131 research outputs found
Recommended from our members
Creating the Core Conditions of Extra-solar and Solar Giant Planets
Materials can be experimentally characterized at high pressures and densities by sending a laser-induced shock wave through a sample that is pre-compressed inside a diamond-anvil cell. This combination of static- and dynamic-compression methods has been experimentally demonstrated, and ultimately provides access to the 10-100 TPa (0.1-1 Gbar) pressure range that is relevant to planetary science. We report on dynamical measurements of the high pressure compressibility of helium, hydrogen and helium/hydrogen mixtures up to 230 GPa by combining laser shocks and static compression in diamond anvil cells. The initial density of samples in these precompressed targets has been varied by a factor of 3. The measurements on the principal He Hugoniot, i.e with the initial density of cryo-helium, is extended above 100 GPa and a maximum of compression ratio of greater than 5-fold of the initial density is observed. Also, a strong decrease in compressibility is observed by increasing the initial density. A similar data set has been produced for precompressed H{sub 2} and a mixture of He and H{sub 2}
Laser-Shock Compression and Hugoniot Measurements of Liquid Hydrogen to 55 GPa
The principal Hugoniot for liquid hydrogen was obtained up to 55 GPa under
laser-driven shock loading. Pressure and density of compressed hydrogen were
determined by impedance-matching to a quartz standard. The shock temperature
was independently measured from the brightness of the shock front. Hugoniot
data of hydrogen provide a good benchmark to modern theories of condensed
matter. The initial number density of liquid hydrogen is lower than that for
liquid deuterium, and this results in shock compressed hydrogen having a higher
compression and higher temperature than deuterium at the same shock pressure.Comment: 8 pages, 7 figures, 2 tables, accepted for publication in Physical
Review
Observation of collapsing radiative shocks in laboratory experiments
This article reports the observation of the dense, collapsed layer produced by a radiative shock in a laboratory experiment. The experiment uses laser irradiation to accelerate a thin layer of solid-density material to above 100 km/s100km∕s, the first to probe such high velocities in a radiative shock. The layer in turn drives a shock wave through a cylindrical volume of Xe gas (at ∼ 6 mg/cm3∼6mg∕cm3). Radiation from the shocked Xe removes enough energy that the shocked layer increases in density and collapses spatially. This type of system is relevant to a number of astrophysical contexts, providing the potential to observe phenomena of interest to astrophysics and to test astrophysical computer codes.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/87760/2/082901_1.pd
Recommended from our members
EXAFS Measurements of Laser-Shocked V and Ti and Crystal Phase Transformation in Ti
Extended X-Ray Absorption Fine Structure (EXAFS), using a laser-imploded target as a source, can yield the properties of laser-shocked metals on a nanosecond time scale. EXAFS measurements of vanadium shocked to {approx}0.4 Mbar yield the compression and temperature in good agreement with hydrodynamic simulations and shock-speed measurements. In laser-shocked titanium at the same pressure, the EXAFS modulation damping is much higher than warranted by the predicted temperature increase. This is shown to be due to the {alpha}-Ti to {omega}-Ti crystal-phase transformation, known to occur below {approx}0.1 Mbar for slower shock waves. The dynamics of material response to shock loading has been extensively studied in the past [1]. The goal of those studies has been to understand the shock-induced deformation and structural changes at the microscopic level [2]. Laser-generated shocks can be employed to broaden these studies to higher pressures ({approx}1 Mbar) and strain rates ({approx} 10{sup 7}-10{sup 8} s{sup -1}). Recently, laser-shocked materials have been studied with in-situ x-ray diffraction [3,4]. The goal of this work is to examine the use of in-situ EXAFS [5] as a complementary characterization of laser-shocked metals. EXAFS is the modulation in the x-ray absorption above the K edge (or L edge) due to the interference of the photoelectron waves with the waves reflected from neighboring atoms. The frequency of EXAFS modulations is related to the inter-particle distance, hence to the compression. The damping rate of the modulation can yield the lattice temperature, which is not readily available by other methods
- …