imprinting of laser speckle pattern on directly driven thin foils with 1-2 {mu}m spatial resolution. Taking advantage of recently developed multilayer beamsplitters we have constructed and used a Mach-Zehnder interferometer operating at 155 {Angstrom} to probe 1-3 mm size laser produced plasmas with peak electron densities of 4 x 10{sup 21} cm{sup -3}. A comparison of our results with computer simulations will be presented
Recommended from our members
Electronic Effects at Interfaces in Cu-Cr, Mo, W, Ta, Re Multilayers
Interfacial electronic effects between Cu and the transition metals Cr, Mo, W, Ta, Re, are investigated by determining the strength of the white line absorption resonances on the L,,, edges of Cu in Cu{sub 5}/TM{sub 5} multilayers. X-ray absorption (XAS) was performed to study the white lines, which are directly related to the unoccupied states of Cu in the multilayers. The metallic multilayers are 2 mn in period and 200 mn in total thickness. Each period contains 5 monolayers of Cu and 5 monolayers of the transition metal: 40% of the atoms are at interfaces. These material pairs form ideal structures for the investigation of interfacial electronic effects as they form no compounds and exhibit terminal solid solubility. Only weak white lines are observed on the L3,2 edges of Cu since all the d-orbitals are filled. In the Cu/TM multilayers, however, we observed enhancement of the Cu white lines. We attribute this to the charge transfer from the `interfacial Cu atoms` d-orbital to the transition metal layers. Analysis of the white line enhancement enables calculation of the charge transfer from the Cu to the transition metal. Cu shows a charge transfer of about 0.03 electrons/interfacial Cu atom in Cu/Cr, 0.064 in Cu/Mo, 2048 0.35 in Cu/Ta, 0.17 in Cu/W , and 0.23 in Cu/Re. This charge transfer is consistent with the enhanced absorption energy of Cu on these materials as observed in thermal desorption experiments
Observation and Modeling of the Solar Transition Region: II. Solutions of the Quasi-Static Loop Model
In the present work we undertake a study of the quasi-static loop model and
the observational consequences of the various solutions found. We obtain the
most general solutions consistent with certain initial conditions. Great care
is exercised in choosing these conditions to be physically plausible (motivated
by observations). We show that the assumptions of previous quasi-static loop
models, such as the models of Rosner, Tucker and Vaiana (1978) and Veseckey,
Antiochos and Underwood (1979), are not necessarily valid for small loops at
transition region temperatures. We find three general classes of solutions for
the quasi-static loop model, which we denote, radiation dominated loops,
conduction dominated loops and classical loops. These solutions are then
compared with observations. Departures from the classical scaling law of RTV
are found for the solutions obtained. It is shown that loops of the type that
we model here can make a significant contribution to lower transition region
emission via thermal conduction from the upper transition region.Comment: 30 pages, 3 figures, Submitted to ApJ, Microsoft Word File 6.0/9
- …